Abstract: In this study, a double-sided linear switched reluctance
motor (LSRM) drive was investigated as an alternative actuator for
vertical linear transportation applications such as a linear elevator
door, hospital and subway doors which move linearly and where
accurate position control and rapid response is requested. A prototype
sliding elevator door that is focused on a home elevator with LSRMs
is designed. The motor has 6/4 poles, 3 phases, 8A, 24V, 250 W and
250 N pull forces. Air gap between rotor and translator poles of the
designed motor and phase coil-s ideal inductance profile are obtained
in compliance with the geometric dimensions. Operation and
switching sections as motor and generator has been determined from
the inductance profile.
Abstract: The comparisons of two typical fluidic thrust vectoring exhaust nozzles including two-dimensional(2-D) nozzle and axisymmetric nozzle on aerodynamic characteristics was presented by numerical simulation. The results show: the thrust vector angles increased with the increasing secondary flow but decreased with the nozzle pressure ratio (NPR) increasing. With the same secondary flow and NPR, the thrust vector angles of 2-D nozzle were higher than the axisymmetric nozzle-s. So with the lower NPR and more secondary weight flow, the much higher thrust vector angle was caused by 2-D fluidic nozzle. And with the higher NPR and less secondary weight flow, there was not much difference in angular dimension between two nozzles.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: Real world Speaker Identification (SI) application
differs from ideal or laboratory conditions causing perturbations that
leads to a mismatch between the training and testing environment
and degrade the performance drastically. Many strategies have been
adopted to cope with acoustical degradation; wavelet based Bayesian
marginal model is one of them. But Bayesian marginal models
cannot model the inter-scale statistical dependencies of different
wavelet scales. Simple nonlinear estimators for wavelet based
denoising assume that the wavelet coefficients in different scales are
independent in nature. However wavelet coefficients have significant
inter-scale dependency. This paper enhances this inter-scale
dependency property by a Circularly Symmetric Probability Density
Function (CS-PDF) related to the family of Spherically Invariant
Random Processes (SIRPs) in Log Gabor Wavelet (LGW) domain
and corresponding joint shrinkage estimator is derived by Maximum
a Posteriori (MAP) estimator. A framework is proposed based on
these to denoise speech signal for automatic speaker identification
problems. The robustness of the proposed framework is tested for
Text Independent Speaker Identification application on 100 speakers
of POLYCOST and 100 speakers of YOHO speech database in three
different noise environments. Experimental results show that the
proposed estimator yields a higher improvement in identification
accuracy compared to other estimators on popular Gaussian Mixture
Model (GMM) based speaker model and Mel-Frequency Cepstral
Coefficient (MFCC) features.
Abstract: We study different types of aggregation operators and
the decision making process with minimization of regret. We analyze
the original work developed by Savage and the recent work
developed by Yager that generalizes the MMR method creating a
parameterized family of minimal regret methods by using the ordered
weighted averaging (OWA) operator. We suggest a new method that
uses different types of geometric operators such as the weighted
geometric mean or the ordered weighted geometric operator (OWG)
to generalize the MMR method obtaining a new parameterized family
of minimal regret methods. The main result obtained in this method
is that it allows to aggregate negative numbers in the OWG operator.
Finally, we give an illustrative example.
Abstract: In this paper the development of a software to
encrypt messages with asymmetric cryptography is presented. In
particular, is used the RSA (Rivest, Shamir and Adleman) algorithm
to encrypt alphanumeric information. The software allows to
generate different public keys from two prime numbers provided by
the user, the user must then select a public-key to generate the
corresponding private-key. To encrypt the information, the user must
provide the public-key of the recipient as well as the message to be
encrypted. The generated ciphertext can be sent through an insecure
channel, so that would be very difficult to be interpreted by an
intruder or attacker. At the end of the communication, the recipient
can decrypt the original message if provide his/her public-key and
his/her corresponding private-key.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: In this paper, a novel corner detection method is
presented to stably extract geometrically important corners.
Intensity-based corner detectors such as the Harris corner can detect
corners in noisy environments but has inaccurate corner position and
misses the corners of obtuse angles. Edge-based corner detectors such
as Curvature Scale Space can detect structural corners but show
unstable corner detection due to incomplete edge detection in noisy
environments. The proposed image-based direct curvature estimation
can overcome limitations in both inaccurate structural corner detection
of the Harris corner detector (intensity-based) and the unstable corner
detection of Curvature Scale Space caused by incomplete edge
detection. Various experimental results validate the robustness of the
proposed method.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: A multiphase harmonic load flow algorithm is developed based on backward/forward sweep to examine the effects of various factors on the neutral to earth voltage (NEV), including unsymmetrical system configuration, load unbalance and harmonic injection. The proposed algorithm composes fundamental frequency and harmonic frequencies power flows. The algorithm and the associated models are tested on IEEE 13 bus system. The magnitude of NEV is investigated under various conditions of the number of grounding rods per feeder lengths, the grounding rods resistance and the grounding resistance of the in feeding source. Additionally, the harmonic injection of nonlinear loads has been considered and its influences on NEV under different conditions are shown.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: In this paper we propose a novel approach for ascertaining human identity based on fusion of profile face and gait biometric cues The identification approach based on feature learning in PCA-LDA subspace, and classification using multivariate Bayesian classifiers allows significant improvement in recognition accuracy for low resolution surveillance video scenarios. The experimental evaluation of the proposed identification scheme on a publicly available database [2] showed that the fusion of face and gait cues in joint PCA-LDA space turns out to be a powerful method for capturing the inherent multimodality in walking gait patterns, and at the same time discriminating the person identity..
Abstract: Digital watermarking is one of the techniques for
copyright protection. In this paper, a normalization-based robust
image watermarking scheme which encompasses singular value
decomposition (SVD) and discrete cosine transform (DCT)
techniques is proposed. For the proposed scheme, the host image is
first normalized to a standard form and divided into non-overlapping
image blocks. SVD is applied to each block. By concatenating the
first singular values (SV) of adjacent blocks of the normalized image,
a SV block is obtained. DCT is then carried out on the SV blocks to
produce SVD-DCT blocks. A watermark bit is embedded in the highfrequency
band of a SVD-DCT block by imposing a particular
relationship between two pseudo-randomly selected DCT
coefficients. An adaptive frequency mask is used to adjust local
watermark embedding strength. Watermark extraction involves
mainly the inverse process. The watermark extracting method is blind
and efficient. Experimental results show that the quality degradation
of watermarked image caused by the embedded watermark is visually
transparent. Results also show that the proposed scheme is robust
against various image processing operations and geometric attacks.
Abstract: Understanding how airborne pathogens are
transported through hospital wards is essential for determining the
infection risk to patients and healthcare workers. This study utilizes
Computational Fluid Dynamics (CFD) simulations to explore
possible pathogen transport within a six-bed partitioned Nightingalestyle
hospital ward.
Grid independence of a ward model was addressed using the Grid
Convergence Index (GCI) from solutions obtained using three fullystructured
grids. Pathogens were simulated using source terms in
conjunction with a scalar transport equation and a RANS turbulence
model. Errors were found to be less than 4% in the calculation of air
velocities but an average of 13% was seen in the scalar field.
A parametric study of variations in the pathogen release point
illustrated that its distribution is strongly influenced by the local
velocity field and the degree of air mixing present.
Abstract: Design patterns describe good solutions to common
and reoccurring problems in program design. Applying design
patterns in software design and implementation have significant
effects on software quality metrics such as flexibility, usability,
reusability, scalability and robustness. There is no standard rule for
using design patterns. There are some situations that a pattern is
applied for a specific problem and this pattern uses another pattern.
In this paper, we study the effect of using chain of patterns on
software quality metrics.
Abstract: Sediment loads transfer in hydraulic installations and their consequences for the O&M of modern canal systems is emerging as one of the most important considerations in hydraulic engineering projects apriticularly those which are inteded to feed the irrigation and draiange schemes of large command areas such as the Dez and Mogahn in Iran.. The aim of this paper is to investigate the applicability of the vortex tube as a viable means of extracting sediment loads entering the canal systems in general and the water inatke structures in particulars. The Western conveyance canal of the Dez Diversion weir which feeds the Karkheh Flood Plain in Sothwestern Dezful has been used as the case study using the data from the Dastmashan Hydrometric Station. The SHARC software has been used as an analytical framework to interprete the data. Results show that given the grain size D50 and the canal turbulence the adaption length from the beginning of the canal and after the diversion dam is estimated at 477 m, a point which is suitable for laying the vortex tube.
Abstract: In this paper a new approach to face recognition is presented that achieves double dimension reduction making the system computationally efficient with better recognition results. In pattern recognition techniques, discriminative information of image increases with increase in resolution to a certain extent, consequently face recognition results improve with increase in face image resolution and levels off when arriving at a certain resolution level. In the proposed model of face recognition, first image decimation algorithm is applied on face image for dimension reduction to a certain resolution level which provides best recognition results. Due to better computational speed and feature extraction potential of Discrete Cosine Transform (DCT) it is applied on face image. A subset of coefficients of DCT from low to mid frequencies that represent the face adequately and provides best recognition results is retained. A trade of between decimation factor, number of DCT coefficients retained and recognition rate with minimum computation is obtained. Preprocessing of the image is carried out to increase its robustness against variations in poses and illumination level. This new model has been tested on different databases which include ORL database, Yale database and a color database. The proposed technique has performed much better compared to other techniques. The significance of the model is two fold: (1) dimension reduction up to an effective and suitable face image resolution (2) appropriate DCT coefficients are retained to achieve best recognition results with varying image poses, intensity and illumination level.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: This work offers a study of new simple compact model
of dual-drain Magnetic Field Effect Transistor (MAGFET) including
geometrical effects and biasing dependency. An explanation of the
sensitivity is investigated, involving carrier deflection as the dominant
operating principle. Finally, model verification with simulation results
is introduced to ensure that acceptable error of 2% is achieved.