Abstract: The main objective of this study was to determine if a
minimal increase in road light level (luminance) could lead to
improved driving performance among older adults. Older, middleaged
and younger adults were tested in a driving simulator following
vision and cognitive screening. Comparisons were made for the
performance of simulated night driving under two road light
conditions (0.6 and 2.5 cd/m2). At each light level, the effects of self
reported night driving avoidance were examined along with the
vision/cognitive performance. It was found that increasing road light
level from 0.6 cd/m2 to 2.5 cd/m2 resulted in improved recognition of
signage on straight highway segments. The improvement depends on
different driver-related factors such as vision and cognitive abilities,
and confidence. On curved road sections, the results showed that
driver-s performance worsened. It is concluded that while increasing
road lighting may be helpful to older adults especially for sign
recognition, it may also result in increased driving confidence and
thus reduced attention in some driving situations.
Abstract: This paper provides an exergy analysis of the multistage refrigeration cycle used for C2+ recovery plant. The behavior of an industrial refrigeration cycle with refrigerant propane has been investigated by the exergy method. A computational model based on the exergy analysis is presented for the investigation of the effects of the valves on the exergy losses, the second law of efficiency, and the coefficient of performance (COP) of a vapor compression refrigeration cycle. The equations of exergy destruction and exergetic efficiency for the main cycle components such as evaporators, condensers, compressors, and expansion valves are developed. The relations for the total exergy destruction in the cycle and the cycle exergetic efficiency are obtained. An ethane recovery unit with its refrigeration cycle has been simulated to prepare the exergy analysis. Using a typical actual work input value; the exergetic efficiency of the refrigeration cycle is determined to be 39.90% indicating a great potential for improvements. The simulation results reveal that the exergetic efficiencies of the heat exchanger and expansion sections get the lowest rank among the other compartments of refrigeration cycle. Refrigeration calculations have been carried out through the analysis of T–S and P–H diagrams where coefficient of performance (COP) was obtained as 1.85. The novelty of this article includes the effect and sensitivity analysis of molar flow, pressure drops and temperature on the exergy efficiency and coefficient of performance of the cycle.
Abstract: Ciprofloxacin (CIP) and Carbamazepine (CBZ), nonbiodegradable pharmaceutical residues, were become emerging pollutants in several aquatic environments. The objectives of this research were to study the possibility to recover these pharmaceuticals residues from pharmaceutical wastewater by increasing the selective adsorption on synthesized functionalized porous silicate, comparing with powdered activated carbon (PAC). Hexagonal mesoporous silicate (HMS), functionalized HMSs (3- aminopropyltriethoxy, 3- mercaptopropyltrimethoxy and noctyldimethyl) were synthesized and characterized physico-chemical characteristics. Obtained adsorption kinetics and isotherms showed that 3-mercaptopropyltrimethoxy functional groups grafted on HMS provided highest CIP and CBZ adsorption capacities; however, it was still lower than that of PAC. The kinetic results were compatible with pseudo-second order. The hydrophobicity and hydrogen bonding might play a key role on the adsorption. Furthermore, the capacities were affected by varying pH values due to the strength of hydrogen bonding between targeted compounds and adsorbents. Electrostatic interaction might not affect the adsorption capacities.
Abstract: We present a general comparison of punctual kriging based image restoration for different neighbourhood sizes. The formulation of the technique under consideration is based on punctual kriging and fuzzy concepts for image restoration in spatial domain. Three different neighbourhood windows are considered to estimate the semivariance at different lags for studying its effect in reduction of negative weights resulted in punctual kriging, consequently restoration of degraded images. Our results show that effect of neighbourhood size higher than 5x5 on reduction in negative weights is insignificant. In addition, image quality measures, such as structure similarity indices, peak signal to noise ratios and the new variogram based quality measures; show that 3x3 window size gives better performance as compared with larger window sizes.
Abstract: The whole work is based on possibility to use Lego Mindstorms robotics systems to reduce costs. Lego Mindstorms consists of a wide variety of hardware components necessary to simulate, programme and test of robotics systems in practice. To programme algorithm, which simulates space using the ultrasonic sensor, was used development environment supplied with kit. Software Matlab was used to render values afterwards they were measured by ultrasonic sensor. The algorithm created for this paper uses theoretical knowledge from area of signal processing. Data being processed by algorithm are collected by ultrasonic sensor that scans 2D space in front of it. Ultrasonic sensor is placed on moving arm of robot which provides horizontal moving of sensor. Vertical movement of sensor is provided by wheel drive. The robot follows map in order to get correct positioning of measured data. Based on discovered facts it is possible to consider Lego Mindstorm for low-cost and capable kit for real-time modelling.
Abstract: In this paper, we introduce a novel platform
encryption method, which modify its keys and random number
generators step by step during encryption algorithms. According to
complexity of the proposed algorithm, it was safer than any other
method.
Abstract: A complex valued neural network is a neural network, which consists of complex valued input and/or weights and/or thresholds and/or activation functions. Complex-valued neural networks have been widening the scope of applications not only in electronics and informatics, but also in social systems. One of the most important applications of the complex valued neural network is in image and vision processing. In Neural networks, radial basis functions are often used for interpolation in multidimensional space. A Radial Basis function is a function, which has built into it a distance criterion with respect to a centre. Radial basis functions have often been applied in the area of neural networks where they may be used as a replacement for the sigmoid hidden layer transfer characteristic in multi-layer perceptron. This paper aims to present exhaustive results of using RBF units in a complex-valued neural network model that uses the back-propagation algorithm (called 'Complex-BP') for learning. Our experiments results demonstrate the effectiveness of a Radial basis function in a complex valued neural network in image recognition over a real valued neural network. We have studied and stated various observations like effect of learning rates, ranges of the initial weights randomly selected, error functions used and number of iterations for the convergence of error on a neural network model with RBF units. Some inherent properties of this complex back propagation algorithm are also studied and discussed.
Abstract: This paper is taken into consideration the problem of cryptanalysis of stream ciphers. There is some attempts need to improve the existing attacks on stream cipher and to make an attempt to distinguish the portions of cipher text obtained by the encryption of plain text in which some parts of the text are random and the rest are non-random. This paper presents a tutorial introduction to symmetric cryptography. The basic information theoretic and computational properties of classic and modern cryptographic systems are presented, followed by an examination of the application of cryptography to the security of VoIP system in computer networks using LFSR algorithm. The implementation program will be developed Java 2. LFSR algorithm is appropriate for the encryption and decryption of online streaming data, e.g. VoIP (voice chatting over IP). This paper is implemented the encryption module of speech signals to cipher text and decryption module of cipher text to speech signals.
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: In this paper, an ultra low power and low jitter 12bit
CMOS digitally controlled oscillator (DCO) design is presented.
Based on a ring oscillator implemented with low power Schmitt
trigger based inverters. Simulation of the proposed DCO using 32nm
CMOS Predictive Transistor Model (PTM) achieves controllable
frequency range of 550MHz~830MHz with a wide linearity and high
resolution. Monte Carlo simulation demonstrates that the time-period
jitter due to random power supply fluctuation is under 31ps and the
power consumption is 0.5677mW at 750MHz with 1.2V power
supply and 0.53-ps resolution. The proposed DCO has a good
robustness to voltage and temperature variations and better linearity
comparing to the conventional design.
Abstract: Ionic liquids are well known as green solvents, reaction media and catalysis. Here, three different sulfonic acid functional ionic liquids prepared in the laboratory are used as catalysts in alkylation of p-cresol with tert-butyl alcohol. The kinetics on each of the catalysts was compared and a kinetic model was developed based on the product distribution over these catalysts. The kinetic parameters were estimated using Marquadt's algorithm to minimize the error function. The Arrhenius plots show a curvature which is best interpreted by the extended Arrhenius equation.
Abstract: We investigated the response of testosterone (T),
growth hormone (GH), cortisol (C), steroid hormone binding
globulin (SHBG), insulin-like growth factor (IGF-1), insulin-like
growth factor binding protein-3 (IGFBP-3), and some anaboliccatabolic
indexes, i.e.: T/C, T/SHBG, and IGF-1/IGFBP-3 to
maximal exercise in endurance-trained athletes (TREN) and
untrained subjects (CG). The baseline concentration of IGF-1 was
higher in athletes (TREN) when compared to the CG (p
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: Sensors have been used in various kinds of academic
fields and applications. In this article, we propose the idea of
modularized sensors that combine multiple sensor modules into a
unique sensor. We divide a sensor into several units according to
functionalities. Each unit has different sensor modules, which share
the same type of connectors and can be serially and arbitrarily
connected each other. A user can combine different sensor modules
into a sensor platform according to requirements. Compared with
current modularized sensors, the proposed sensor platform is highly
flexible and reusable. We have implemented the prototype of the
proposed sensor platform, and the experimental results show the
proposed platform can work correctly.
Abstract: In this paper, a new dependable algorithm based on an adaptation of the standard variational iteration method (VIM) is used for analyzing the transition from steady convection to chaos for lowto-intermediate Rayleigh numbers convection in porous media. The solution trajectories show the transition from steady convection to chaos that occurs at a slightly subcritical value of Rayleigh number, the critical value being associated with the loss of linear stability of the steady convection solution. The VIM is treated as an algorithm in a sequence of intervals for finding accurate approximate solutions to the considered model and other dynamical systems. We shall call this technique as the piecewise VIM. Numerical comparisons between the piecewise VIM and the classical fourth-order Runge–Kutta (RK4) numerical solutions reveal that the proposed technique is a promising tool for the nonlinear chaotic and nonchaotic systems.
Abstract: In determining the electromagnetic properties of
magnetic materials, hysteresis modeling is of high importance. Many
models are available to investigate those characteristics but they tend
to be complex and difficult to implement. In this paper a new
qualitative hysteresis model for ferromagnetic core is presented,
based on the function approximation capabilities of adaptive neuro
fuzzy inference system (ANFIS). The proposed ANFIS model
combined the neural network adaptive capabilities and the fuzzy
logic qualitative approach can restored the hysteresis curve with a
little RMS error. The model accuracy is good and can be easily
adapted to the requirements of the application by extending or
reducing the network training set and thus the required amount of
measurement data.
Abstract: From the beginning of creation, human being has ever
fought against the ecosystem by changes has made in environment.
The most environmental changes on the nature have been done after
starting the concentrated life in the same region. Dams are one of the
most important buildings in water resources and transferring. These
buildings have been made from old times without access to
hydrological, hydraulically, hydro mechanical information. Dams
have positive and negative effects on environment. Constructing a
dam relatively causes equal ecological consequences. According to
different criteria, environmental effects of dams can lead short term
and long term damages. These effects may influence on the situation
and treatment of meteorology, biology, culture, ancient works, etc
and severely causes to change and complicate it. So considering
importance of positive effects of dam construction, it is necessary to
minimize negative environmental effects of dams to achieve a stable
development. In this article the considered effects and their solutions
in influencing on assessment of destructive environmental effects of
dams construction have been surveyed and presented.
Abstract: The use of e-business in small and medium-sized
enterprises (SMEs) has been recently received an enormous attention
in information systems research by both academic and practitioners.
With the adoption of new and efficient technologies to enhance
businesses, Thai SMEs should be able to compete worldwide.
Unfortunately, most of the owners are not used to new technologies.
It is clear that most Thai SMEs prefer to work manually rather than
electronically. This paper aims to provide a fundamental conceptual
framework for E-business adoption by Thai SMEs. Rooted in
Knowledge transfer model, several factors are identified, which drive
and enable e-business adoption. By overlooking the benefits
associated with implementing new technologies, it is difficult for
Thai SMEs to perform well enough to compete globally. The paper
also helps Thai SMEs to understand factors related to E-business
adoption.