Abstract: Nano MgO has been synthesized by hydration and
dehydration method by modifies the commercial MgO. The prepared
MgO had been investigated as a heterogeneous base catalyst for
transesterification process for biodiesel production using palm oil.
TGA, FT-IR and XRD results obtained from this study lie each other
and proved in the formation of nano MgO from decomposition of
Mg(OH)2. This study proved that the prepared nano MgO was a
better base transesterification catalyst compared to commercial MgO.
The nano MgO calcined at 600ºC had gives the highest conversion of
51.3% of palm oil to biodiesel.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: In aerospace applications, interactions of airflow with
aircraft structures can result in undesirable structural deformations.
This structural deformation in turn, can be predicted if the natural
modes of the structure are known. This can be achieved through
conventional modal testing that requires a known excitation force in
order to extract these dynamic properties. This technique can be
experimentally complex because of the need for artificial excitation
and it is also does not represent actual operational condition. The
current work presents part of research work that address the practical
implementation of operational modal analysis (OMA) applied to a
cantilevered hybrid composite plate employing single contactless
sensing system via laser vibrometer. OMA technique extracts the
modal parameters based only on the measurements of the dynamic
response. The OMA results were verified with impact hammer modal
testing and good agreement was obtained.
Abstract: Equations with differentials relating to the inverse of an unknown function rather than to the unknown function itself are solved exactly for some special cases and numerically for the general case. Invertibility combined with differentiability over connected domains forces solutions always to be monotone. Numerical function inversion is key to all solution algorithms which either are of a forward type or a fixed point type considering whole approximate solution functions in each iteration. The given considerations are restricted to ordinary differential equations with inverted functions (ODEIs) of first order. Forward type computations, if applicable, admit consistency of order one and, under an additional accuracy condition, convergence of order one.
Abstract: In this paper we present modeling and simulation for
physical vapor deposition for metallic bipolar plates. In the models
we discuss the application of different models to simulate the
transport of chemical reactions of the gas species in the gas chamber.
The so called sputter process is an extremely sensitive process to
deposit thin layers to metallic plates. We have taken into account
lower order models to obtain first results with respect to the gas
fluxes and the kinetics in the chamber.
The model equations can be treated analytically in some
circumstances and complicated multi-dimensional models are solved
numerically with a software-package (UG unstructed grids, see [1]).
Because of multi-scaling and multi-physical behavior of the models,
we discuss adapted schemes to solve more accurate in the different
domains and scales. The results are discussed with physical
experiments to give a valid model for the assumed growth of thin
layers.
Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: This research aimed to study correlation between
work satisfaction and organization core value of officers in
Waterworks Authority, Bangkean Branch. Sample group of the study
was 112 officers who worked in the Waterworks Authority,
Bangkean Branch. Questionnaires were employed as a research tools,
while, Percentage, Mean, Standard Deviation, T-test, One-way
ANOVA, and Pearson Product Moment Correlation were claimed as
statistics used in this study. Researcher found that overall and
individual aspects of work satisfaction namely, work characteristic,
work progress, and colleagues significantly correlated with
organization core value in aspect of perception in choice of work at
0.5, 0.01, and 0.01 respectively. Also, such aspects were compatible
with income at .05 which indicated the low level of correlation, mid
low correlation respectively at the same direction, same direction,
opposite direction, and same direction, correspondingly.
Abstract: Defining strategic position of the organizations within
the industry environment is one of the basic and most important
phases of strategic planning to which extent that one of the
fundamental schools of strategic planning is the strategic positioning
school. In today-s knowledge-based economy and dynamic
environment, it is essential for universities as the centers of
education, knowledge creation and knowledge worker evolvement.
Till now, variant models with different approaches to strategic
positioning are deployed in defining the strategic position within the
various industries. Balanced Scorecard as one of the powerful models
for strategic positioning, analyzes all aspects of the organization
evenly. In this paper with the consideration of BSC strength in
strategic evaluation, it is used for analyzing the environmental
position of the best-s Iranian Business Schools. The results could be
used in developing strategic plans for these schools as well as other
Iranian Management and Business Schools.
Abstract: Bicycle usage for exercise, recreation, and commuting
to work in Australia shows that pedal cycling is the fourth most
popular activity with 10.6% increase in participants between 2001
and 2007. As with other means of transport, accident and injury
becomes common although mandatory bicycle helmet wearing has
been introduced. The research aims to develop a face surrogate made
of sandwich of rigid foam and rubber sheets to represent human
facial bone under blunt impact. The facial surrogate will serve as an
important test device for further development of facial-impact
protection for cyclist. A test procedure was developed to simulate the
energy of impact and record data to evaluate the effect of impact on
facial bones. Drop tests were performed to establish a suitable
combination of materials. It was found that the sandwich structure of
rigid extruded-polystyrene foam (density of 40 kg/m3 with a pattern
of 6-mm-holes), Neoprene rubber sponge, and Abrasaflex rubber
backing, had impact characteristics comparable to that of human
facial bone. In particular, the foam thickness of 30 mm and 25 mm
was found suitable to represent human zygoma (cheekbone) and
maxilla (upper-jaw bone), respectively.
Abstract: Geometry optimizations of metal complexes of Salen(bis(Salicylidene)1,2-ethylenediamine) were carried out at HF and DFT methods employing Lanl2DZ basis set. In this work structural, energies, bond lengths and other physical properties between Mn2+,Cu2+ and Ni2+ ions coordinated by salen–type ligands are examined. All calculations were performed using Gaussian 98W program series. To investigate local aromaticities, NICS were calculated at all centers of rings. The higher the band gap indicating a higher global aromaticity. The possible binding energies have been evaluated. We have evaluated Frequencies and Zero-point energy with freq calculation. The NICS(Nucleous Independent Chemical Shift) Results show Ni(II) complexes are antiaromatic and aromaticites of Mn(II) complexes are larger than Cu(II) complexes. The energy Results show Cu(II) complexes are stability than Mn(II) and Ni(II) complexes.
Abstract: In the present Jordan hotels scenario, service quality is
a vital competitive policy to keep customer support and build great
base. Hotels are trying to win customer loyalty by providing enhanced
quality services. This paper attempts to examine the impact of tourism
service quality dimension in the Jordanian five star hotels. A total of
322 surveys were administrated to tourists who were staying at three
branches Marriott hotel in Jordan. The results show that dimensions of
service quality such as empathy, reliability, responsiveness and
tangibility significantly predict customer loyalty. Specifically, among
the dimension of tourism service quality, the most significant predictor
of customer loyalty is tangibility. This paper implies that five star
hotels in Jordan should also come forward and try their best to present
better tourism service quality to win back their customers- loyalty.
Abstract: In this study is presented a general methodology to
predict the performance of a continuous near-critical fluid extraction
process to remove compounds from aqueous solutions using hollow
fiber membrane contactors. A comprehensive 2D mathematical
model was developed to study Porocritical extraction process. The
system studied in this work is a membrane based extractor of ethanol
and acetone from aqueous solutions using near-critical CO2.
Predictions of extraction percentages obtained by simulations have
been compared to the experimental values reported by Bothun et al.
[5]. Simulations of extraction percentage of ethanol and acetone
show an average difference of 9.3% and 6.5% with the experimental
data, respectively. More accurate predictions of the extraction of
acetone could be explained by a better estimation of the transport
properties in the aqueous phase that controls the extraction of this
solute.
Abstract: The mixing of pollutions and sediments in near shore regions of natural water bodies depends heavily on the characteristics such as the strength and frequency of flow instability. In the present paper, the instability of natural convection induced by absorption of solar radiation in littoral regions is considered. Spectral analysis is conducted on the quasi-steady state flow to reveal the power and frequency modes of the instability at various positions. Results indicate that the power of instability, the number of frequency modes, the prominence of higher frequency modes, and the highest frequency mode increase with the offshore distance and/or Rayleigh number. Harmonic modes are present at relatively low Rayleigh numbers. For a given offshore distance, the position with the strongest power of instability is located adjacent to the sloping bottom while the frequency modes are the same over the local depth. As the Rayleigh number increases, the unstable region extends toward the shore.
Abstract: Modern civilization has come in recent decades into a new phase in its development, called the information society. The concept of "information society" has become one of the most common. Therefore, the attempt to understand what exactly the society we live in, what are its essential features, and possible future scenarios, is important to the social and philosophical analysis. At the heart of all these deep transformations is more increasing, almost defining role knowledge and information as play substrata of «information society». The mankind opened for itself and actively exploits a new resource – information. Information society puts forward on the arena new type of the power, at the heart of which activity – mastering by a new resource: information and knowledge. The password of the new power – intelligence as synthesis of knowledge, information and communications, the strength of mind, fundamental sociocultural values. In a postindustrial society, the power of knowledge and information is crucial in the management of the company, pushing into the background the influence of money and state coercion.
Abstract: Distillation column is one of the most common
operations in process industries and is while the most expensive unit
of the amount of energy consumption. Many ideas have been
presented in the related literature for optimizing energy consumption
in distillation columns. This paper studies the different heat
integration methods in a distillation column which separate Benzene,
Toluene, Xylene, and C9+. Three schemes of heat integration
including, indirect sequence (IQ), indirect sequence with forward
energy integration (IQF), and indirect sequence with backward
energy integration (IQB) has been studied in this paper. Using
shortcut method these heat integration schemes were simulated with
Aspen HYSYS software and compared with each other with
regarding economic considerations. The result shows that the energy
consumption has been reduced 33% in IQF and 28% in IQB in
comparison with IQ scheme. Also the economic result shows that the
total annual cost has been reduced 12% in IQF and 8% in IQB
regarding with IQ scheme. Therefore, the IQF scheme is most
economic than IQB and IQ scheme.
Abstract: Today’s technology is heavily dependent on web applications. Web applications are being accepted by users at a very rapid pace. These have made our work efficient. These include webmail, online retail sale, online gaming, wikis, departure and arrival of trains and flights and list is very long. These are developed in different languages like PHP, Python, C#, ASP.NET and many more by using scripts such as HTML and JavaScript. Attackers develop tools and techniques to exploit web applications and legitimate websites. This has led to rise of web application security; which can be broadly classified into Declarative Security and Program Security. The most common attacks on the applications are by SQL Injection and XSS which give access to unauthorized users who totally damage or destroy the system. This paper presents a detailed literature description and analysis on Web Application Security, examples of attacks and steps to mitigate the vulnerabilities.
Abstract: The present paper discusses the selection of process
parameters for obtaining optimal nanocrystallites size in the CuOZrO2
catalyst. There are some parameters changing the inorganic
structure which have an influence on the role of hydrolysis and
condensation reaction. A statistical design test method is
implemented in order to optimize the experimental conditions of
CuO-ZrO2 nanoparticles preparation. This method is applied for the
experiments and L16 orthogonal array standard. The crystallites size
is considered as an index. This index will be used for the analysis in
the condition where the parameters vary. The effect of pH, H2O/
precursor molar ratio (R), time and temperature of calcination,
chelating agent and alcohol volume are particularity investigated
among all other parameters. In accordance with the results of
Taguchi, it is found that temperature has the greatest impact on the
particle size. The pH and H2O/ precursor molar ratio have low
influences as compared with temperature. The alcohol volume as
well as the time has almost no effect as compared with all other
parameters. Temperature also has an influence on the morphology
and amorphous structure of zirconia. The optimal conditions are
determined by using Taguchi method. The nanocatalyst is studied by
DTA-TG, XRD, EDS, SEM and TEM. The results of this research
indicate that it is possible to vary the structure, morphology and
properties of the sol-gel by controlling the above-mentioned
parameters.
Abstract: Kernel function, which allows the formulation of nonlinear variants of any algorithm that can be cast in terms of dot products, makes the Support Vector Machines (SVM) have been successfully applied in many fields, e.g. classification and regression. The importance of kernel has motivated many studies on its composition. It-s well-known that reproducing kernel (R.K) is a useful kernel function which possesses many properties, e.g. positive definiteness, reproducing property and composing complex R.K by simple operation. There are two popular ways to compute the R.K with explicit form. One is to construct and solve a specific differential equation with boundary value whose handicap is incapable of obtaining a unified form of R.K. The other is using a piecewise integral of the Green function associated with a differential operator L. The latter benefits the computation of a R.K with a unified explicit form and theoretical analysis, whereas there are relatively later studies and fewer practical computations. In this paper, a new algorithm for computing a R.K is presented. It can obtain the unified explicit form of R.K in general reproducing kernel Hilbert space. It avoids constructing and solving the complex differential equations manually and benefits an automatic, flexible and rigorous computation for more general RKHS. In order to validate that the R.K computed by the algorithm can be used in SVM well, some illustrative examples and a comparison between R.K and Gaussian kernel (RBF) in support vector regression are presented. The result shows that the performance of R.K is close or slightly superior to that of RBF.
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Medical images require special safety and confidentiality because critical judgment is done on the information provided by medical images. Transmission of medical image via internet or mobile phones demands strong security and copyright protection in telemedicine applications. Here, highly secured and robust watermarking technique is proposed for transmission of image data via internet and mobile phones. The Region of Interest (ROI) and Non Region of Interest (RONI) of medical image are separated. Only RONI is used for watermark embedding. This technique results in exact recovery of watermark with standard medical database images of size 512x512, giving 'correlation factor' equals to 1. The correlation factor for different attacks like noise addition, filtering, rotation and compression ranges from 0.90 to 0.95. The PSNR with weighting factor 0.02 is up to 48.53 dBs. The presented scheme is non blind and embeds hospital logo of 64x64 size.