Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: Apart from geometry, functionality is one of the most
significant hallmarks of a product. The functionality of a product can
be considered as the fundamental justification for a product
existence. Therefore a functional analysis including a complete and
reliable descriptor has a high potential to improve product
development process in various fields especially in knowledge-based
design. One of the important applications of the functional analysis
and indexing is in retrieval and design reuse concept. More than 75%
of design activity for a new product development contains reusing
earlier and existing design know-how. Thus, analysis and
categorization of product functions concluded by functional
indexing, influences directly in design optimization. This paper
elucidates and evaluates major classes for functional analysis by
discussing their major methods. Moreover it is finalized by
presenting a noble hybrid approach for functional analysis.
Abstract: Web intelligence, if made personal, can fuel the process of building communications around the interests and preferences of each individual customer or prospect, by providing specific behavioral insights about each individual. To become fully efficient, Web intelligence must reach a stage of a high-level maturity, passing throughout a process that involves five steps: (1) Web site analysis; (2) Web site and advertising optimization; (3) Segment targeting; (4) Interactive marketing (online only); and (5) Interactive marketing (online and offline). Discussing these steps in detail, the paper uncovers the real gold mine that is personal-level Web intelligence.
Abstract: Sulfide ion (S2-) is one of the most important ions to be
monitored due to its high toxicity, especially for aquatic organisms. In
this work, [Ca(2,2'-bipyridine)3]2+-intercalated montmorillonite was
prepared and used as a sensor to construct a potentiometric electrode to
measure sulfide ion in solution. The formation of [Ca(2,2'-
bipyridine)3]2+ in montmorillonite was confirmed by Fourier Transform
Infrared spectra. The electrode worked well at pH 4-12 and 4-10 in
sulfide solution 10-2 M and 10-3 M, respectively, in terms of Nernstian
slope. The sensor gave good precision and low cost.
Abstract: The evolution of technology and construction techniques has enabled the upgrading of transport networks. In particular, the high-speed rail networks allow convoys to peak at above 300 km/h. These structures, however, often significantly impact the surrounding environment. Among the effects of greater importance are the ones provoked by the soundwave connected to train transit. The wave propagation affects the quality of life in areas surrounding the tracks, often for several hundred metres. There are substantial damages to properties (buildings and land), in terms of market depreciation. The present study, integrating expertise in acoustics, computering and evaluation fields, outlines a useful model to select project paths so as to minimize the noise impact and reduce the causes of possible litigation. It also facilitates the rational selection of initiatives to contain the environmental damage to the already existing railway tracks. The research is developed with reference to the Italian regulatory framework (usually more stringent than European and international standards) and refers to a case study concerning the high speed network in Italy.
Abstract: Hydrogen that used as fuel in fuel cell vehicles can be
produced from renewable sources such as wind, solar, and hydro
technologies. PV-electrolyzer is one of the promising methods to
produce hydrogen with zero pollution emission. Hydrogen
production from a PV-electrolyzer system depends on the efficiency
of the electrolyzer and photovoltaic array, and sun irradiance at that
site. In this study, the amount of hydrogen is obtained using
mathematical equations for difference driving distance and sun peak
hours. The results show that the minimum of 99 PV modules are used
to generate 1.75 kgH2 per day for two vehicles.
Abstract: In this paper spatial variability of some chemical and
physical soil properties were investigated in mountain rangelands of
Nesho, Mazandaran province, Iran. 110 soil samples from 0-30 cm
depth were taken with systematic method on grid 30×30 m2 in
regions with different vegetation cover and transported to laboratory.
Then soil chemical and physical parameters including Acidity (pH),
Electrical conductivity, Caco3, Bulk density, Particle density, total
phosphorus, total Nitrogen, available potassium, Organic matter,
Saturation moisture, Soil texture (percentage of sand, silt and clay),
Sodium, Calcium, magnesium were measured in laboratory. Data
normalization was performed then was done statistical analysis for
description of soil properties and geostatistical analysis for indication
spatial correlation between these properties and were perpetrated
maps of spatial distribution of soil properties using Kriging method.
Results indicated that in the study area Saturation moisture and
percentage of Sand had highest and lowest spatial correlation
respectively.
Abstract: 2D/3D registration is a special case of medical image
registration which is of particular interest to surgeons. Applications
of 2D/3D registration are [1] radiotherapy planning and treatment
verification, spinal surgery, hip replacement, neurointerventions and
aortic stenting. The purpose of this paper is to provide a literature
review of the main methods for image registration for the 2D/3D
case. At the end of the paper an algorithm is proposed for 2D/3D
registration based on the Chebyssev polynomials iteration loop.
Abstract: In this article, we introduce a new approach for
analyzing UML designs to detect the inconsistencies between
multiple state diagrams and sequence diagrams. The Super State
Analysis (SSA) identifies the inconsistencies in super states, single
step transitions, and sequences. Because SSA considers multiple
UML state diagrams, it discovers inconsistencies that cannot be
discovered when considering only a single UML state diagram. We
have introduced a transition set that captures relationship information
that is not specifiable in UML diagrams. The SSA model uses the
transition set to link transitions of multiple state diagrams together.
The analysis generates three different sets automatically. These sets
are compared to the provided sets to detect the inconsistencies. SSA
identifies five types of inconsistencies: impossible super states,
unreachable super states, illegal transitions, missing transitions, and
illegal sequences.
Abstract: Knowledge Discovery in Databases (KDD) is the process of extracting previously unknown, hidden and interesting patterns from a huge amount of data stored in databases. Data mining is a stage of the KDD process that aims at selecting and applying a particular data mining algorithm to extract an interesting and useful knowledge. It is highly expected that data mining methods will find interesting patterns according to some measures, from databases. It is of vital importance to define good measures of interestingness that would allow the system to discover only the useful patterns. Measures of interestingness are divided into objective and subjective measures. Objective measures are those that depend only on the structure of a pattern and which can be quantified by using statistical methods. While, subjective measures depend only on the subjectivity and understandability of the user who examine the patterns. These subjective measures are further divided into actionable, unexpected and novel. The key issues that faces data mining community is how to make actions on the basis of discovered knowledge. For a pattern to be actionable, the user subjectivity is captured by providing his/her background knowledge about domain. Here, we consider the actionability of the discovered knowledge as a measure of interestingness and raise important issues which need to be addressed to discover actionable knowledge.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: This paper presents the study of a variable speed wind
energy conversion system based on a Doubly Fed Induction Generator
(DFIG) based on a sliding mode control applied to achieve control of
active and reactive powers exchanged between the stator of the DFIG
and the grid to ensure a Maximum Power Point Tracking (MPPT) of
a wind energy conversion system. The proposed control algorithm is
applied to a DFIG whose stator is directly connected to the grid and
the rotor is connected to the PWM converter. To extract a maximum
of power, the rotor side converter is controlled by using a stator
flux-oriented strategy. The created decoupling control between active
and reactive stator power allows keeping the power factor close to
unity. Simulation results show that the wind turbine can operate at
its optimum energy for a wide range of wind speed.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: Social media has led to paradigm shifts in ways
people work and do business, interact and socialize, learn and obtain
knowledge. So much so that social media has established itself as an
important spatial extension of this nation-s historicity and challenges.
Regardless of the enabling reputation and recommendation features
through social networks embedded in the social media system, the
overflow of broadcasted and publicized media contents turns the
table around from engendering trust to doubting the trust system.
When the trust is at doubt, the effects include deactivation of
accounts and creation of multiple profiles, which lead to the overflow
of 'ghost' contents (i.e. “the abundance of abandoned ships"). In
most literature, the study of trust can be related to culture; hence the
difference between Western-s “openness" and Eastern-s “blue-chip"
concepts in networking and relationships. From a survey on issues
and challenges among Malaysian social media users, 'authenticity'
emerges as one of the main factors that causes and is caused by other
factors. The other issue that has surfaced is credibility either in terms
of message/content and source. Another is the quality of the
knowledge that is shared. This paper explores the terrains of this
critical space which in recent years has been dominated increasingly
by, arguably, social networks embedded in the social media system,
the overflow of broadcasted and publicized media content.
Abstract: Most high-performance ac drives utilize a current
controller. The controller switches a voltage source inverter (VSI)
such that the motor current follows a set of reference current
waveforms. Fixed-band hysteresis (FBH) current control has been
widely used for the PWM inverter. We want to apply the same
controller for the PWM AC chopper. The aims of the controller is to
optimize the harmonic content at both input and output sides, while
maintaining acceptable losses in the ac chopper and to control in
wide range the fundamental output voltage. Fixed band controller has
been simulated and analyzed for a single-phase AC chopper and are
easily extended to three-phase systems. Simulation confirmed the
advantages and the excellent performance of the modulation method
applied for the AC chopper.
Abstract: Seemingly simple probabilities in the m-player game bingo have never been calculated. These probabilities include expected game length and the expected number of winners on a given turn. The difficulty in probabilistic analysis lies in the subtle interdependence among the m-many bingo game cards in play. In this paper, the game i got it!, a bingo variant, is considered. This variation provides enough weakening of the inter-player dependence to allow probabilistic analysis not possible for traditional bingo. The probability of winning in exactly k turns is calculated for a one-player game. Given a game of m-many players, the expected game length and tie probability are calculated. With these calculations, the game-s interesting payout scheme is considered.
Abstract: Date palm (Phoenix dactylifera L.) seeds are waste streams which are considered a major problem to the food industry. They contain potentially useful protein (10-15% of the whole date-s weight). Global production, industrialisation and utilisation of dates are increasing steadily. The worldwide production of date palm fruit has increased from 1.8 million tons in 1961 to 6.9 million tons in 2005, thus from the global production of dates are almost 800.000 tonnes of date palm seeds are not currently used [1]. The current study was carried out to convert the date palm seeds into useful protein powder. Compositional analysis showed that the seeds were rich in protein and fat 5.64 and 8.14% respectively. We used several laboratory scale methods to extract proteins from seed to produce a high protein powder. These methods included simple acid or alkali extraction, with or without ultrafiltration and phenol trichloroacetic acid with acetone precipitation (Ph/TCA method). The highest protein content powder (68%) was obtained by Ph/TCA method with yield of material (44%) whereas; the use of just alkali extraction gave the lowest protein content of 8%, and a yield of 32%.
Abstract: In this article, we propose a new surgical device for
circumferentially excision of high anal fistulas in a minimally
invasive manner. The new apparatus works on the basis of axially
rotating and moving a tubular blade along a fistulous tract
straightened using a rigid straight guidewire. As the blade moves
along the tract, its sharp circular cutting edge circumferentially
separates approximately 2.25 mm thickness of tract encircling the
rigid guidewire. We used the new set to excise two anal fistulas in a
62-year-old male patient, an extrasphincteric type and a long tract
with no internal opening. With regard to the results of this test, the
new device can be considered as a sphincter preserving mechanism
for treatment of high anal fistulas. Consequently, a major reduction
in the risk of fecal incontinence, recurrence rate, convalescence
period and patient morbidity may be achieved using the new device
for treatment of fistula-in-ano.
Abstract: Text categorization is the problem of classifying text documents into a set of predefined classes. After a preprocessing step the documents are typically represented as large sparse vectors. When training classifiers on large collections of documents, both the time and memory restrictions can be quite prohibitive. This justifies the application of features selection methods to reduce the dimensionality of the document-representation vector. Four feature selection methods are evaluated: Random Selection, Information Gain (IG), Support Vector Machine (called SVM_FS) and Genetic Algorithm with SVM (GA_FS). We showed that the best results were obtained with SVM_FS and GA_FS methods for a relatively small dimension of the features vector comparative with the IG method that involves longer vectors, for quite similar classification accuracies. Also we present a novel method to better correlate SVM kernel-s parameters (Polynomial or Gaussian kernel).