Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: A Multi-dimensional computational fluid dynamics
(CFD) two-phase model was developed with the aim to simulate
the in-core coolant circuit of a pressurized heavy water reactor
(PHWR) of a commercial nuclear power plant (NPP). Due to the
fact that this PHWR is a Reactor Pressure Vessel type (RPV),
three-dimensional (3D) detailed modelling of the large reservoirs of
the RPV (the upper and lower plenums and the downcomer) were
coupled with an in-house finite volume one-dimensional (1D) code
in order to model the 451 coolant channels housing the nuclear fuel.
Regarding the 1D code, suitable empirical correlations for taking into
account the in-channel distributed (friction losses) and concentrated
(spacer grids, inlet and outlet throttles) pressure losses were used.
A local power distribution at each one of the coolant channels
was also taken into account. The heat transfer between the coolant
and the surrounding moderator was accurately calculated using a
two-dimensional theoretical model. The implementation of subcooled
boiling and condensation models in the 1D code along with the use
of functions for representing the thermal and dynamic properties of
the coolant and moderator (heavy water) allow to have estimations
of the in-core steam generation under nominal flow conditions for a
generic fission power distribution. The in-core mass flow distribution
results for steady state nominal conditions are in agreement with the
expected from design, thus getting a first assessment of the coupled
1/3D model. Results for nominal condition were compared with
those obtained with a previous 1/3D single-phase model getting more
realistic temperature patterns, also allowing visualize low values of
void fraction inside the upper plenum. It must be mentioned that the
current results were obtained by imposing prescribed fission power
functions from literature. Therefore, results are showed with the aim
of point out the potentiality of the developed model.
Abstract: This paper is meant to analyze the ranking of
University of Malaysia Terengganu, UMT’s website in the World
Wide Web. There are only few researches have been done on
comparing the ranking of universities’ websites so this research will
be able to determine whether the existing UMT’s website is serving
its purpose which is to introduce UMT to the world. The ranking is
based on hub and authority values which are accordance to the
structure of the website. These values are computed using two websearching
algorithms, HITS and SALSA. Three other universities’
websites are used as the benchmarks which are UM, Harvard and
Stanford. The result is clearly showing that more work has to be done
on the existing UMT’s website where important pages according to
the benchmarks, do not exist in UMT’s pages. The ranking of UMT’s
website will act as a guideline for the web-developer to develop a
more efficient website.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.
Abstract: This study was conducted to investigate the
psychological variables motivating sport participation and
involvement among student-athletes of tertiary institutions in southwest
Nigeria. One thousand three hundred and fifty (N-1350) studentathletes
were randomly selected in all sports from nine tertiary
institutions in south-west Nigeria. These tertiary institutions include
University of Lagos, Lagos State University, Obafemi Awolowo
University, Osun State University, University of Ibadan, University
of Agriculture Abeokuta, Federal University of Technology
Akungba, University of Ilorin, and Kwara State University. The
descriptive survey research method was adopted while a self
developed validated Likert type questionnaire named Sport
Participation Scale (SPS) was used to elicit opinion from
respondents. The test-retest reliability value obtained for the
instrument, using Pearson Product Moment Correlation Co-efficient
was 0.96. Out of the one thousand three hundred and fifty (N-1350)
questionnaire administered, only one thousand two hundred and five
(N-1286) were correctly filled, coded and analysed using inferential
statistics of Chi-Square (X2) while all the tested hypotheses were set
at. 05 alpha level. Based on the findings of this study, the result
revealed that several psychological factors influence student athletes
to continue participation in sport one which includes love for the
game, famous athletes as role model and family support. However,
the analysis further revealed that the stipends the student-athletes get
from their universities have no influence on their participation and
involvement in sport.
Abstract: In this paper genetic based test data compression is
targeted for improving the compression ratio and for reducing the
computation time. The genetic algorithm is based on extended pattern
run-length coding. The test set contains a large number of X value
that can be effectively exploited to improve the test data
compression. In this coding method, a reference pattern is set and its
compatibility is checked. For this process, a genetic algorithm is
proposed to reduce the computation time of encoding algorithm. This
coding technique encodes the 2n compatible pattern or the inversely
compatible pattern into a single test data segment or multiple test data
segment. The experimental result shows that the compression ratio
and computation time is reduced.
Abstract: In this glasshouse study, we developed a new imagebased
non-destructive technique for detecting leaf P status of
different crops such as cotton, tomato and lettuce. The plants were
grown on a nutrient solution containing different P concentrations,
e.g. 0%, 50% and 100% of recommended P concentration (P0 = no P,
L; P1 = 2.5 mL 10 L-1 of P and P2 = 5 mL 10 L-1 of P). After 7 weeks
of treatment, the plants were harvested and data on leaf P contents
were collected using the standard destructive laboratory method and
at the same time leaf images were collected by a handheld crop image
sensor. We calculated leaf area, leaf perimeter and RGB (red, green
and blue) values of these images. These data were further used in
linear discriminant analysis (LDA) to estimate leaf P contents, which
successfully classified these plants on the basis of leaf P contents.
The data indicated that P deficiency in crop plants can be predicted
using leaf image and morphological data. Our proposed nondestructive
imaging method is precise in estimating P requirements of
different crop species.
Abstract: In this study, we investigated numerically heat
transfer by mixed convection coupled to radiation in a square cavity;
the upper horizontal wall is movable. The purpose of this study is to
see the influence of the emissivity ε and the varying of the
Richardson number Ri on the variation of average Nusselt number
Nu. The vertical walls of the cavity are differentially heated, the left
wall is maintained at a uniform temperature higher than the right
wall, and the two horizontal walls are adiabatic. The finite volume
method is used for solving the dimensionless Governing Equations.
Emissivity values used in this study are ranged between 0 and 1, the
Richardson number in the range 0.1 to 10. The Rayleigh number is
fixed to Ra=104 and the Prandtl number is maintained constant
Pr=0.71. Streamlines, isothermal lines and the average Nusselt
number are presented according to the surface emissivity. The results
of this study show that the Richardson number Ri and emissivity ε
affect the average Nusselt number.
Abstract: Hypertension is a common condition causing cardio
and cerebrovascular complications. Portugal has one of the highest
mortality rates from stroke and a high prevalence of hypertension.
Systolic Blood Pressure (SBP) is an important risk factor for
cardiovascular events (myocardial infarction and stroke) and
premature mortality, particularly in the elderly population. The
present study aims to estimate the prevalence of hypertension in a
Portuguese population living in a coastal city and to identify some of
its determinants (namely gender, age, the body mass index and
physical activity frequency). A total of 91 adults who attended three pharmacies of a coastal
city in the center of Portugal, between May and August of 2013 were
evaluated. Attendants who reported to have diabetes or taking
antihypertensive drugs in the 2 previous weeks were excluded from
the study. Sociodemographic factors, BMI, habits of exercise and BP
were assessed. Hypertension was defined as blood pressure ≥140/90
mmHg. The majority of the studied population was constituted by women
(75.8%), with a mean age of 54.2±1.6 years old, married or living in
civil union and that had completed secondary school or had higher
education (40%). They presented a mean BMI of 26.2±4.76 Kg/m2.,
and were sedentary. The mean BP was 127.0±17.77mmHg- 74.69 ±
9.53. In this population we found 4.3% of people with hypertension
and 16.1% with normal high blood pressure. Men exhibit a tendency to present higher systolic blood pressure
values than women. Of all the factors considered, SBP values also
tended to be higher with age and higher BMI values.
Despite the fact that the mean values of SBP did not present values
higher than 140 mmHg we must be concerned because the studied
population is undiagnosed for hypertension. Although this is a preliminary study, it might be a prelude to the
upcoming research about the underlying factors responsible for the
occurrence of SBP.
Abstract: Presently various computational techniques are used
in modeling and analyzing environmental engineering data. In the
present study, an intra-comparison of polynomial and radial basis
kernel functions based on Support Vector Regression and, in turn, an
inter-comparison with Multi Linear Regression has been attempted in
modeling mass transfer capacity of vertical (θ = 90O) and inclined (θ
multiple plunging jets (varying from 1 to 16 numbers). The data set
used in this study consists of four input parameters with a total of
eighty eight cases, forty four each for vertical and inclined multiple
plunging jets. For testing, tenfold cross validation was used.
Correlation coefficient values of 0.971 and 0.981 along with
corresponding root mean square error values of 0.0025 and 0.0020
were achieved by using polynomial and radial basis kernel functions
based Support Vector Regression respectively. An intra-comparison
suggests improved performance by radial basis function in
comparison to polynomial kernel based Support Vector Regression.
Further, an inter-comparison with Multi Linear Regression
(correlation coefficient = 0.973 and root mean square error = 0.0024)
reveals that radial basis kernel functions based Support Vector
Regression performs better in modeling and estimating mass transfer
by multiple plunging jets.
Abstract: An early diagnosis of bone metastasis is very
important for making a right decision on a subsequent therapy. One
of the most important steps to be taken initially, for developing a new
radiopharmaceutical is the measurement of organ radiation exposure
dose. In this study, the dosimetric studies of a novel agent for
SPECT-imaging of the bone metastasis, 111In-(4-
{[(bis(phosphonomethyl))carbamoyl]methyl}7,10bis(carboxymethyl)
-1,4,7,10-tetraazacyclododec-1-yl) acetic acid (111In-BPAMD)
complex, have been carried out to estimate the dose in human organs
based on the data derived from mice. The radiolabeled complex was
prepared with high radiochemical purity in the optimal conditions.
Biodistribution studies of the complex was investigated in the male
Syrian mice at the selected times after injection (2, 4, 24 and 48 h).
The human absorbed dose estimation of the complex was made based
on data derived from the mice by the radiation absorbed dose
assessment resource (RADAR) method. 111In-BPAMD complex was prepared with high radiochemical
purity >95% (ITLC) and specific activities of 2.85 TBq/mmol. Total
body effective absorbed dose for 111In-BPAMD was 0.205
mSv/MBq. This value is comparable to the other 111In clinically used
complexes. The results show that the dose with respect to the critical
organs is satisfactory within the acceptable range for diagnostic
nuclear medicine procedures. Generally, 111In-BPAMD has
interesting characteristics and it can be considered as a viable agent
for SPECT-imaging of the bone metastasis in the near future.
Abstract: A clay soil classified as A-7-6 and CH soil according
to AASHTO and unified soil classification system respectively, was
stabilized using A-3 soil (AASHTO soil classification system). The
clay soil was replaced with 0%, 10%, 20%, to 100% A-3 soil,
compacted at both British Standard Light (BSL) and British Standard
Heavy (BSH) compaction energy levels and using Unconfined
Compressive Strength (UCS) as evaluation criteria. The Maximum
Dry Density (MDD) of the treated soils at both the BSL and BSH
compaction energy levels showed increase from 0% to 40% A-3 soil
replacement after which the values reduced to 100% replacement.
The trend of the Optimum Moisture Content (OMC) with varied A-3
soil replacement was similar to that of MDD but in a reversed order.
The OMC reduced from 0% to 40% A-3 soil replacement after which
the values increased to 100% replacement. This trend was attributed
to the observed reduction in void ratio from 0% to 40% replacement
after which the void ratio increased to 100% replacement. The
maximum UCS for the soil at varied A-3 soil replacement increased
from 272 and 770 kN/m2 for BSL and BSH compaction energy level
at 0% replacement to 295 and 795 kN/m2 for BSL and BSH
compaction energy level respectively at 10% replacement after which
the values reduced to 22 and 60 kN/m2 for BSL and BSH compaction
energy level respectively at 70% replacement. Beyond 70%
replacement, the mixtures could not be moulded for UCS test.
Abstract: The goal of this paper is proposing a supply chain
value dashboard in home appliance manufacturing firms to create
more value for all stakeholders via balanced scorecard approach.
Balanced scorecard is an effective approach that managers have used
to evaluate supply chain performance in many fields but there is a
lack of enough attention to all supply chain stakeholders, improving
value creation and, defining correlation between value indicators and
performance measuring quantitatively. In this research the key
stakeholders in home appliance supply chain, value indicators with
respect to create more value for stakeholders and the most important
metrics to evaluate supply chain value performance based on
balanced scorecard approach have been selected via literature review.
The most important indicators based on expert’s judgment acquired
by in survey focused on creating more value for. Structural equation
modelling has been used to disclose relations between value
indicators and balanced scorecard metrics. The important result of
this research is identifying effective value dashboard to create more
value for all stakeholders in supply chain via balanced scorecard
approach and based on an empirical study covering ten home
appliance manufacturing firms in Iran. Home appliance
manufacturing firms can increase their stakeholder's satisfaction by
using this value dashboard.
Abstract: The use of wireless technology in industrial networks
has gained vast attraction in recent years. In this paper, we have
thoroughly analyzed the effect of contention window (CW) size on
the performance of IEEE 802.11-based industrial wireless networks
(IWN), from delay and reliability perspective. Results show that the
default values of CWmin, CWmax, and retry limit (RL) are far from
the optimum performance due to the industrial application
characteristics, including short packet and noisy environment. In this
paper, an adaptive CW algorithm (payload-dependent) has been
proposed to minimize the average delay. Finally a simple, but
effective CW and RL setting has been proposed for industrial
applications which outperforms the minimum-average-delay solution
from maximum delay and jitter perspective, at the cost of a little
higher average delay. Simulation results show an improvement of up
to 20%, 25%, and 30% in average delay, maximum delay and jitter
respectively.
Abstract: Abstract—[Tris (1,10-phenanthroline) lanthanum(III)]
trithiocyanate is a new compound that has shown high ability for
stopping the synthesis of DNA and also acting as a photosensitizer.
Nowadays, the radiation dose assessment resource (RADAR) method
is known as the most common method for absorbed dose calculation.
177Lu was produced by (n, gamma) reaction in a research reactor.
177Lu-PL3 was prepared in the optimized condition. The
radiochemical yield was checked by ITLC method. The
biodistribution of the complex was investigated by intravenously
injection to wild-type rats via their tail veins. In this study, the
absorbed dose of 177Lu-PL3 to human organs was estimated by
RADAR method. 177Lu was prepared with a specific activity of 2.6-3
GBq.mg-1 and radionuclide purity of 99.98 %. Final preparation of
the radiolabelled complex showed high radiochemical purity of >
99%. The results show that liver and spleen have received the highest
absorbed dose of 1.051 and 0.441 mSv/MBq, respectively. The
absorbed dose values for these two dose-limiting tissues suggest
more biological studies special in tumor-bearing animals.
Abstract: The measurement of organ radiation exposure dose is
one of the most important steps to be taken initially, for developing a
new radiopharmaceutical. In this study, the dosimetric studies of a
novel agent for SPECT-imaging of the bone metastasis, 111In-
1,4,7,10-tetraazacyclododecane-1,4,7,10 tetraethylene phosphonic
acid (111In-DOTMP) complex, have been carried out to estimate the
dose in human organs based on the data derived from rats. The
radiolabeled complex was prepared with high radiochemical purity in
the optimal conditions. Biodistribution studies of the complex was
investigated in the male Syrian rats at selected times after injection
(2, 4, 24 and 48 h). The human absorbed dose estimation of the
complex was made based on data derived from the rats by the
radiation absorbed dose assessment resource (RADAR) method.
111In-DOTMP complex was prepared with high radiochemical purity
of >99% (ITLC). Total body effective absorbed dose for 111In-
DOTMP was 0.061 mSv/MBq. This value is comparable to the other
111In clinically used complexes. The results show that the dose with
respect to the critical organs is satisfactory within the acceptable
range for diagnostic nuclear medicine procedures. Generally, 111In-
DOTMP has interesting characteristics and can be considered as a
viable agent for SPECT-imaging of the bone metastasis in the near
future.
Abstract: Parboiled rice was developed to produce rice, which
has a low glycemic index for diabetics. However, diabetics also have
a chromium (Cr) deficiency. Thus, it is important to fortify rice with
Cr to increase the Cr content. Moreover, parboiled rice becomes
rancid easily and has a musty odor, rendering the rice unfavorable.
Natural herbs such as pandan leaves (Pandanus amaryllifolius
Roxb.), bay leaves (Syzygium polyanthum [Wigh] Walp) and
cinnamon bark powder (Cinnamomon cassia) are commonly added to
food as aroma enhancers. Previous research has shown that these
herbs could improve insulin sensitivity. The purpose of this study
was to evaluate the effect of herbal extract coatings on the cooking
quality and the preference level of chromium fortified - parboiled rice
(CFPR). The rice grain variety used for this experiment was Ciherang
and the fortificant was CrCl3. The three herbal extracts used for
coating the CFPR were cinnamon, pandan and bay leaf, with
concentration variations of 3%, 6%, and 9% (w/w) for each of the
extracts. The samples were analyzed for their alkali spreading value,
cooking time, elongation, water uptake ratio, solid loss, colour and
lightness; and their sensory properties were determined by means of
an organoleptic test. The research showed that coating the CFPR with
pandan and cinnamon extracts at a concentration of 3% each
produced a preferred CFPR. When coated with those herbal extracts
the CFPR had the following cooking quality properties: alkali
spreading value 5 (intermediate gelatinization temperature), cooking
time, 26-27 min, color value, 14.95-15.00, lightness, 42.30 – 44.06,
elongation, 1.53 – 1.54, water uptake ratio , 4.05-4.06, and solid loss,
0.09/100 g – 0.13 g/100 g.
Abstract: The noise is one of the negative elements which
affects the human health. This article presents the measurement of
emitted noise by road vehicle and its parts during the operation.
Measurement was done in the interior of common passenger cars
with a digital sound meter. The results compare the noise value in
different cars with different body shape, which influences the driver’s
health. Transport has considerable ecological effects; many of them
are detrimental to environmental sustainability. Roads and traffic
exert a variety of direct and mostly detrimental effects on nature.
Abstract: The aim of this study is to identify the suitability of
Virtual Learning Environment (VLE) in welding simulator
application towards Computer-Based Training (CBT) in developing
skills upon new students at the Advanced Technology Training
Center (ADTEC) Batu Pahat, Johor, Malaysia and GIATMARA,
Batu Pahat, Johor, Malaysia. The significance of the study is to create
a computer-based skills development approach in welding technology
among new students in ADTEC and GIATMARA as well as to
cultivate the elements of general skills among them. This study is
also important in elevating the number of individual knowledge
workers (K-workers) working in manufacturing industry in order to
achieve a national vision which is to be an industrial nation in the
year of 2020. The design of the study is a survey type of research
which using questionnaires as the instruments and some 136 students
from ADTEC and GIATMARA were interviewed. Descriptive
analysis is used to identify the frequency and mean values. The
findings of the study show that the welding technology has developed
skills in the students because of the application of VLE simulated at a
high level and the respondents agreed that the skills could be
embedded through the application of the VLE simulator. In summary,
the VLE simulator is suitable in welding skills development training
in terms of exposing new students with the relevant characteristics of
welding skills and at the same time spurring the students’ interest
towards learning more about the skills.
Abstract: This study focuses on the hydro-geology and chemical
constituents analysis of Ikogosi Warm Spring waters in South West
Nigeria. Ikogosi warm spring is a global tourist attraction because it
has both warm and cold spring sources. Water samples from the cold
spring, warm spring and the meeting point were collected, analyzed
and the result shows close similarity in temperature, hydrogen iron
concentration (pH), alkalinity, hardness, Calcium, Magnesium,
Sodium, Iron, total dissolved solid and heavy metals. The measured
parameters in the water samples are within World Health
Organisation standards for fresh water. The study of the geology of
the warm spring reveals that the study area is underlain by a group of
slightly migmatised to non-migmatised paraschists and meta-igneous
rocks. Also, concentration levels of selected heavy metals, (Copper,
Cadmium, Zinc, Arsenic and Cromium) were determined in the water
(ppm) samples. Chromium had the highest concentration value of
1.52ppm (an average of 49.67%) and Cadmium had the lowest
concentration with value of 0.15ppm (an average of 4.89%).
Comparison of these results showed that, their mean levels are within
the standard values obtained in Nigeria. It can be concluded that both
warm and spring water are safe for drinking.