Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: Transition theory has been used to derive the elasticplastic
and transitional stresses. Results obtained have been discussed
numerically and depicted graphically. It is observed that the rotating
disk made of incompressible material with inclusion require higher
angular speed to yield at the internal surface as compared to disk
made of compressible material. It is seen that the radial and
circumferential stresses are maximum at the internal surface with and
without edge load (for flat disk). With the increase in thickness
parameter (k = 2, 4), the circumferential stress is maximum at the
external surface while the radial stress is maximum at the internal
surface. From the figures drawn the disk with exponentially varying
thickness (k = 2), high angular speed is required for initial yielding at
internal surface as compared to flat disk and exponentially varying
thickness for k = 4 onwards. It is concluded that the disk made of
isotropic compressible material is on the safer side of the design as
compared to disk made of isotropic incompressible material as it
requires higher percentage increase in an angular speed to become
fully plastic from its initial yielding.
Abstract: This paper presents an evaluation of the wind potential in the area of the Lagoon of Venice (Italy). A full anemometric campaign of 2 year measurements, performed by the "Osservatorio Bioclimatologico dell'Ospedale al Mare di Venezia" has been analyzed to obtain the Weibull wind speed distribution and the main wind directions. The annual energy outputs of two candidate horizontal-axis wind turbines (“Aventa AV-7 LoWind" and “Gaia Wind 133-11kW") have been estimated on the basis of the computed Weibull wind distribution, registering a better performance of the former turbine, due to a higher ratio between rotor swept area and rated power of the electric generator, determining a lower cut-in wind speed.
Abstract: The Learning Management Systems present learning
environment which offers a collection of e-learning tools in a
package that allows a common interface and information sharing
among the tools. South East European University initial experience
in LMS was with the usage of the commercial LMS-ANGEL. After a
three year experience on ANGEL usage because of expenses that
were very high it was decided to develop our own software. As part
of the research project team for the in-house design and development
of the new LMS, we primarily had to select the features that would
cover our needs and also comply with the actual trends in the area of
software development, and then design and develop the system. In
this paper we present the process of LMS in-house development for
South East European University, its architecture, conception and
strengths with a special accent on the process of migration and
integration with other enterprise applications.
Abstract: Electronic seal is an electronic device to check the
authenticity and integrity of freight containers at the point of arrival.
While RFID-based eSeals are gaining more acceptances and there are
also some standardization processes for these devices, a recent
research revealed that the current RFID-based eSeals are vulnerable to
various attacks. In this paper, we provide a feasible solution to
enhance the security of active RFID-based eSeals. Our approach is to
use an authentication and key agreement protocol between eSeal and
reader device, enabling data encryption and integrity check. Our
protocol is based on the use of block cipher AES, which is reasonable
since a block cipher can also be used for many other security purposes
including data encryption and pseudo-random number generation. Our
protocol is very simple, and it is applicable to low-end active RFID
eSeals.
Abstract: This paper presents a design method of self-tuning
Quantitative Feedback Theory (QFT) by using improved deadbeat
control algorithm. QFT is a technique to achieve robust control with
pre-defined specifications whereas deadbeat is an algorithm that
could bring the output to steady state with minimum step size.
Nevertheless, usually there are large peaks in the deadbeat response.
By integrating QFT specifications into deadbeat algorithm, the large
peaks could be tolerated. On the other hand, emerging QFT with
adaptive element will produce a robust controller with wider
coverage of uncertainty. By combining QFT-based deadbeat
algorithm and adaptive element, superior controller that is called selftuning
QFT-based deadbeat controller could be achieved. The output
response that is fast, robust and adaptive is expected. Using a grain
dryer plant model as a pilot case-study, the performance of the
proposed method has been evaluated and analyzed. Grain drying
process is very complex with highly nonlinear behaviour, long delay,
affected by environmental changes and affected by disturbances.
Performance comparisons have been performed between the
proposed self-tuning QFT-based deadbeat, standard QFT and
standard dead-beat controllers. The efficiency of the self-tuning QFTbased
dead-beat controller has been proven from the tests results in
terms of controller’s parameters are updated online, less percentage
of overshoot and settling time especially when there are variations in
the plant.
Abstract: The present study has been taken to explore the
screening of in vitro antimicrobial activities of D-galactose-binding
sponge lectin (HOL-30). HOL-30 was purified from the marine
demosponge Halichondria okadai by affinity chromatography. The
molecular mass of the lectin was determined to be 30 kDa with a
single polypeptide by SDS-PAGE under non-reducing and reducing
conditions. HOL-30 agglutinated trypsinized and glutaraldehydefixed
rabbit and human erythrocytes with preference for type O
erythrocytes. The lectin was subjected to evaluation for inhibition of
microbial growth by the disc diffusion method against eleven human
pathogenic gram-positive and gram-negative bacteria. The lectin
exhibited strong antibacterial activity against gram-positive bacteria,
such as Bacillus megaterium and Bacillus subtilis. However, it did
not affect against gram-negative bacteria such as Salmonella typhi
and Escherichia coli. The largest zone of inhibition was recorded of
Bacillus megaterium (12 in diameter) and Bacillus subtilis (10 mm in
diameter) at a concentration of the lectin (250 μg/disc). On the other
hand, the antifungal activity of the lectin was investigated against six
phytopathogenic fungi based on food poisoning technique. The lectin
has shown maximum inhibition (22.83%) of mycelial growth of
Botrydiplodia theobromae at a concentration of 100 μg/mL media.
These findings indicate that the lectin may be of importance to
clinical microbiology and have therapeutic applications.
Abstract: This paper presents a system for tracking the movement of laparoscopic instruments which is based on an orthogonal system of webcams and video image processing. The movements are captured with two webcams placed orthogonally inside of the physical trainer. On the image, the instruments were detected by using color markers placed on the distal tip of each instrument. The 3D position of the tip of the instrument within the work space was obtained by linear triangulation method. Preliminary results showed linearity and repeatability in the motion tracking with a resolution of 0.616 mm in each axis; the accuracy of the system showed a 3D instrument positioning error of 1.009 ± 0.101 mm. This tool is a portable and low-cost alternative to traditional tracking devices and a trustable method for the objective evaluation of the surgeon’s surgical skills.
Abstract: REY area has been located in Tehran Province and several archaeological ruins of this area indicate that the settlement in this area has been started since several thousand years ago. In this paper, the main investigation items consist of analysis of oil components and groundwater quality inside the wells. By finding the contents of oil in the well, it is possible to find out the pollution source by comparing the oil contents of well with other oil products that are used inside and outside of the oil farm. Investigation items consist of analysis of BTEX (Benzene, Toluene, Ethyl-benzene, Xylene), Gas chromatographic distillation characteristics, Water content, Density, Sulfur content, Lead content, Atmospheric distillation, MTBE(Methyl tertiary butyl ether). Analysis of polluting oil components showed that except MW(Monitoring Well)10 and MW 15 that oil with slightly heavy components was detected in them; with a high possibility the polluting oil is light oil.
Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: Composites based on a biodegradable polycaprolactone (PCL) containing 0.5, 1.0 and 2.0 wt % of titanium dioxide (TiO2) micro and nanoparticles were prepared by melt mixing and the effect of filler type and contents on the thermal properties, dynamic-mechanical behaviour and morphology were investigated. Measurements of storage modulus and loss modulus by dynamic mechanical analysis (DMA) showed better results for microfilled PCL/TiO2 composites than nanofilled composites, with the same filler content. DSC analysis showed that the Tg and Tc of micro and nanocomposites were slightly lower than those of neat PCL. The crystallinity of the PCL increased with the addition of TiO2 micro and nanoparticles; however, the cc for the PCL was unchanged with micro TiO2 content. The thermal stability of PCL/TiO2 composites were characterized using thermogravimetric analysis (TGA). The initial weight loss (5 wt %) occurs at slightly higher temperature with micro and nano TiO2 addition and with increasing TiO2 content.
Abstract: This paper describes a prototype aircraft that can fly
slowly, safely and transmit wireless video for tasks like reconnaissance,
surveillance and target acquisition. The aircraft is designed to
fly in closed quarters like forests, buildings, caves and tunnels which
are often spacious but GPS reception is poor. Envisioned is that a
small, safe and slow flying vehicle can assist in performing dull,
dangerous and dirty tasks like disaster mitigation, search-and-rescue
and structural damage assessment.
Abstract: Streaming Applications usually run in parallel or in
series that incrementally transform a stream of input data. It poses a
design challenge to break such an application into distinguishable
blocks and then to map them into independent hardware processing
elements. For this, there is required a generic controller that
automatically maps such a stream of data into independent processing
elements without any dependencies and manual considerations. In
this paper, Kahn Process Networks (KPN) for such streaming
applications is designed and developed that will be mapped on
MPSoC. This is designed in such a way that there is a generic Cbased
compiler that will take the mapping specifications as an input
from the user and then it will automate these design constraints and
automatically generate the synthesized RTL optimized code for
specified application.
Abstract: This article describes the aspects of the formation of
the national idea and national identity through the prism of gender
control and its contradistinction to the obsolete, Soviet component.
The role of females in ethnic and national projects is considered from
the point of view of Dr. Nira Yuval-Davis: as biological reproducers
of the ethnic communities- members; as reproducers of the boarders
of ethnic/national groups; as central participants in the ideological
reproduction of community and transducers of its culture; as symbols
in ideology, reproduction and transformation of ethnic/national
categories; and as participants of national, economical, political and
military combats. The society of the transitional type uses the
symbolic resources of the formation of gender component in the
national project. The gender patterns act like cultural codes,
executing the important ideological function in formation of the
national female- image, i.e. the discussion on hijab - it-s not just the
discussion on control over the female body, it-s the discussion on the
metaphor of social order.
Abstract: The purpose of this study was to investigate effects of
modality and redundancy principles on music theory learning among
pupils of different anxiety levels. The lesson of music theory was
developed in three different modes, audio and image (AI), text with
image (TI) and audio with image and text (AIT). The independent
variables were the three modes of courseware. The moderator
variable was the anxiety level, while the dependent variable was the
post test score. The study sample consisted of 405 third-grade pupils.
Descriptive and inferential statistics were conducted to analyze the
collected data. Analyses of covariance (ANCOVA) and Post hoc
were carried out to examine the main effects as well as the
interaction effects of the independent variables on the dependent
variable. The findings of this study showed that medium anxiety
pupils performed significantly better than low and high anxiety
pupils in all the three treatment modes. The AI mode was found to
help pupils with high anxiety significantly more than the TI and AIT
modes.
Abstract: Color printing proceeds with multiple halftone
separations overlay. Because of separation overlay misalignment in
printing, the percentage of different primary color combination may
vary and it will result in color shift. In traditional printing procedure
with AM halftone, every separation has different screening angle to
make the superposition pattern in a random style, which will reduce
the color shift. To evaluate the color shift of printing with hybrid
halftoning, we simulate printing procedure with halftone images
overlay and calculate the color difference between expected color and
color in different overlay misalignment configurations. The color
difference for hybrid halftone and AM halftone is very close. So the
color shift for hybrid halftone is acceptable with current color printing
procedure.
Abstract: A total of 33,680 nuclear power plants (NPPs) workers were monitored and recorded from 1990 to 2007. According to the record, the average individual radiation dose has been decreasing continually from it 3.20 mSv/man in 1990 to 1.12 mSv/man at the end of 2007. After the International Commission on Radiological Protection (ICRP) 60 recommendation was generalized in South Korea, no nuclear power plant workers received above 20 mSv radiation, and the numbers of relatively highly exposed workers have been decreasing continuously. The age distribution of radiation workers in nuclear power plants was composed of mainly 20-30- year-olds (83%) for 1990 ~ 1994 and 30-40-year-olds (75%) for 2003 ~ 2007. The difference in individual average dose by age was not significant. Most (77%) of NPP radiation exposures from 1990 to 2007 occurred mostly during the refueling period. With regard to exposure type, the majority of exposures were external exposures, representing 95% of the total exposures, while internal exposures represented only 5%. External effective dose was affected mainly by gamma radiation exposure, with an insignificant amount of neutron exposure. As for internal effective dose, tritium (3H) in the pressurized heavy water reactor (PHWR) was the biggest cause of exposure.
Abstract: Market based models are frequently used in the resource
allocation on the computational grid. However, as the size of
the grid grows, it becomes difficult for the customer to negotiate
directly with all the providers. Middle agents are introduced to
mediate between the providers and customers and facilitate the
resource allocation process. The most frequently deployed middle
agents are the matchmakers and the brokers. The matchmaking agent
finds possible candidate providers who can satisfy the requirements
of the consumers, after which the customer directly negotiates with
the candidates. The broker agents are mediating the negotiation with
the providers in real time.
In this paper we present a new type of middle agent, the marketmaker.
Its operation is based on two parallel operations - through
the investment process the marketmaker is acquiring resources and
resource reservations in large quantities, while through the resale process
it sells them to the customers. The operation of the marketmaker
is based on the fact that through its global view of the grid it can
perform a more efficient resource allocation than the one possible in
one-to-one negotiations between the customers and providers.
We present the operation and algorithms governing the operation
of the marketmaker agent, contrasting it with the matchmaker and
broker agents. Through a series of simulations in the task oriented
domain we compare the operation of the three agents types. We find
that the use of marketmaker agent leads to a better performance in the
allocation of large tasks and a significant reduction of the messaging
overhead.
Abstract: In-vitro mouse co-culture of E14 embryonic stem cells
(ESCs) and OP9 stromal cells can recapitulate the earliest stages of
haematopoietic development, not accessible in human embryos,
supporting both haemogenic precursors and their primitive
haematopoietic progeny. 1α, 25-Dihydroxy-vitamin D3 (VD3) has
been demonstrated to be a powerful differentiation inducer for a wide
variety of neoplastic cells, and could enhance early differentiation of
ESCs into blood cells in E14/OP9 co-culture. This study aims to
ascertain whether VD3 is key in promoting differentiation and
suppressing proliferation, by separately investigating the effects of
VD3 on the proliferation phase of the E14 cell line and on stromal
OP9 cells.The results showed that VD3 inhibited the proliferation of
the cells in a dose-dependent manner, quantitatively by decreased cell
number, and qualitatively by alkaline-phosphatase staining that
revealed significant differences between VD3-treated and untreated
cells, characterised by decreased enzyme expression (colourless
cells). Propidium-iodide cell-cycle analyses showed no significant
percentage change in VD3-treated E14 and OP9 cells within their G
and S-phases, compared to the untreated controls, despite the
increased percentage of G-phase compared to the S-phase in a dosedependent
manner. These results with E14 and OP9 cells indicate that
adequate VD3 concentration enhances cellular differentiation and
inhibits proliferation. The results also suggest that if E14 and OP9
cells were co-cultured andVD3-treated, there would be furtherenhanced
differentiation of ESCs into blood cells.
Abstract: Space exploration is a highly visible endeavour of
humankind to seek profound answers to questions about the origins
of our solar system, whether life exists beyond Earth, and how we
could live on other worlds. Different platforms have been utilized in
planetary exploration missions, such as orbiters, landers, rovers, and
penetrators.
Having low mass, good mechanical contact with the surface,
ability to acquire high quality scientific subsurface data, and ability to
be deployed in areas that may not be conducive to landers or rovers,
Penetrators provide an alternative and complimentary solution that
makes possible scientific exploration of hardly accessible sites (icy
areas, gully sites, highlands etc.).
The Canadian Space Agency (CSA) has put space exploration as
one of the pillars of its space program, and established ExCo program
to prepare Canada for future international planetary exploration.
ExCo sets surface mobility as its focus and priority, and invests
mainly in the development of rovers because of Canada's niche space
robotics technology. Meanwhile, CSA is also investigating how
micro-penetrators can help Canada to fulfill its scientific objectives
for planetary exploration.
This paper presents a review of the micro-penetrator technologies,
past missions, and lessons learned. It gives a detailed analysis of the
technical challenges of micro-penetrators, such as high impact
survivability, high precision guidance navigation and control, thermal
protection, communications, and etc. Then, a Canadian perspective of
a possible micro-penetrator mission is given, including Canadian
scientific objectives and priorities, potential instruments, and flight
opportunities.