Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: Optimization of rational geometrical and mechanical
parameters of panel with curved plywood ribs is considered in this
paper. The panel consists of cylindrical plywood ribs manufactured
from Finish plywood, upper and bottom plywood flange, stiffness
diaphragms. Panel is filled with foam. Minimal ratio of structure self
weight and load that could be applied to structure is considered as
rationality criteria. Optimization is done, by using classical beam
theory without nonlinearities. Optimization of discreet design
variables is done by Genetic algorithm.
Abstract: The plastic forming process of sheet plate takes an
important place in forming metals. The traditional techniques of tool
design for sheet forming operations used in industry are experimental
and expensive methods. Prediction of the forming results,
determination of the punching force, blank holder forces and the
thickness distribution of the sheet metal will decrease the production
cost and time of the material to be formed. In this paper, multi-stage
deep drawing simulation of an Industrial Part has been presented
with finite element method. The entire production steps with
additional operations such as intermediate annealing and springback
has been simulated by ABAQUS software under axisymmetric
conditions. The simulation results such as sheet thickness
distribution, Punch force and residual stresses have been extracted in
any stages and sheet thickness distribution was compared with
experimental results. It was found through comparison of results, the
FE model have proven to be in close agreement with those of
experiment.
Abstract: Shear walls are used in most of the tall buildings for
carrying the lateral load. When openings for doors or windows are
necessary to be existed in the shear walls, a special type of the shear
walls is used called "coupled shear walls" which in some cases is
stiffened by specific beams and so, called "stiffened coupled shear
walls".
In this paper, a mathematical method for geometrically nonlinear
analysis of the stiffened coupled shear walls has been presented.
Then, a suitable formulation for determining the critical load of the
stiffened coupled shear walls under gravity force has been proposed.
The governing differential equations for equilibrium and deformation
of the stiffened coupled shear walls have been obtained by setting up
the equilibrium equations and the moment-curvature relationships for
each wall. Because of the complexity of the differential equation, the
energy method has been adopted for approximate solution of the
equations.
Abstract: Cryptography provides the secure manner of
information transmission over the insecure channel. It authenticates
messages based on the key but not on the user. It requires a lengthy
key to encrypt and decrypt the sending and receiving the messages,
respectively. But these keys can be guessed or cracked. Moreover,
Maintaining and sharing lengthy, random keys in enciphering and
deciphering process is the critical problem in the cryptography
system. A new approach is described for generating a crypto key,
which is acquired from a person-s iris pattern. In the biometric field,
template created by the biometric algorithm can only be
authenticated with the same person. Among the biometric templates,
iris features can efficiently be distinguished with individuals and
produces less false positives in the larger population. This type of iris
code distribution provides merely less intra-class variability that aids
the cryptosystem to confidently decrypt messages with an exact
matching of iris pattern. In this proposed approach, the iris features
are extracted using multi resolution wavelets. It produces 135-bit iris
codes from each subject and is used for encrypting/decrypting the
messages. The autocorrelators are used to recall original messages
from the partially corrupted data produced by the decryption process.
It intends to resolve the repudiation and key management problems.
Results were analyzed in both conventional iris cryptography system
(CIC) and non-repudiation iris cryptography system (NRIC). It
shows that this new approach provides considerably high
authentication in enciphering and deciphering processes.
Abstract: The purpose of this study was to elucidate the factors affecting antimicrobial effectiveness of essential oils against food spoilage and pathogenic bacteria. The minimum inhibition concentrations (MIC) of the essential oils, were determined by turbidimetric technique using Biocreen C, analyzer. The effects of pH ranging from 7.3 to 5.5 in absence and presence of essential oils and/or NaCl on the lag time and mean generation time of the bacteria at 370C, were carried out and results were determined showed that, combination of low pH and essential oil at 370C had additive effects against the test micro-organisms. The combination of 1.2 % (w/v) of NaCl and clove essential oil at 0.0325% (v/v) was effective against E. coli. The use of concentrations less than MIC in combination with low pH and or NaCl has the potential of being used as an alternative to “traditional food preservatives".
Abstract: This study describes a micro device integrated with
multi-chamber for polymerase chain reaction (PCR) with different
annealing temperatures. The device consists of the reaction
polydimethylsiloxane (PDMS) chip, a cover glass chip, and is
equipped with cartridge heaters, fans, and thermocouples for
temperature control. In this prototype, commercial software is utilized
to determine the geometric and operational parameters those are
responsible for creating the denaturation, annealing, and extension
temperatures within the chip. Two cartridge heaters are placed at two
sides of the chip and maintained at two different temperatures to
achieve a thermal gradient on the chip during the annealing step. The
temperatures on the chip surface are measured via an infrared imager.
Some thermocouples inserted into the reaction chambers are used to
obtain the transient temperature profiles of the reaction chambers
during several thermal cycles. The experimental temperatures
compared to the simulated results show a similar trend. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: In the last 15 years, a number of methods have been proposed for forecasting based on fuzzy time series. Most of the fuzzy time series methods are presented for forecasting of enrollments at the University of Alabama. However, the forecasting accuracy rates of the existing methods are not good enough. In this paper, we compared our proposed new method of fuzzy time series forecasting with existing methods. Our method is based on frequency density based partitioning of the historical enrollment data. The proposed method belongs to the kth order and time-variant methods. The proposed method can get the best forecasting accuracy rate for forecasting enrollments than the existing methods.
Abstract: To model the human visual system (HVS) in the region of interest, we propose a new objective metric evaluation adapted to wavelet foveation-based image compression quality measurement, which exploits a foveation setup filter implementation technique in the DWT domain, based especially on the point and region of fixation of the human eye. This model is then used to predict the visible divergences between an original and compressed image with respect to this region field and yields an adapted and local measure error by removing all peripheral errors. The technique, which we call foveation wavelet visible difference prediction (FWVDP), is demonstrated on a number of noisy images all of which have the same local peak signal to noise ratio (PSNR), but visibly different errors. We show that the FWVDP reliably predicts the fixation areas of interest where error is masked, due to high image contrast, and the areas where the error is visible, due to low image contrast. The paper also suggests ways in which the FWVDP can be used to determine a visually optimal quantization strategy for foveation-based wavelet coefficients and to produce a quantitative local measure of image quality.
Abstract: The asymmetric trafc between uplink and downlink
over recent mobile communication systems has been conspicuous because
of providing new communication services. This paper proposes
an asymmetric trafc accommodation scheme adopting a multihop
cooperative transmission technique for CDMA/FDD cellular networks.
The proposed scheme employs the cooperative transmission
technique in the already proposed downlink multihop transmissions
for the accommodation of the asymmetric trafc, which utilizes
the vacant uplink band for the downlink relay transmissions. The
proposed scheme reduces the transmission power at the downlink
relay transmissions and then suppresses the interference to the uplink
communications, and thus, improves the uplink performance. The
proposed scheme is evaluated by computer simulation and the results
show that it can achieve better throughput performance.
Abstract: An n×n matrix is called an N1 0 -matrix if all principal minors are non-positive and each entry is non-positive. In this paper, we study the partial non-combinatorially symmetric N1 0 -matrix completion problems if the graph of its specified entries is a transitive tournament or a double cycle. In general, these digraphs do not have N1 0 -completion. Therefore, we have given sufficient conditions that guarantee the existence of the N1 0 -completion for these digraphs.
Abstract: In this paper, a robust watermarking algorithm using
the wavelet transform and edge detection is presented. The efficiency
of an image watermarking technique depends on the preservation of
visually significant information. This is attained by embedding the
watermark transparently with the maximum possible strength. The
watermark embedding process is carried over the subband
coefficients that lie on edges, where distortions are less noticeable,
with a subband level dependent strength. Also, the watermark is
embedded to selected coefficients around edges, using a different
scale factor for watermark strength, that are captured by a
morphological dilation operation. The experimental evaluation of the
proposed method shows very good results in terms of robustness and
transparency to various attacks such as median filtering, Gaussian
noise, JPEG compression and geometrical transformations.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: An Ad hoc wireless network comprises of mobile
terminals linked and communicating with each other sans the aid of
traditional infrastructure. Optimized Link State Protocol (OLSR) is a
proactive routing protocol, in which routes are discovered/updated
continuously so that they are available when needed. Hello messages
generated by a node seeks information about its neighbor and if the
latter fails to respond to a specified number of hello messages
regulated by neighborhood hold time, the node is forced to assume
that the neighbor is not in range. This paper proposes to evaluate
OLSR routing protocol in a random mobility network having various
neighborhood hold time intervals. The throughput and delivery ratio
are also evaluated to learn about its efficiency for multimedia loads.
Abstract: An inflation–extension test with human vena cava
inferior was performed with the aim to fit a material model. The vein
was modeled as a thick–walled tube loaded by internal pressure and
axial force. The material was assumed to be an incompressible
hyperelastic fiber reinforced continuum. Fibers are supposed to be
arranged in two families of anti–symmetric helices. Considered
anisotropy corresponds to local orthotropy. Used strain energy
density function was based on a concept of limiting strain
extensibility. The pressurization was comprised by four pre–cycles
under physiological venous loading (0 – 4kPa) and four cycles under
nonphysiological loading (0 – 21kPa). Each overloading cycle was
performed with different value of axial weight. Overloading data
were used in regression analysis to fit material model. Considered
model did not fit experimental data so good. Especially predictions
of axial force failed. It was hypothesized that due to
nonphysiological values of loading pressure and different values of
axial weight the material was not preconditioned enough and some
damage occurred inside the wall. A limiting fiber extensibility
parameter Jm was assumed to be in relation to supposed damage.
Each of overloading cycles was fitted separately with different values
of Jm. Other parameters were held the same. This approach turned out
to be successful. Variable value of Jm can describe changes in the
axial force – axial stretch response and satisfy pressure – radius
dependence simultaneously.
Abstract: Modern highly automated production systems faces
problems of reliability. Machine function reliability results in
changes of productivity rate and efficiency use of expensive
industrial facilities. Predicting of reliability has become an important
research and involves complex mathematical methods and
calculation. The reliability of high productivity technological
automatic machines that consists of complex mechanical, electrical
and electronic components is important. The failure of these units
results in major economic losses of production systems. The
reliability of transport and feeding systems for automatic
technological machines is also important, because failure of transport
leads to stops of technological machines. This paper presents
reliability engineering on the feeding system and its components for
transporting a complex shape parts to automatic machines. It also
discusses about the calculation of the reliability parameters of the
feeding unit by applying the probability theory. Equations produced
for calculating the limits of the geometrical sizes of feeders and the
probability of sticking the transported parts into the chute represents
the reliability of feeders as a function of its geometrical parameters.
Abstract: The construction industry is the pillar industry in
China, accounting for about 6% of the gross domestic product. Along
with changes in the external environment of the construction industry
in China, the construction firm faces fierce competition. The paper
aims to investigate the relationship between diversified types of
construction firm and its performance in China. Based on generalist
and specialist strategy in organizational ecology, we think a generalist
organization can be applied to an enterprise with diversified
developments, while specialist groups are extended to professional
enterprises .This study takes advantage of annual financial data of
listed construction firm to empirically verify the relationship between
diversification and corporation performance establishing a regression
equation to econometric analysis. We find that: 1) Specialization can
significantly improve the level of profitability of listed construction
firms, and there is a significant positive relationship with corporate
performance; 2) The level of operating performance of listed
construction enterprises which engage in unrelated diversification is
higher than those with related diversification; 3) The relationship
between state-owned construction firms and corporate performance is
negative. The more the year of foundation is, the higher performance
will be; however, the more the year of being listed, the lower
performance will be.
Abstract: The effect of dry milling on the carbothermic
reduction of celestite was investigated. Mixtures of celestite
concentrate (98% SrSO4) and activated carbon (99% carbon) was
milled for 1 and 24 hours in a planetary ball mill. Un-milled and
milled mixtures and their products after carbothermic reduction were
studied by a combination of XRD and TGA/DTA experiments. The
thermogravimetric analyses and XRD results showed that by milling
celestite-carbon mixtures for one hour, the formation temperature of
strontium sulfide decreased from about 720°C (in un-milled sample)
to about 600°C, after 24 hours milling it decreased to 530°C. It was
concluded that milling induces increasingly thorough mixing of the
reactants to reduction occurring at lower temperatures
Abstract: Key management is a vital component in any modern security protocol. Due to scalability and practical implementation considerations automatic key management seems a natural choice in significantly large virtual private networks (VPNs). In this context IETF Internet Key Exchange (IKE) is the most promising protocol under permanent review. We have made a humble effort to pinpoint IKEv2 net gain over IKEv1 due to recent modifications in its original structure, along with a brief overview of salient improvements between the two versions. We have used US National Institute of Technology NIIST VPN simulator to get some comparisons of important performance metrics.