Abstract: Any variation in environmental characteristics of
geomorphosites would lead to destabilisation of their geotouristic
values all around the planet. The Urmia lake, with an area of
approximately 5,500 km2 and a catchment area of 51,876 km2, and to
which various reasons over time, especially in the last fifty years
have seen a sharp decline and have decreased by about 93 % in two
recent decades. These variations are not only driving significant
changes in the morphology and ecology of the present lake
landscape, but at the same time are shaping newly formed
morphologies, which vanished some valuable geomorphosites or
develop into smaller geomorphosites with significant value from a
scientific and cultural point of view. This paper analyses and
discusses features and evolution in several representative coastal and
island geomorphosites. For this purpose, a total of 23 geomorphosites
were studied in two data series (1963 and 2015) and the respective
data were compared and analysed. The results showed, the total loss
in geomorphosites area in a half century amounted to a loss of more
than 90% of the valuable geomorphosites. Moreover, the comparison
between the mean yearly value of coastal area lost over the entire
period and the yearly average calculated for the shorter period (1998-
2014) clearly indicates a pattern of acceleration. This acceleration in
the rate of reduction in lake area was seen in most of the southern
half of the lake. In the region as well, the general water-level falling
is not only causing the loss of a significant water resource, which is
followed by major impact on regional ecosystems, but is also driving
the most marked recent (last century) changes in the geotouristic
landscapes. In fact, the disappearance of geomorphosites means the
loss of tourism phenomenon. In this context attention must be paid to
the question of conservation. The action needed to safeguard
geomorphosites includes: 1) Preventive action, 2) Corrective action,
and 3) Sharing knowledge.
Abstract: This paper addresses the design of hospital Intensive
Care Unit windows for the achievement of visual comfort and energy
savings. The aim was to identify the window size and shading system
configurations that could fulfill daylighting adequacy, avoid glare
and reduce energy consumption. The study focused on addressing the
effect of utilizing different shading systems in association with a
range of Window-to-Wall Ratios (WWR) in different orientations
under the desert clear-sky of Cairo, Egypt.
The results of this study demonstrated that solar penetration is a
critical concern affecting the design of ICU windows in desert
locations, as in Cairo, Egypt. Use of shading systems was found to be
essential in providing acceptable daylight performance and energy
saving. Careful positioning of the ICU window towards a proper
orientation can dramatically improve performance. It was observed
that ICU windows facing the north direction enjoyed the widest range
of successful window configuration possibilities at different WWRs.
ICU windows facing south enjoyed a reasonable number of
configuration options as well. By contrast, the ICU windows facing
the east orientation had a very limited number of options that provide
acceptable performance. These require additional local shading
measures at certain times due to glare incidence. Moreover, use of
horizontal sun breakers and solar screens to protect the ICU windows
proved to be more successful than the other alternatives in a wide
range of Window to Wall Ratios. By contrast, the use of light shelves
and vertical shading devices seemed questionable.
Abstract: Water miscible cutting fluids are conventionally used to lubricate and cool the machining zone. But issues related to health hazards, maintenance and disposal costs have limited their usage, leading to application of Minimum Quantity Lubrication (MQL). To increase the effectiveness of MQL, nanocutting fluids are proposed. In the present work, water miscible nanographite cutting fluids of varying concentration are applied at cutting zone by two systems A and B. System A utilizes high pressure air and supplies cutting fluid at a flow rate of 1ml/min. System B uses low pressure air and supplies cutting fluid at a flow rate of 5ml/min. Their performance in machining is evaluated by measuring cutting temperatures, tool wear, cutting forces and surface roughness and compared with dry machining and flood machining. Application of nanocutting fluid using both systems showed better performance than dry machining. Cutting temperatures and cutting forces obtained by both techniques are more than flood machining. But tool wear and surface roughness showed improvement compared to flood machining. Economic analysis has been carried out in all the cases to decide the applicability of the techniques.
Abstract: Super steel materials play a vital role in the
construction and fabrication of structural, piping and pipeline
components. In assuring the integrity of onshore and offshore
operating systems, they enable life cycle costs to be minimized. In
this context, Duplex stainless steel (DSS) material related welding on
constructions and fabrications plays a significant role in maintaining
and assuring integrity at an optimal expenditure over the life cycle of
production and process systems as well as associated structures. In
DSS welding, factors such as gap geometry, shielding gas supply
rate, welding current, and type of the welding process are vital to the
final joint performance. Hence, an experimental investigation has
been performed using an engineering robust design approach
(ERDA) to investigate the optimal settings that generate optimal
super DSS (i.e. UNS S32750) joint performance. This manuscript
illustrates the mathematical approach and experimental design,
optimal parameter settings and results of the verification experiment.
Abstract: The paper presents new results concerning selection of
optimal information fusion formula for ensembles of C-OTDR
channels. The goal of information fusion is to create an integral
classificator designed for effective classification of seismoacoustic
target events. The LPBoost (LP-β and LP-B variants), the Multiple
Kernel Learning, and Weighing of Inversely as Lipschitz Constants
(WILC) approaches were compared. The WILC is a brand new
approach to optimal fusion of Lipschitz Classifiers Ensembles.
Results of practical usage are presented.
Abstract: This research study aims to present a retrospective
study about speech recognition systems and artificial intelligence.
Speech recognition has become one of the widely used technologies,
as it offers great opportunity to interact and communicate with
automated machines. Precisely, it can be affirmed that speech
recognition facilitates its users and helps them to perform their daily
routine tasks, in a more convenient and effective manner. This
research intends to present the illustration of recent technological
advancements, which are associated with artificial intelligence.
Recent researches have revealed the fact that speech recognition is
found to be the utmost issue, which affects the decoding of speech. In
order to overcome these issues, different statistical models were
developed by the researchers. Some of the most prominent statistical
models include acoustic model (AM), language model (LM), lexicon
model, and hidden Markov models (HMM). The research will help in
understanding all of these statistical models of speech recognition.
Researchers have also formulated different decoding methods, which
are being utilized for realistic decoding tasks and constrained
artificial languages. These decoding methods include pattern
recognition, acoustic phonetic, and artificial intelligence. It has been
recognized that artificial intelligence is the most efficient and reliable
methods, which are being used in speech recognition.
Abstract: In this paper, a model is proposed to determine the life
distribution parameters of the useful life region for the PV system
utilizing a combination of non-parametric and linear regression
analysis for the failure data of these systems. Results showed that this
method is dependable for analyzing failure time data for such reliable
systems when the data is scarce.
Abstract: As the trend in automotive technology is fast moving
towards hybridization and electrification to curb emissions as well as
to improve the fuel efficiency, air-conditioning systems in passenger
cars have not caught up with this trend and still remain as the major
energy consumers amongst others. Adsorption based air-conditioning
systems, e.g. with silica-gel water pair, which are already in use for
residential and commercial applications, are now being considered as
a technology leap once proven feasible for the passenger cars. In this
paper we discuss a methodology, challenges and feasibility of
implementing an adsorption based air-conditioning system in a
passenger car utilizing the exhaust waste heat. We also propose an
optimized control strategy with interfaces to the engine control unit
of the vehicle for operating this system with reasonable efficiency
supported by our simulation and validation results in a prototype
vehicle, additionally comparing to existing implementations,
simulation based as well as experimental. Finally we discuss the
influence of start-stop and hybrid systems on the operation strategy of
the adsorption air-conditioning system.
Abstract: In wastewater treatment processes, aeration introduces
air into a liquid. In these systems, air is introduced by different
devices submerged in the wastewater. Smaller bubbles result in more
bubble surface area per unit of volume and higher oxygen transfer
efficiency. Jet pumps are devices that use air bubbles and are widely
used in wastewater treatment processes. The principle of jet pumps is
their ability to transfer energy of one fluid, called primary or motive,
into a secondary fluid or gas. These pumps have no moving parts and
are able to work in remote areas under extreme conditions. The
objective of this work is to study experimentally the characteristics of
the jet pump and the size of air bubbles in the laboratory water tank.
The effect of flow rate ratio on pump performance is investigated in
order to have a better understanding about pump behavior under
various conditions, in order to determine the efficiency of receiving
air bubbles different sizes. The experiments show that we should take
care when increasing the flow rate ratio while seeking to decrease
bubble size in the outlet flow. This study will help improve and
extend the use of the jet pump in many practical applications.
Abstract: Due to the continuous increment of the load demand,
identification of weaker buses, improvement of voltage profile and
power losses in the context of the voltage stability problems has
become one of the major concerns for the larger, complex,
interconnected power systems. The objective of this paper is to
review the impact of Flexible AC Transmission System (FACTS)
controller in Wind generators connected electrical network for
maintaining voltage stability. Wind energy could be the growing
renewable energy due to several advantages. The influence of wind
generators on power quality is a significant issue; non uniform power
production causes variations in system voltage and frequency.
Therefore, wind farm requires high reactive power compensation; the
advances in high power semiconducting devices have led to the
development of FACTS. The FACTS devices such as for example
SVC inject reactive power into the system which helps in maintaining
a better voltage profile. The performance is evaluated on an IEEE 14
bus system, two wind generators are connected at low voltage buses
to meet the increased load demand and SVC devices are integrated at
the buses with wind generators to keep voltage stability. Power
flows, nodal voltage magnitudes and angles of the power network are
obtained by iterative solutions using MIPOWER.
Abstract: This paper is aimed at proposing a rhombus shaped
wearable fractal antenna for wireless communication systems. The
geometrical descriptors of the antenna have been obtained using
bacterial foraging optimization (BFO) for wide band operation. The
method of moment based IE3D software has been used to simulate
the antenna and observed that miniaturization of 13.08% has been
achieved without degrading the resonating properties of the proposed
antenna. An analysis with different substrates has also been done in
order to evaluate the effectiveness of electrical permittivity on the
presented structure. The proposed antenna has low profile, light
weight and has successfully demonstrated wideband and multiband
characteristics for wearable electronic applications.
Abstract: In this paper the problem of the application of
temporal reasoning and case-based reasoning in intelligent decision
support systems is considered. The method of case-based reasoning
with temporal dependences for the solution of problems of real-time
diagnostics and forecasting in intelligent decision support systems is
described. This paper demonstrates how the temporal case-based
reasoning system can be used in intelligent decision support systems
of the car access control. This work was supported by RFBR.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user. This paper presents a new
semantic indexing approach of a documentary corpus. The indexing
process starts first by a term weighting phase to determine the
importance of these terms in the documents. Then the use of a
thesaurus like Wordnet allows moving to the conceptual level.
Each candidate concept is evaluated by determining its level of
representation of the document, that is to say, the importance of the
concept in relation to other concepts of the document. Finally, the
semantic index is constructed by attaching to each concept of the
ontology, the documents of the corpus in which these concepts are
found.
Abstract: In more complex systems, such as automotive
gearbox, a rigorous treatment of the data is necessary because there
are several moving parts (gears, bearings, shafts, etc.), and in this
way, there are several possible sources of errors and also noise. The
basic objective of this work is the detection of damage in automotive
gearbox. The detection methods used are the wavelet method, the
bispectrum; advanced filtering techniques (selective filtering) of
vibrational signals and mathematical morphology. Gearbox vibration
tests were performed (gearboxes in good condition and with defects)
of a production line of a large vehicle assembler. The vibration
signals are obtained using five accelerometers in different positions
of the sample. The results obtained using the kurtosis, bispectrum,
wavelet and mathematical morphology showed that it is possible to
identify the existence of defects in automotive gearboxes.
Abstract: High density electrical prospecting has been widely
used in groundwater investigation, civil engineering and
environmental survey. For efficient inversion, the forward modeling
routine, sensitivity calculation, and inversion algorithm must be
efficient. This paper attempts to provide a brief summary of the past
and ongoing developments of the method. It includes reviews of the
procedures used for data acquisition, processing and inversion of
electrical resistivity data based on compilation of academic literature.
In recent times there had been a significant evolution in field survey
designs and data inversion techniques for the resistivity method. In
general 2-D inversion for resistivity data is carried out using the
linearized least-square method with the local optimization technique
.Multi-electrode and multi-channel systems have made it possible to
conduct large 2-D, 3-D and even 4-D surveys efficiently to resolve
complex geological structures that were not possible with traditional
1-D surveys. 3-D surveys play an increasingly important role in very
complex areas where 2-D models suffer from artifacts due to off-line
structures. Continued developments in computation technology, as
well as fast data inversion techniques and software, have made it
possible to use optimization techniques to obtain model parameters to
a higher accuracy. A brief discussion on the limitations of the
electrical resistivity method has also been presented.
Abstract: In this study, we proposed two techniques to track the
maximum power point (MPPT) of a photovoltaic system. The first is
an intelligent control technique, and the second is robust used for
variable structure system. In fact the characteristics I-V and P–V of
the photovoltaic generator depends on the solar irradiance and
temperature. These climate changes cause the fluctuation of
maximum power point; a maximum power point tracking technique
(MPPT) is required to maximize the output power. For this we have
adopted a control by fuzzy logic (FLC) famous for its stability and
robustness. And a Siding Mode Control (SMC) widely used for
variable structure system. The system comprises a photovoltaic panel
(PV), a DC-DC converter, which is considered as an adaptation stage
between the PV and the load. The modelling and simulation of the
system is developed using MATLAB/Simulink. SMC technique
provides a good tracking speed in fast changing irradiation and when
the irradiation changes slowly or it is constant the panel power of
FLC technique presents a much smoother signal with less
fluctuations.
Abstract: An efficient remanufacturing network lead to an
efficient design of sustainable manufacturing enterprise. In
remanufacturing network, products are collected from the customer
zone, disassembled and remanufactured at a suitable remanufacturing
facility. In this respect, another issue to consider is how the returned
product to be remanufactured, in other words, what is the best layout
for such facility. In order to achieve a sustainable manufacturing
system, Cellular Manufacturing System (CMS) designs are highly
recommended, CMSs combine high throughput rates of line layouts
with the flexibility offered by functional layouts (job shop).
Introducing the CMS while designing a remanufacturing network will
benefit the utilization of such a network. This paper presents and
analyzes a comprehensive mathematical model for the design of
Dynamic Cellular Remanufacturing Systems (DCRSs). In this paper,
the proposed model is the first one to date that considers CMS and
remanufacturing system simultaneously. The proposed DCRS model
considers several manufacturing attributes such as multi period
production planning, dynamic system reconfiguration, duplicate
machines, machine capacity, available time for workers, worker
assignments, and machine procurement, where the demand is totally
satisfied from a returned product. A numerical example is presented
to illustrate the proposed model.
Abstract: The development of adaptive user interfaces (UI)
presents for a long time an important research area in which
researcher attempt to call upon the full resources and skills of several
disciplines, The adaptive UI community holds a thorough knowledge
regarding the adaptation of UIs with users and with contexts of use.
Several solutions, models, formalisms, techniques and mechanisms
were proposed to develop adaptive UI. In this paper, we propose an
approach based on the fuzzy set theory for modeling the concept of
the appropriateness of different solutions of UI adaptation with
different situations for which interactive systems have to adapt their
UIs.
Abstract: One of the key aspects of power quality improvement
in power system is the mitigation of voltage sags/swells and flicker.
Custom power devices have been known as the best tools for voltage
disturbances mitigation as well as reactive power compensation.
Dynamic Voltage Restorer (DVR) which is the most efficient and
effective modern custom power device can provide the most
commercial solution to solve several problems of power quality in
distribution networks. This paper deals with analysis and simulation
technique of DVR based on instantaneous power theory which is a
quick control to detect signals. The main purpose of this work is to
remove three important disturbances including voltage sags/swells
and flicker. Simulation of the proposed method was carried out on
two sample systems by using Matlab software environment and the
results of simulation show that the proposed method is able to
provide desirable power quality in the presence of wide range of
disturbances.
Abstract: An adaptive nonparametric method is proposed for
stable real-time detection of seismoacoustic sources in multichannel
C-OTDR systems with a significant number of channels. This
method guarantees given upper boundaries for probabilities of Type I
and Type II errors. Properties of the proposed method are rigorously
proved. The results of practical applications of the proposed method
in a real C-OTDR-system are presented in this report.