Abstract: This article is focused on the calculation of heat
radiation intensity and its optimization on an aluminum mould
surface. The inside of the mould is sprinkled with a special powder
and its outside is heated by infra heaters located above the mould
surface, up to a temperature of 250°C. By this way artificial leathers
in the car industry are produced (e. g. the artificial leather on a car
dashboard). A mathematical model of heat radiation of infra heaters
on a mould surface is described in this paper. This model allows us to
calculate a heat-intensity radiation on the mould surface for the
concrete location of infra heaters above the mould surface. It is
necessary to ensure approximately the same heat intensity radiation
on the mould surface by finding a suitable location for the infra
heaters, and in this way the same material structure and color of
artificial leather. In the model we have used a genetic algorithm to
optimize the radiation intensity on the mould surface. Experimental
measured values for the heat radiation intensity by a sensor in the
surroundings of an infra heater are used for the calculation
procedures. A computational procedure was programmed in language
Matlab.
Abstract: Distributed Power generation has gained a lot of
attention in recent times due to constraints associated with
conventional power generation and new advancements in DG
technologies .The need to operate the power system economically
and with optimum levels of reliability has further led to an increase
in interest in Distributed Generation. However it is important to place
Distributed Generator on an optimum location so that the purpose of
loss minimization and voltage regulation is dully served on the
feeder. This paper investigates the impact of DG units installation on
electric losses, reliability and voltage profile of distribution networks.
In this paper, our aim would be to find optimal distributed
generation allocation for loss reduction subjected to constraint of
voltage regulation in distribution network. The system is further
analyzed for increased levels of Reliability. Distributed Generator
offers the additional advantage of increase in reliability levels as
suggested by the improvements in various reliability indices such as
SAIDI, CAIDI and AENS. Comparative studies are performed and
related results are addressed. An analytical technique is used in order
to find the optimal location of Distributed Generator. The suggested
technique is programmed under MATLAB software. The results
clearly indicate that DG can reduce the electrical line loss while
simultaneously improving the reliability of the system.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.
Abstract: To maximise furnace production it-s necessary to
optimise furnace control, with the objectives of achieving maximum
power input into the melting process, minimum network distortion
and power-off time, without compromise on quality and safety. This
can be achieved with on the one hand by an appropriate electrode
control and on the other hand by a minimum of AC transformer
switching.
Electrical arc is a stochastic process; witch is the principal cause
of power quality problems, including voltages dips, harmonic
distortion, unbalance loads and flicker. So it is difficult to make an
appropriate model for an Electrical Arc Furnace (EAF). The factors
that effect EAF operation are the melting or refining materials,
melting stage, electrode position (arc length), electrode arm control
and short circuit power of the feeder. So arc voltages, current and
power are defined as a nonlinear function of the arc length. In this
article we propose our own empirical function of the EAF and model,
for the mean stages of the melting process, thanks to the
measurements in the steel factory.
Abstract: Bone growth factors, such as Bone Morphogenic
Protein-2 (BMP-2) have been approved by the FDA to replace grafting for some surgical interventions, but the high dose requirement limits its use in patients. Noggin, an extracellular protein, blocks the effect of BMP-2 by binding to BMP. Preventing
the BMP-2/noggin interaction will help increase the free
concentration of BMP-2 and therefore should enhance its efficacy to
induce bone formation. The work presented here involves
computational design of novel small molecule inhibitory agents of BMP-2/noggin interaction, based on our current understanding of
BMP-2, and its known putative ligands (receptors and antagonists). A
successful acquisition of such an inhibitory agent of BMP-2/noggin interaction would allow clinicians to reduce the dose required of
BMP-2 protein in clinical applications to promote osteogenesis. The
available crystal structures of the BMPs, its receptors, and the binding partner noggin were analyzed to identify the critical residues
involved in their interaction. In presenting this study, LUDI de novo design method was utilized to perform virtual screening of a large
number of compounds from a commercially available library against the binding sites of noggin to identify the lead chemical compounds
that could potentially block BMP-noggin interaction with a high specificity.
Abstract: Environmental impact assessment (EIA) is a procedure tool of environmental management for identifying, predicting, evaluating and mitigating the adverse effects of development proposals. EIA reports usually analyze how the amounts or concentrations of pollutants obey the relevant standards. Actually, many analytical tools can deepen the analysis of environmental impacts in EIA reports, such as life cycle assessment (LCA) and environmental risk assessment (ERA). Life cycle impact assessment (LCIA) is one of steps in LCA to introduce the causal relationships among environmental hazards and damage. Incorporating the LCIA concept into ERA as an integrated tool for EIA can extend the focus of the regulatory compliance of environmental impacts to determine of the significance of environmental impacts. Sometimes, when using integrated tools, it is necessary to consider fuzzy situations due to insufficient information; therefore, ERA should be generalized to fuzzy risk assessment (FRA). Finally, the use of the proposed methodology is demonstrated through the study case of the expansion plan of the world-s largest plastics processing factory.
Abstract: The range of the output power is a very important and evident limitation of two-level inverters. In order to overcome this disadvantage, multilevel inverters are introduced. Recently, Cascade H-Bridge inverters have emerged as one of the popular converter topologies used in numerous industrial applications. The modulation switching strategies such as phase shifted carrier based Pulse Width Modulation (PWM) technique and Stair case modulation with Selective Harmonic Elimination (SHE) PWM technique are generally used. NR method is used to solve highly non linear transcendental equations which are formed by SHEPWM method. Generally NR method has a drawback of requiring good initial guess but in this paper a new approach is implemented for NR method with any random initial guess. A three phase CHB 11-level inverter is chosen for analysis. MATLAB/SIMULINK programming environment and harmonic profiles are compared. Finally this paper presents a method at fundamental switching frequency with least % THDV.
Abstract: Islam has a general principle of increase in
population. But the Muslims are equally obliged to take care of
health, education and the provisions etc. for their offspring and wives
in the best possible way. The Muslims would have to regulate and
manage the number of children, if any situation affects their duties
regarding their wives or children. Islam accomplishes permissibility
of temporary blockade in human fertility if someone faces any
problem regarding health of mother or children. During the life of the
Holy Prophet (SAW), Azl (coitus interruptus) was the only way for
temporary spacing between the children. In technologically
developed environment, the same can be resort through some
advanced methodology or instrument of temporary blockade. Solid
grounds are available in Islam that the fertility rate should be
managed if any of the aspect of human quality is being affected.
Abstract: Increase in using internet makes some problems that
one of them is "internet anxiety". Internet anxiety is a type of anxious
that people may feel during surfing internet or using internet for their
educational purpose, blogging or streaming to digital libraries. The
goal of this study is evaluating of internet anxiety among the
management students. In this research Ealy's internet anxiety
questionnaire, consists of positive and negative items, is completed
by 310 participants. According to the findings, about 64.7% of them
were equal or below to mean anxiety score (50). The distribution of
internet anxiety scores was normal and there was no meaningful
difference between men-s and women's anxiety level in this sample.
Results also showed that there is no meaningful difference of internet
anxiety level between different fields of study in Management. This
evaluation will help managers to perform gap analysis between the
existent level and the desired one. Future work would be providing
techniques for abating human anxiety while using internet via human
computer interaction techniques.
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.
Abstract: Reasonably priced and well-constructed housing must
be an integral and element supporting a healthy society. The absence
of housing everyone in society can afford negatively affects the
people's health, education, ability to get jobs, develop their
community. Without access to decent housing, economic
development, integration of immigrants and inclusiveness, the society
is negatively impacted. Canada has a sterling record in creating
housing compared to many other nations around the globe. Canadian
housing gets support from a mature and responsive mortgage network
and a top-quality construction industry as well as safe and excellent
quality building materials that are readily available. Yet 1.7 million
Canadian households occupy substandard abodes. During the past
hundred years, Canada's government has made a wide variety of
attempts to provide decent residential facilities every Canadian can
afford. Despite these laudable efforts, today Canada is left with
housing that is inadequate for many Canadians. People who own their
housing are given all kinds of privileges and perks, while people with
relatively low incomes who rent their apartments or houses are
discriminated against.
To help solve these problems, zoning that is based on an
"inclusionary" philosophy is tool developed to help provide people
the affordable residences that they need. No, thirty years after its
introduction, this type of zoning has been shown effective in helping
build and provide Canadians with a houses or apartments they can
afford to pay for. Using this form of zoning can have different results
+depending on where and how it is used. After examining Canadian
affordable housing and four American cases where this type of
zoning was enforced in the USA, this makes various
recommendations for expanding Canadians' access to housing they
can afford.
Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: Transition theory has been used to derive the elasticplastic
and transitional stresses. Results obtained have been discussed
numerically and depicted graphically. It is observed that the rotating
disk made of incompressible material with inclusion require higher
angular speed to yield at the internal surface as compared to disk
made of compressible material. It is seen that the radial and
circumferential stresses are maximum at the internal surface with and
without edge load (for flat disk). With the increase in thickness
parameter (k = 2, 4), the circumferential stress is maximum at the
external surface while the radial stress is maximum at the internal
surface. From the figures drawn the disk with exponentially varying
thickness (k = 2), high angular speed is required for initial yielding at
internal surface as compared to flat disk and exponentially varying
thickness for k = 4 onwards. It is concluded that the disk made of
isotropic compressible material is on the safer side of the design as
compared to disk made of isotropic incompressible material as it
requires higher percentage increase in an angular speed to become
fully plastic from its initial yielding.
Abstract: People from different cultures favor web pages
characterized by the values of their culture and, therefore, tend to
prefer different characteristics of a website according to their cultural
values in terms of navigation, security, product information, customer
service, shopping and design tools. For a company aiming to
globalize its market it is useful to implement country specific cultural
interfaces and different web sites for countries with different cultures.
This paper, following the conclusions proposed by two models of
Hall and Hofstede, and the studies of Marcus and Gould, defines,
through an empirical analysis, the guidelines of web design for both
the Scandinavian countries and Malaysia.
Abstract: This paper describes an automated event detection and location system for water distribution pipelines which is based upon low-cost sensor technology and signature analysis by an Artificial
Neural Network (ANN). The development of a low cost failure sensor which measures the opacity or cloudiness of the local water
flow has been designed, developed and validated, and an ANN based system is then described which uses time series data produced by
sensors to construct an empirical model for time series prediction and
classification of events. These two components have been installed,
tested and verified in an experimental site in a UK water distribution
system. Verification of the system has been achieved from a series of
simulated burst trials which have provided real data sets. It is concluded that the system has potential in water distribution network
management.
Abstract: The Learning Management Systems present learning
environment which offers a collection of e-learning tools in a
package that allows a common interface and information sharing
among the tools. South East European University initial experience
in LMS was with the usage of the commercial LMS-ANGEL. After a
three year experience on ANGEL usage because of expenses that
were very high it was decided to develop our own software. As part
of the research project team for the in-house design and development
of the new LMS, we primarily had to select the features that would
cover our needs and also comply with the actual trends in the area of
software development, and then design and develop the system. In
this paper we present the process of LMS in-house development for
South East European University, its architecture, conception and
strengths with a special accent on the process of migration and
integration with other enterprise applications.
Abstract: Data compression is used operationally to reduce bandwidth and storage requirements. An efficient method for achieving lossless weather radar data compression is presented. The characteristics of the data are taken into account and the optical linear prediction is used for the PPI images in the weather radar data in the proposed method. The next PPI image is identical to the current one and a dramatic reduction in source entropy is achieved by using the prediction algorithm. Some lossless compression methods are used to compress the predicted data. Experimental results show that for the weather radar data, the method proposed in this paper outperforms the other methods.
Abstract: This paper presents a design method of self-tuning
Quantitative Feedback Theory (QFT) by using improved deadbeat
control algorithm. QFT is a technique to achieve robust control with
pre-defined specifications whereas deadbeat is an algorithm that
could bring the output to steady state with minimum step size.
Nevertheless, usually there are large peaks in the deadbeat response.
By integrating QFT specifications into deadbeat algorithm, the large
peaks could be tolerated. On the other hand, emerging QFT with
adaptive element will produce a robust controller with wider
coverage of uncertainty. By combining QFT-based deadbeat
algorithm and adaptive element, superior controller that is called selftuning
QFT-based deadbeat controller could be achieved. The output
response that is fast, robust and adaptive is expected. Using a grain
dryer plant model as a pilot case-study, the performance of the
proposed method has been evaluated and analyzed. Grain drying
process is very complex with highly nonlinear behaviour, long delay,
affected by environmental changes and affected by disturbances.
Performance comparisons have been performed between the
proposed self-tuning QFT-based deadbeat, standard QFT and
standard dead-beat controllers. The efficiency of the self-tuning QFTbased
dead-beat controller has been proven from the tests results in
terms of controller’s parameters are updated online, less percentage
of overshoot and settling time especially when there are variations in
the plant.
Abstract: The present study has been taken to explore the
screening of in vitro antimicrobial activities of D-galactose-binding
sponge lectin (HOL-30). HOL-30 was purified from the marine
demosponge Halichondria okadai by affinity chromatography. The
molecular mass of the lectin was determined to be 30 kDa with a
single polypeptide by SDS-PAGE under non-reducing and reducing
conditions. HOL-30 agglutinated trypsinized and glutaraldehydefixed
rabbit and human erythrocytes with preference for type O
erythrocytes. The lectin was subjected to evaluation for inhibition of
microbial growth by the disc diffusion method against eleven human
pathogenic gram-positive and gram-negative bacteria. The lectin
exhibited strong antibacterial activity against gram-positive bacteria,
such as Bacillus megaterium and Bacillus subtilis. However, it did
not affect against gram-negative bacteria such as Salmonella typhi
and Escherichia coli. The largest zone of inhibition was recorded of
Bacillus megaterium (12 in diameter) and Bacillus subtilis (10 mm in
diameter) at a concentration of the lectin (250 μg/disc). On the other
hand, the antifungal activity of the lectin was investigated against six
phytopathogenic fungi based on food poisoning technique. The lectin
has shown maximum inhibition (22.83%) of mycelial growth of
Botrydiplodia theobromae at a concentration of 100 μg/mL media.
These findings indicate that the lectin may be of importance to
clinical microbiology and have therapeutic applications.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.