Abstract: An active suspension system has been proposed to
improve the ride comfort. A quarter-car 2 degree-of-freedom (DOF)
system is designed and constructed on the basis of the concept of a
four-wheel independent suspension to simulate the actions of an
active vehicle suspension system. The purpose of a suspension
system is to support the vehicle body and increase ride comfort. The
aim of the work described in the paper was to illustrate the
application of fuzzy logic technique to the control of a continuously
damping automotive suspension system. The ride comfort is
improved by means of the reduction of the body acceleration caused
by the car body when road disturbances from smooth road and real
road roughness.
The paper describes also the model and controller used in the
study and discusses the vehicle response results obtained from a
range of road input simulations. In the conclusion, a comparison of
active suspension fuzzy control and Proportional Integration
derivative (PID) control is shown using MATLAB simulations.
Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: This paper describes a feasibility study that is
included with the research, development and testing of a micro
communications sonobuoy deployable by Maritime Fixed wing
Unmanned Aerial Vehicles (M-UAV) and rotor wing Quad Copters
which are both currently being developed by the University of
Adelaide. The micro communications sonobuoy is developed to act
as a seamless communication relay between an Autonomous
Underwater Vehicle (AUV) and an above water human operator
some distance away. Development of such a device would eliminate
the requirement of physical communication tethers attached to
submersible vehicles for control and data retrieval.
Abstract: This preliminary study attempts to see if a learning
environment influences instructor’s teaching strategies and learners’
in-class activities in a foreign language class at a university in Japan.
The class under study was conducted in a computer room, while the
majority of classes of the same course were offered in traditional
classrooms without computers. The study also sees if the unplanned
blended learning environment, enhanced, or worked against, in
achieving course goals, by paying close attention to in-class artefacts,
such as computers. In the macro-level analysis, the course syllabus
and weekly itinerary of the course were looked at; and in the microlevel
analysis, nonhuman actors in their environments were named
and analyzed to see how they influenced the learners’ task processes.
The result indicated that students were heavily influenced by the
presence of computers, which lead them to disregard some aspects of
intended learning objectives.
Abstract: Indigenous Knowledge (IK) has many social and
economic benefits. However, IK is at the risk of extinction due to the
difficulties to preserve it as most of the IK largely remains
undocumented. This study aims to design a model of the factors
affecting the adoption of Information and Communication
Technologies (ICTs) for the preservation of IK. The proposed model
is based on theoretical frameworks on ICT adoption. It was designed
following a literature review of ICT adoption theories for households,
and of the factors affecting ICT adoption for IK. The theory that
fitted to the best all factors was then chosen as the basis for the
proposed model. This study found that the Model of Adoption of
Technology in Households (MATH) is the most suitable theoretical
framework for modeling ICT adoption factors for the preservation of
IK.
Abstract: In this paper the Differential Quadrature Method (DQM) is employed to study the coupled lateral-torsional free vibration behavior of the laminated composite beams. In such structures due to the fiber orientations in various layers, the lateral displacement leads to a twisting moment. The coupling of lateral and torsional vibrations is modeled by the bending-twisting material coupling rigidity. In the present study, in addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies of the beam. The governing differential equations of motion which form a system of three coupled PDEs are solved numerically using DQ procedure under different boundary conditions consist of the combinations of simply, clamped, free and other end conditions. The resulting natural frequencies and mode shapes for cantilever beam are compared with similar results in the literature and good agreement is achieved.
Abstract: Misalignment and unbalance are the major concerns
in rotating machinery. When the power supply to any rotating system
is cutoff, the system begins to lose the momentum gained during
sustained operation and finally comes to rest. The exact time period
from when the power is cutoff until the rotor comes to rest is called
Coast Down Time. The CDTs for different shaft cutoff speeds were
recorded at various misalignment and unbalance conditions. The
CDT reduction percentages were calculated for each fault and there
is a specific correlation between the CDT reduction percentage and
the severity of the fault. In this paper, radial basis network, a new
generation of artificial neural networks, has been successfully
incorporated for the prediction of CDT for misalignment and
unbalance conditions. Radial basis network has been found to be
successful in the prediction of CDT for mechanical faults in rotating
machinery.
Abstract: Recent articles have addressed the problem to construct the confidence intervals for the mean of a normal distribution where the parameter space is restricted, see for example Wang [Confidence intervals for the mean of a normal distribution with restricted parameter space. Journal of Statistical Computation and Simulation, Vol. 78, No. 9, 2008, 829–841.], we derived, in this paper, analytic expressions of the coverage probability and the expected length of confidence interval for the normal mean when the whole parameter space is bounded. We also construct the confidence interval for the normal variance with restricted parameter for the first time and its coverage probability and expected length are also mathematically derived. As a result, one can use these criteria to assess the confidence interval for the normal mean and variance when the parameter space is restricted without the back up from simulation experiments.
Abstract: The objective of this research seeks to transmit a distance training model to the community in the upper northeastern region. The group sampling consists of 60 community leaders in the municipality of sub-district Kumphawapi, Kumphawapi Disrict, Udonthani Province. The research tools rely on the following instruments, they are : 1) the achievement test of community leaders- training and 2) the satisfaction questionnaires of community leaders. The statistics used in data analysis takes the statistical mean, percentage, standard deviation, and statistical T-test. The resulted findings reveal : 1) the efficiency of the distance training developed by the researcher for the community leaders joining in the training received the average score between in-training and post-training period higher than the setup criterion, 2) the two groups of participants in the training achieved higher knowledge than their pre-training state, 3) the comparison of the achievements between the two group presented no different results, 4) the community leaders obtained the high-to-highest satisfaction.
Abstract: The vibrations produced by a single point defect on
various parts of the bearing under constant radial load are predicted
by using a theoretical model. The model includes variation in the
response due to the effect of bearing dimensions, rotating frequency
distribution of load. The excitation forces are generated when the
defects on the races strike to rolling elements. In case of the outer
ring defect, the pulses generated are with periodicity of outer ring
defect frequency where as for inner ring defect, the pulses are with
periodicity of inner ring defect frequency. The effort has been carried
out in preparing the physical model of the system. Different defect
frequencies are obtained and are used to find out the amplitudes of
the vibration due to excitation of the bearing parts. Increase in the
radial load or severity of the defect produces a significant change in
bearing signature characteristics.
Abstract: The objectives of this study are to determine the
effects of soil cover type on characteristics of leachates generated
from landfill lysimeters. Four lysimeters with diameter and height
of 0.15 and 3.00 m, respectively, were prepared. Three lysimeters
were filled with municipal waste and three different cover soil types
i.e. sandy loam soil, silty loam soil and clay soil while another
lysimeter was filled solely with municipal waste. The study was
conducted in the rainy season. Leachate quantities were measured
every day and leachate characteristics were determined once a week.
The cumulative leachate quantity from the lysimeter filled solely
with municipal waste was found to be around 27% higher than the
lysimeters using cover soils. There were no any differences of the
cumulative leachate amounts generated from the lysimeters using
three types of soils. The comparison of the total mass of pollutants
generated from all lysimeters showed that the lysimeter filled solely
with municipal waste generated the maximum quantities of
pollutants. Among the lysimeters using different types of soils, the
lysimeter using sandy loam soil generated the lowest amount of most
of pollutants, compared with the lysimeters using silty loam and clay
soils. It can be concluded that in term of pollutant attenuation in the
leachate, a sandy loam is the most suitable soil to be used as a cover
soil in the landfill.
Abstract: To support user mobility for a wireless network new mechanisms are needed and are fundamental, such as paging, location updating, routing, and handover. Also an important key feature is mobile QoS offered by the WATM. Several ATM network protocols should be updated to implement mobility management and to maintain the already ATM QoS over wireless ATM networks. A survey of the various schemes and types of handover is provided. Handover procedure allows guarantee the terminal connection reestablishment when it moves between areas covered by different base stations. It is useful to satisfy user radio link transfer without interrupting a connection. However, failure to offer efficient solutions will result in handover important packet loss, severe delays and degradation of QoS offered to the applications. This paper reviews the requirements, characteristics and open issues of wireless ATM, particularly with regard to handover. It introduces key aspects of WATM and mobility extensions, which are added in the fixed ATM network. We propose a flexible approach for handover management that will minimize the QoS deterioration. Functional entities of this flexible approach are discussed in order to achieve minimum impact on the connection quality when a MT crosses the BS.
Abstract: Due to the fast development of technology, the
competition of technological products is turbulent; therefore, it is
important to understand the market trend, consumers- demand and
preferences. As the smartphones are prevalent, the main purpose of
this paper is to utilize Analytic Hierarchy Process (AHP) to analyze
consumer-s purchase evaluation factors of smartphones. Through the
AHP expert questionnaire, the smartphones- main functions are
classified as “user interface", “mobile commerce functions",
“hardware and software specifications", “entertainment functions" and
“appearance and design", five aspects to analyze the weights. Then
four evaluation criteria are evaluated under each aspect to rank the
weights. Based on an analysis of data shows that consumers consider
when purchase factors are “hardware and software specifications",
“user interface", “appearance and design", “mobile commerce
functions" and “entertainment functions" in sequence. The “hardware
and software specifications" aspect obtains the weight of 33.18%; it is
the most important factor that consumers are taken into account. In
addition, the most important evaluation criteria are central processing
unit, operating system, touch screen, and battery function in sequence.
The results of the study can be adopted as reference data for mobile
phone manufacturers in the future on the design and marketing
strategy to satisfy the voice of customer.
Abstract: Successful public-private-partnership (PPP)
implementation can not be achieved without the active participation of
private sector companies. This paper examines the decision-making of
private sector companies in public works delivered by the PPP model
on the basis of social responsibility theory. It proposes that private
sector companies should indentify objectives of entering into PPP
projects, and shoulder relevant social responsibilities, while a
minimum return should also be guaranteed in their favor, so as to
compensate for their assumed risk and support them to take on
responsibilities in the future. The paper also gives a calculation
regarding the appropriate scale and reasonable degree of private sector
involvement in PPP projects through the cost-benefit analysis in a
specific case study, with the purpose to guide the private sector
companies to create a cooperation environment resembling
“symbiosis" and facilitate the smooth implementation of public works
delivered by the PPP model.
Abstract: This study aims to investigate mechanical behavior of
deep-drawn cups consisting of aluminum (A1050)/ duralumin
(A2017) multi-layered clad structures with micro- and macro-scale
functional gradients. Such multi-layered clad structures are possibly
used for a new type of crash-boxes in automobiles to effectively
absorb the impact forces generated when automobiles having
collisions. The effect of heat treatments on microstructure,
compositional gradient, micro hardness in 2 and 6-layered aluminum/
duralumin clad structures, which were fabricated by hot rolling, have
been investigated. Impact compressive behavior of deep-drawn cups
consisting of such aluminum/ duralumin clad structures has been also
investigated in terms of energy absorption and maximum force.
Deep-drawn cups consisting of 6-layerd clad structures with microand
macro-scale functional gradients exhibit superior properties in
impact compressive tests.
Abstract: This paper describes the design of a voltage based maximum power point tracker (MPPT) for photovoltaic (PV) applications. Of the various MPPT methods, the voltage based method is considered to be the simplest and cost effective. The major disadvantage of this method is that the PV array is disconnected from the load for the sampling of its open circuit voltage, which inevitably results in power loss. Another disadvantage, in case of rapid irradiance variation, is that if the duration between two successive samplings, called the sampling period, is too long there is a considerable loss. This is because the output voltage of the PV array follows the unchanged reference during one sampling period. Once a maximum power point (MPP) is tracked and a change in irradiation occurs between two successive samplings, then the new MPP is not tracked until the next sampling of the PV array voltage. This paper proposes an MPPT circuit in which the sampling interval of the PV array voltage, and the sampling period have been shortened. The sample and hold circuit has also been simplified. The proposed circuit does not utilize a microcontroller or a digital signal processor and is thus suitable for low cost and low power applications.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: A study has been carried out to determine the effect of
coating two commercial glass-ionomer cements in either petroleum
jelly or wax. After coating, specimens were stored in water for 24 or
168 hours, then the coating removed and the surface examined.
Coating in wax was found to increase the surface hardness
significantly compared with the uncoated control, whereas coating
the specimens in petroleum jelly led to only a slight increase in
surface hardness. Coating in wax led to no detectable ion release
after either 24 or 168 hours, though there was some ion release after
the coating had been removed and the specimens exposed to water
for a further 24 hours. This shows that soluble species remained in
these specimens. Overall, this study confirms the idea that immature
glass-ionomers should be protected from early exposure to moisture,
and that the protection offered by petroleum jelly is only modest.
Abstract: The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. A multi-standard design often involves extensive system level analysis and architectural partitioning, typically requiring extensive calculations. In this research, a decimation filter design tool for wireless communication standards consisting of GSM, WCDMA, WLANa, WLANb, WLANg and WiMAX is developed in MATLAB® using GUIDE environment for visual analysis. The user can select a required wireless communication standard, and obtain the corresponding multistage decimation filter implementation using this toolbox. The toolbox helps the user or design engineer to perform a quick design and analysis of decimation filter for multiple standards without doing extensive calculation of the underlying methods.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we analyzed two algorithms namely
Characterized Delay Constrained Routing (CDCR) and Optimized
Delay Constrained Routing (ODCR). The CDCR algorithm dealt an
approach for delay constrained routing that captures the trade-off
between cost minimization and risk level regarding the delay
constraint. The ODCR which uses an adaptive path weight function
together with an additional constraint imposed on the path cost, to
restrict search space and hence ODCR finds near optimal solution in
much quicker time.