Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: This paper presents a new method for estimating the nonstationary
noise power spectral density given a noisy signal. The
method is based on averaging the noisy speech power spectrum using
time and frequency dependent smoothing factors. These factors are
adjusted based on signal-presence probability in individual frequency
bins. Signal presence is determined by computing the ratio of the
noisy speech power spectrum to its local minimum, which is updated
continuously by averaging past values of the noisy speech power
spectra with a look-ahead factor. This method adapts very quickly to
highly non-stationary noise environments. The proposed method
achieves significant improvements over a system that uses voice
activity detector (VAD) in noise estimation.
Abstract: This paper presents performance analysis of the
Evolutionary Programming-Artificial Neural Network (EPANN)
based technique to optimize the architecture and training parameters
of a one-hidden layer feedforward ANN model for the prediction of
energy output from a grid connected photovoltaic system. The ANN
utilizes solar radiation and ambient temperature as its inputs while the
output is the total watt-hour energy produced from the grid-connected
PV system. EP is used to optimize the regression performance of the
ANN model by determining the optimum values for the number of
nodes in the hidden layer as well as the optimal momentum rate and
learning rate for the training. The EPANN model is tested using two
types of transfer function for the hidden layer, namely the tangent
sigmoid and logarithmic sigmoid. The best transfer function, neural
topology and learning parameters were selected based on the highest
regression performance obtained during the ANN training and testing
process. It is observed that the best transfer function configuration for
the prediction model is [logarithmic sigmoid, purely linear].
Abstract: Drought is one of the most damaging climate-related
hazards, it is generally considered as a prolonged absence of
precipitation. This normal and recurring climate phenomenon had
plagued civilization throughout history because of the negative
impacts on economical, environmental and social sectors. Drought
characteristics are thus recognized as important factors in water
resources planning and management. The purpose of this study is to
detect the changes in drought frequency, persistence and severity
in the Ruhr river basin. The frequency of drought events was
calculated using the Standardized Precipitation Index (SPI). Used
data are daily precipitation records from seven meteorological
stations covering the period 1961-2007. The main benefit of the
application of this index is its versatility, only rainfall data is required
to deliver five major dimensions of a drought : duration, intensity,
severity, magnitude, and frequency. Furthermore, drought can be
calculated in different time steps. In this study SPI was calculated for
1, 3, 6, 9, 12, and 24 months. Several drought events were detected
in the covered period, these events contain mild, moderate and severe
droughts. Also positive and negative trends in the SPI values were
observed.
Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.
Abstract: Voltage stability has become an important issue to many power systems around the world due to the weak systems and long line on power system networks. In this paper, MATLAB load flow program is applied to obtain the weak points in the system combined with finding the voltage stability limit. The maximum permissible loading of a system, within the voltage stability limit, is usually determined. The methods for varying tap ratio (using tap changing transformer) and applying different values of shunt capacitor injection to improve the voltage stability within the limit are also provided.
Abstract: Riprap is mostly used to prevent erosion by flows
down the steep slopes in river engineering. A total of 53 stability tests
performed on angular riprap with a median stone size ranging from
15 to 278 mm and slope ranging from 1 to 40% are used in this study.
The existing equations for the prediction of medium size of angular
stones are checked for their accuracy using the available data.
Predictions of median size using these equations are not satisfactory
and results show deviation by more than ±20% from the observed
values. A multivariable power regression analysis is performed to
propose a new equation relating the median size with unit discharge,
bed slope, riprap thickness and coefficient of uniformity. The
proposed relationship satisfactorily predicts the median angular stone
size with ±20% error. Further, the required size of the rounded stone
is more than the angular stone for the same unit discharge and the
ratio increases with unit discharge and also with embankment slope
of the riprap.
Abstract: This paper presents the generation of bipolar square
wave pulses with characteristics that are suitable for liquid food
sterilization using a Cascaded H-bridge Multilevel Inverter (CHMI).
Bipolar square waves pulses have been reported as stable for a
longer time during the sterilization process with minimum heat
emission and increased efficiency. The CHMI allows the system to
produce bipolar square wave pulses and yielding high output voltage
without using a transformer while fulfilling the pulse requirements
for effective liquid food sterilization. This in turn can reduce power
consumption and cost of the overall liquid food sterilization system.
The simulation results have shown that pulses with peak output
voltage of 2.4 kV, pulse width of between 1 2s and 1 ms at
frequencies of 50 Hz and 100 Hz can be generated by a 7-level
CHMI. Results from the experimental set-up based on a 5-level
CHMI has indicated the potential of the proposed circuit in
producing bipolar square wave output pulses with peak values that
depends on the DC source level supplied to the CHMI modules,
pulse width of between 12.5 2s and 1 ms at frequencies of 50 Hz
and 100 Hz.
Abstract: Tuberculosis (TB) is a bacterial infectious disease caused by the obligate human pathogen, Mycobacterium tuberculosis. Multidrug-resistant tuberculosis (MDR-TB) is a global reality that threatens tuberculosis control. Resistance to antibiotic Rifampicin, occurs in 95% of cases through nucleotide substitutions in an 81-bp core region of the rpoB i.e; beta subunit of DNA dependant RNA polymerase. In this paper, we studied the Rifampicin-rpoB receptor interactions In silico. First, homology modeling was performed to obtain the three dimensional structure of Mycobacterium rpoB. Sixty analogs of Rifampicin were prepared using Marvin sketch software. Both original Rifampicin and the analogs were docked with rpoB and energy values were obtained. Out of sixty analogs, 43 analogs had lesser energy values than conventional Rifampicin and hence are predicted to have greater binding affinity to rpoB. Thus, this study offers a route for the development of Rifampicin analogs against multi drug resistant Mycobacterium rpoB.
Abstract: In this paper, we propose an easily computable proximity index for predicting voltage collapse of a load bus using only measured values of the bus voltage and power; Using these measurements a polynomial of fourth order is obtained by using LES estimation algorithms. The sum of the absolute values of the polynomial coefficient gives an idea of the critical bus. We demonstrate the applicability of our proposed method on 6 bus test system. The results obtained verify its applicability, as well as its accuracy and the simplicity. From this indicator, it is allowed to predict the voltage instability or the proximity of a collapse. Results obtained by the PV curve are compared with corresponding values by QV curves and are observed to be in close agreement.
Abstract: Linear stability analysis of wake-shear layers in twophase
shallow flows is performed in the present paper. Twodimensional
shallow water equations are used in the analysis. It is
assumed that the fluid contains uniformly distributed solid particles.
No dynamic interaction between the carrier fluid and particles is
expected in the initial moment. The stability calculations are
performed for different values of the particle loading parameter and
two other parameters which characterize the velocity ratio and the
velocity deficit. The results show that the particle loading parameter
has a stabilizing effect on the flow while the increase in the velocity
ratio or in the velocity deficit destabilizes the flow.
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: Probability-based identity disclosure risk
measurement may give the same overall risk for different
anonymization strategy of the same dataset. Some entities in the
anonymous dataset may have higher identification risks than the
others. Individuals are more concerned about higher risks than the
average and are more interested to know if they have a possibility of
being under higher risk. A notation of overall risk in the above
measurement method doesn-t indicate whether some of the involved
entities have higher identity disclosure risk than the others. In this
paper, we have introduced an identity disclosure risk measurement
method that not only implies overall risk, but also indicates whether
some of the members have higher risk than the others. The proposed
method quantifies the overall risk based on the individual risk values,
the percentage of the records that have a risk value higher than the
average and how larger the higher risk values are compared to the
average. We have analyzed the disclosure risks for different
disclosure control techniques applied to original microdata and
present the results.
Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.
Abstract: We present a hybrid architecture of recurrent neural
networks (RNNs) inspired by hidden Markov models (HMMs). We
train the hybrid architecture using genetic algorithms to learn and
represent dynamical systems. We train the hybrid architecture on a
set of deterministic finite-state automata strings and observe the
generalization performance of the hybrid architecture when presented
with a new set of strings which were not present in the training data
set. In this way, we show that the hybrid system of HMM and RNN
can learn and represent deterministic finite-state automata. We ran
experiments with different sets of population sizes in the genetic
algorithm; we also ran experiments to find out which weight
initializations were best for training the hybrid architecture. The
results show that the hybrid architecture of recurrent neural networks
inspired by hidden Markov models can train and represent dynamical
systems. The best training and generalization performance is
achieved when the hybrid architecture is initialized with random real
weight values of range -15 to 15.
Abstract: Attempt was made to improve certain characteristics of bio-oil derived from palm kernel pyrolysis by blending it with diesel fuel and alcohols. Two types of alcohol, ethanol or butanol, was used as cosolvent to stabilize the phase of ternary systems. Phase behaviors and basic fuel properties of palm kernel bio-oildiesel- alcohol systems were investigated in this study. Alcohol types showed a significant influence on the phase characteristics with palm kernel bio-oil-diesel-butanol system giving larger soluble area than that of palm kernel bio-oil-diesel-ethanol system. For fuel properties, blended fuels showed superior properties including lower values of density (~860 kg/m3 at 25°C), viscosity (~4.12 mm2/s at 40°C), carbon residue (1.02-2.53 wt%), ash (0.018-0.034 wt%) and pour point (
Abstract: Cast metal inlays can be used on molars requiring a
class II restoration instead amalgam and offer a durable alternative.
Because it is known that class II inlays may increase the
susceptibility to fracture, it is important to ensure optimal
performance in selection of the adequate preparation design to reduce
stresses in teeth structures and also in the restorations. The aim of the
study was to investigate the influence of preparation design on stress
distribution in molars with different class II preparations and in cast
metal inlays. The first step of the study was to achieve 3D models in
order to analyze teeth and cast metal class II inlays. The geometry of
the intact tooth was obtained by 3D scanning using a manufactured
device. With a NURBS modeling program the preparations and the
appropriately inlays were designed. 3D models of first upper molars
of the same shape and size were created. Inlay cavities designs were
created using literature data. The geometrical model was exported
and the mesh structure of the solid 3D model was created for
structural simulations. Stresses were located around the occlusal
contact areas. For the studied cases, the stress values were not
significant influenced by the taper of the preparation. it was
demonstrated stresses are higher in the cast metal restorations and
therefore the strength of the teeth is not affected.
Abstract: Image registration plays an important role in the
diagnosis of dental pathologies such as dental caries, alveolar bone
loss and periapical lesions etc. This paper presents a new wavelet
based algorithm for registering noisy and poor contrast dental x-rays.
Proposed algorithm has two stages. First stage is a preprocessing
stage, removes the noise from the x-ray images. Gaussian filter has
been used. Second stage is a geometric transformation stage.
Proposed work uses two levels of affine transformation. Wavelet
coefficients are correlated instead of gray values. Algorithm has been
applied on number of pre and post RCT (Root canal treatment)
periapical radiographs. Root Mean Square Error (RMSE) and
Correlation coefficients (CC) are used for quantitative evaluation.
Proposed technique outperforms conventional Multiresolution
strategy based image registration technique and manual registration
technique.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: This paper proposes rough set models with three
different level knowledge granules in incomplete information system
under tolerance relation by similarity between objects according to
their attribute values. Through introducing dominance relation on the
discourse to decompose similarity classes into three subclasses: little
better subclass, little worse subclass and vague subclass, it dismantles
lower and upper approximations into three components. By using
these components, retrieving information to find naturally hierarchical
expansions to queries and constructing answers to elaborative queries
can be effective. It illustrates the approach in applying rough set
models in the design of information retrieval system to access different
granular expanded documents. The proposed method enhances rough
set model application in the flexibility of expansions and elaborative
queries in information retrieval.