Abstract: Ventilation is a fundamental requirement for
occupant health and indoor air quality in buildings. Natural
ventilation can be used as a design strategy in free-running
buildings to:
• Renew indoor air with fresh outside air and lower room
temperatures at times when the outdoor air is cooler.
• Promote air flow to cool down the building structure
(structural cooling).
• Promote occupant physiological cooling processes
(comfort cooling).
This paper focuses on ways in which ventilation can
provide the mechanism for heat dissipation and cooling of the
building structure..It also discusses use of ventilation as a
means of increasing air movement to improve comfort when
indoor air temperatures are too high. The main influencing
factors and design considerations and quantitative guidelines
to help meet the design objectives are also discussed.
Abstract: This paper proposes new hybrid approaches for face
recognition. Gabor wavelets representation of face images is an
effective approach for both facial action recognition and face
identification. Perform dimensionality reduction and linear
discriminate analysis on the down sampled Gabor wavelet faces can
increase the discriminate ability. Nearest feature space is extended to
various similarity measures. In our experiments, proposed Gabor
wavelet faces combined with extended neural net feature space
classifier shows very good performance, which can achieve 93 %
maximum correct recognition rate on ORL data set without any preprocessing
step.
Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: Truss spars are used for oil exploitation in deep and ultra-deep water if storage crude oil is not needed. The linear hydrodynamic analysis of truss spar in random sea wave load is necessary for determining the behaviour of truss spar. This understanding is not only important for design of the mooring lines, but also for optimising the truss spar design. In this paper linear hydrodynamic analysis of truss spar is carried out in frequency domain. The hydrodynamic forces are calculated using the modified Morison equation and diffraction theory. Added mass and drag coefficients of truss section computed by transmission matrix and normal acceleration and velocity component acting on each element and for hull section computed by strip theory. The stiffness properties of the truss spar can be separated into two components; hydrostatic stiffness and mooring line stiffness. Then, platform response amplitudes obtained by solved the equation of motion. This equation is non-linear due to viscous damping term therefore linearised by iteration method [1]. Finally computed RAOs and significant response amplitude and results are compared with experimental data.
Abstract: An important problem in speech research is the automatic extraction of information about the shape and dimensions of the vocal tract during real-time speech production. We have previously developed Southampton dynamic magnetic resonance imaging (SDMRI) as an approach to the solution of this problem.However, the SDMRI images are very noisy so that shape extraction is a major challenge. In this paper, we address the problem of tongue shape extraction, which poses difficulties because this is a highly deforming non-parametric shape. We show that combining active shape models with the dynamic Hough transform allows the tongue shape to be reliably tracked in the image sequence.
Abstract: This paper attempts to explain response components of Electrovestibulography (EVestG) using a computer simulation of a three-canal model of the vestibular system. EVestG is a potentially new diagnostic method for Meniere's disease. EVestG is a variant of Electrocochleography (ECOG), which has been used as a standard method for diagnosing Meniere's disease - it can be used to measure the SP/AP ratio, where an SP/AP ratio greater than 0.4-0.5 is indicative of Meniere-s Disease. In EVestG, an applied head tilt replaces the acoustic stimulus of ECOG. The EVestG output is also an SP/AP type plot, where SP is the summing potential, and AP is the action potential amplitude. AP is thought of as being proportional to the size of a population of afferents in an excitatory neural firing state. A simulation of the fluid volume displacement in the vestibular labyrinth in response to various types of head tilts (ipsilateral, backwards and horizontal rotation) was performed, and a simple neural model based on these simulations developed. The simple neural model shows that the change in firing rate of the utricle is much larger in magnitude than the change in firing rates of all three semi-circular canals following a head tilt (except in a horizontal rotation). The data suggests that the change in utricular firing rate is a minimum 2-3 orders of magnitude larger than changes in firing rates of the canals during ipsilateral/backward tilts. Based on these results, the neural response recorded by the electrode in our EVestG recordings is expected to be dominated by the utricle in ipsilateral/backward tilts (It is important to note that the effect of the saccule and efferent signals were not taken into account in this model). If the utricle response dominates the EVestG recordings as the modeling results suggest, then EVestG has the potential to diagnose utricular hair cell damage due to a viral infection (which has been cited as one possible cause of Meniere's Disease).
Abstract: The agricultural organic farming is different from
conventional farming in a way that is aimed at providing a balanced
and constructive action in agricultural systems. With the increase in
intensive agriculture, undesirable changes were being observed in
ecosystems with irreparable damage being caused to the natural
equilibrium. This is the reason for the increasing interest in organic
farming as an environment friendly agricultural production method.
In the present work three red fruits produced in organic farming were
analyzed, namely raspberry, gooseberry and blueberry. The samples
were harvested in a local farm when at plain maturation. The results
obtained allowed to conclude that the blueberry contained higher
amounts of phenolic compounds, total tannins and total anthocyanins
than raspberry and gooseberry. Furthermore, the HPLC analysis
allowed to identify monomeric anthocyanins and phenolic acids in
the three fruits studied.
Abstract: The modern world is experiencing fundamental and dynamic changes. The transformation of international relations; the end of confrontation and successive overcoming of the Cold War consequences have expanded possible international cooperation. The global nuclear conflict threat has been minimized, while a tendency to establish a unipolar world structure with the U.S. economic and power domination is growing. The current world system of international relations, apparently is secular. However, the religious beliefs of one or another nations play a certain (sometimes a key) role, both in the domestic affairs of the individual countries and in the development of bilateral ties. Political situation in Central Asia has been characterized by new factors such as international terrorism; religious extremism and radicalism; narcotrafficking and illicit arms trade of a global character immediately threaten to peace and political stability in Central Asia. The role and influence of Islamic fundamentalism is increasing; political ethnocentrism and the associated aggravation of inter-ethnic relations, the ambiguity of national interests and objectives of major geo-political groups in the Central Asian region regarding the division the political influence, emerge. This article approaches the following issues: the role of Islam in Central Asia; destabilizing factors in Central Asia; Islamic movements in Central Asia, Western Europe and the United States; the United States, Western Europe and Central Asia: religion, politics, ideology, and the US-Central Asia antiterrorism and religious extremism cooperation.
Abstract: The paper deals with the analysis of the dynamic
response of footbridges under human - induced dynamic loads.
This is a frequently occurring and often dominant load for
footbridges as it stems from the very purpose of a footbridge - to
convey pedestrian. Due to the emergence of new materials and
advanced engineering technology, slender footbridges are
increasingly becoming popular to satisfy the modern transportation
needs and the aesthetical requirements of the society. These
structures however are always lively with low stiffness, low mass,
low damping and low natural frequencies. As a consequence, they are
prone to vibration induced by human activities and can suffer severe
vibration serviceability problems, particularly in the lateral direction.
Pedestrian bridges are designed according to first and second limit
states, these are the criteria involved in response to static design load.
However, it is necessary to assess the dynamic response of bridge
design load on pedestrians and assess it impact on the comfort of the
user movement. Usually the load is considered a person or a small
group which can be assumed in perfect motion synchronization.
Already one person or small group can excite significant vibration of
the deck. In order to calculate the dynamic response to the movement
of people, designer needs available and suitable computational model
and criteria. For the calculation program ANSYS based on finite
element method was used.
Abstract: Low frequency power oscillations may be triggered
by many events in the system. Most oscillations are damped by the
system, but undamped oscillations can lead to system collapse.
Oscillations develop as a result of rotor acceleration/deceleration
following a change in active power transfer from a generator. Like
the operations limits, the monitoring of power system oscillating
modes is a relevant aspect of power system operation and control.
Unprevented low-frequency power swings can be cause of cascading
outages that can rapidly extend effect on wide region. On this regard,
a Wide Area Monitoring, Protection and Control Systems
(WAMPCS) help in detecting such phenomena and assess power
system dynamics security. The monitoring of power system
electromechanical oscillations is very important in the frame of
modern power system management and control. In first part, this
paper compares the different technique for identification of power
system oscillations. Second part analyzes possible identification
some power system dynamics behaviors Using Wide Area
Monitoring Systems (WAMS) based on Phasor Measurement Units
(PMUs) and wavelet technique.
Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: Some theoretical and experimental aspects related to
the conceptual analyses concerning the direct correspondence
identification between the shape, area and orientation of plantar
pressure and obtaining adequate corrective insoles by rapid
prototyping are presented in this paper. In the first part of the paper
there is the theoretical-correlative concept, which is the fundament of
correspondence deduction between plantar surface characteristics and
respectively corrective insoles. In the second part of the paper the
experimental equipment used to analyze and perform the
correspondence stages and then the integral ones between the
analyzed foot shapes and the ones with corrective insoles is
presented. In the final parte the results used to adapt the insoles
obtained by rapid prototyping but also some specific aspects and
conclusions of the conceptual analysis of direct and rapid
correspondence are shown.
Abstract: Fatigue life prediction and evaluation are the key
technologies to assure the safety and reliability of automotive rubber
components. The objective of this study is to develop the fatigue
analysis process for vulcanized rubber components, which is
applicable to predict fatigue life at initial product design step. Fatigue
life prediction methodology of vulcanized natural rubber was
proposed by incorporating the finite element analysis and fatigue
damage parameter of maximum strain appearing at the critical location
determined from fatigue test. In order to develop an appropriate
fatigue damage parameter of the rubber material, a series of
displacement controlled fatigue test was conducted using threedimensional
dumbbell specimen with different levels of mean
displacement. It was shown that the maximum strain was a proper
damage parameter, taking the mean displacement effects into account.
Nonlinear finite element analyses of three-dimensional dumbbell
specimens were performed based on a hyper-elastic material model
determined from the uni-axial tension, equi-biaxial tension and planar
test. Fatigue analysis procedure employed in this study could be used
approximately for the fatigue design.
Abstract: Distributed denial-of-service (DDoS) attacks pose a
serious threat to network security. There have been a lot of
methodologies and tools devised to detect DDoS attacks and reduce
the damage they cause. Still, most of the methods cannot
simultaneously achieve (1) efficient detection with a small number of
false alarms and (2) real-time transfer of packets. Here, we introduce
a method for proactive detection of DDoS attacks, by classifying the
network status, to be utilized in the detection stage of the proposed
anti-DDoS framework. Initially, we analyse the DDoS architecture
and obtain details of its phases. Then, we investigate the procedures
of DDoS attacks and select variables based on these features. Finally,
we apply the k-nearest neighbour (k-NN) method to classify the
network status into each phase of DDoS attack. The simulation result
showed that each phase of the attack scenario is classified well and
we could detect DDoS attack in the early stage.
Abstract: In this paper two mathematical models for definition of gas accidental escape localization in the gas pipelines are suggested. The first model was created for leak localization in the horizontal branched pipeline and second one for leak detection in inclined section of the main gas pipeline. The algorithm of leak localization in the branched pipeline did not demand on knowledge of corresponding initial hydraulic parameters at entrance and ending points of each sections of pipeline. For detection of the damaged section and then leak localization in this section special functions and equations have been constructed. Some results of calculations for compound pipelines having two, four and five sections are presented. Also a method and formula for the leak localization in the simple inclined section of the main gas pipeline are suggested. Some results of numerical calculations defining localization of gas escape for the inclined pipeline are presented.
Abstract: Typhoon Morakot hit Taiwan in 2009 and caused
severe damages. The government employs a compulsory relocation
strategy for post-disaster reconstruction. This study analyzes the
impact of this strategy on community solidarity. It employs a multiple
approach for data collection, including semi-structural interview,
secondary data, and documentation. The results indicate that the
government-s strategy for distributing housing has led to conflicts
within the communities. In addition, the relocating process has
stimulated tensions between victims of the disaster and those residents
whose lands were chosen to be new sites for relocation. The
government-s strategy of “collective relocation" also worsened
community integration. In addition, the fact that a permanent housing
community may accommodate people from different places also posts
challenge for the development of new inter-personal relations in the
communities. This study concludes by emphasizing the importance of
bringing social, economic and cultural aspects into consideration for
post-disaster relocation..
Abstract: We demonstrate a nonfaradaic electrochemical impedance spectroscopy measurement of biochemically modified gold plated electrodes using a two-electrode system. The absence of any redox indicator in the impedance measurements provide more precise and accurate characterization of the measured bioanalyte at molecular resolution. An equivalent electrical circuit of the electrodeelectrolyte interface was deduced from the observed impedance data of saline solution at low and high concentrations. The detection of biomolecular interactions was fundamentally correlated to electrical double-layer variation at modified interface. The investigations were done using 20mer deoxyribonucleic acid (DNA) strands without any label. Surface modification was performed by creating mixed monolayer of the thiol-modified single-stranded DNA and a spacer thiol (mercaptohexanol) by a two-step self-assembly method. The results clearly distinguish between the noncomplementary and complementary hybridization of DNA, at low frequency region below several hundreds Hertz.
Abstract: The seismic rehabilitation designs of two reinforced
concrete school buildings, representative of a wide stock of similar
edifices designed under earlier editions of the Italian Technical
Standards, are presented in this paper. The mutual retrofit solution
elaborated for the two buildings consists in the incorporation of a
dissipative bracing system including pressurized fluid viscous springdampers
as passive protective devices. The mechanical parameters,
layouts and locations selected for the constituting elements of the
system; the architectural renovation projects developed to properly
incorporate the structural interventions and improve the appearance
of the buildings; highlights of the installation works already
completed in one of the two structures; and a synthesis of the
performance assessment analyses carried out in original and
rehabilitated conditions, are illustrated. The results of the analyses
show a remarkable enhancement of the seismic response capacities of
both structures. This allows reaching the high performance objectives
postulated in the retrofit designs with much lower costs and
architectural intrusion as compared to traditional rehabilitation
interventions designed for the same objectives.
Abstract: –In this paper the damage in clamped-free, clampedclamped and free-free beam are analyzed considering samples
without and with structural modifications. The damage location is
investigated by the use of the bispectrum and wavelet analysis. The
mathematical models are obtained using 2D elasticity theory and the
Finite Element Method (FEM). The numerical and experimental data
are approximated using the Particle Swarm Optimizer (PSO) method
and this way is possible to adjust the localization and the severity of
the damage. The experimental data are obtained through
accelerometers placed along the sample. The system is excited using
impact hammer.
Abstract: Antiseismic property of telecommunication equipment
is very important for the grasp of the damage and the restoration after
earthquake. Telecommunication business operators are regulating
seismic standard for their equipments. These standards are organized
to simulate the real seismic situations and usually define the minimum
value of first natural frequency of the equipments or the allowable
maximum displacement of top of the equipments relative to bottom.
Using the finite element analysis, natural frequency can be obtained
with high accuracy but the relative displacement of top of the
equipments is difficult to predict accurately using the analysis.
Furthermore, in the case of simulating the equipments with access
floor, predicting the relative displacement of top of the equipments
become more difficult.
In this study, using enormous experimental datum, an empirical
formula is suggested to forecast the relative displacement of top of the
equipments. Also it can be known that which physical quantities are
related with the relative displacement.