Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: The main objective of this article is to present the semi-active vibration control using an electro-rheological fluid embedded sandwich structure for a cantilever beam. ER fluid is a smart material, which cause the suspended particles polarize and connect each other to form chain. The stiffness and damping coefficients of the ER fluid can be changed in 10 micro seconds; therefore, ERF is suitable to become the material embedded in the tunable vibration absorber to become a smart absorber. For the ERF smart material embedded structure, the fuzzy control law depends on the experimental expert database and the proposed self-tuning strategy. The electric field is controlled by a CRIO embedded system to implement the real application. This study investigates the different performances using the Type-1 fuzzy and interval Type-2 fuzzy controllers. The Interval type-2 fuzzy control is used to improve the modeling uncertainties for this ERF embedded shock absorber. The self-tuning vibration controllers using Type-1 and Interval Type-2 fuzzy law are implemented to the shock absorber system. Based on the resulting performance, Internal Type-2 fuzzy is better than the traditional Type-1 fuzzy control for this vibration control system.
Abstract: Increasing growth of information volume in the
internet causes an increasing need to develop new (semi)automatic
methods for retrieval of documents and ranking them according to
their relevance to the user query. In this paper, after a brief review
on ranking models, a new ontology based approach for ranking
HTML documents is proposed and evaluated in various
circumstances. Our approach is a combination of conceptual,
statistical and linguistic methods. This combination reserves the
precision of ranking without loosing the speed. Our approach
exploits natural language processing techniques for extracting
phrases and stemming words. Then an ontology based conceptual
method will be used to annotate documents and expand the query.
To expand a query the spread activation algorithm is improved so
that the expansion can be done in various aspects. The annotated
documents and the expanded query will be processed to compute
the relevance degree exploiting statistical methods. The outstanding
features of our approach are (1) combining conceptual, statistical
and linguistic features of documents, (2) expanding the query with
its related concepts before comparing to documents, (3) extracting
and using both words and phrases to compute relevance degree, (4)
improving the spread activation algorithm to do the expansion based
on weighted combination of different conceptual relationships and
(5) allowing variable document vector dimensions. A ranking
system called ORank is developed to implement and test the
proposed model. The test results will be included at the end of the
paper.
Abstract: In this communication a quantitative modeling
approach is applied to construct model for the exchange of gases
from open sewer channel to the atmosphere. The data for the
exchange of gases of the open sewer channel for the year January
1979 to December 2006 is utilized for the construction of the model.
The study reveals that stream flow of the open sewer channel
exchanges the toxic gases continuously with time varying scale. We
find that the quantitative modeling approach is more parsimonious
model for these exchanges. The usual diagnostic tests are applied for
the model adequacy. This model is beneficial for planner and
managerial bodies for the improvement of implemented policies to
overcome future environmental problems.
Abstract: Global climate change has become the preeminent
threat to human security in the 21st century. From mitigation perspective, this study aims to evaluate the performance of biogas
renewable project under clean development mechanism activities
(namely Korat-Waste-to-Energy) in Thailand and to assess local perceptions towards the significance of climate change mitigation and
sustainability of such project in their community. Questionnaire was
developed based on the national sustainable development criteria and
was distributed among systematically selected households within
project boundaries (n=260). Majority of the respondents strongly agreed with the reduction of odor problems (81%) and air pollution
(76%). However, they were unsure about greenhouse gas reduction from such project and ignorant about the key issues of climate change. A lesson learned suggested that there is a need to further
investigate the possible socio-psychological barriers may significantly shape public perception and understandings of climate
change in the local context.
Abstract: The kinematics of manipulators is a central problem in the automatic control of robot manipulators. Theoretical background for the analysis of the 5 Dof Lynx-6 educational Robot Arm kinematics is presented in this paper. The kinematics problem is defined as the transformation from the Cartesian space to the joint space and vice versa. The Denavit-Harbenterg (D-H) model of representation is used to model robot links and joints in this study. Both forward and inverse kinematics solutions for this educational manipulator are presented, An effective method is suggested to decrease multiple solutions in inverse kinematics. A visual software package, named MSG, is also developed for testing Motional Characteristics of the Lynx-6 Robot arm. The kinematics solutions of the software package were found to be identical with the robot arm-s physical motional behaviors.
Abstract: The aim of this paper is to present the kinematic
analysis and mechanism design of an assistive robotic leg for
hemiplegic and hemiparetic patients. In this work, the priority is to
design and develop the lightweight, effective and single driver
mechanism on the basis of experimental hip and knee angles- data for
walking speed of 1 km/h. A mechanism of cam-follower with three
links is suggested for this purpose. The kinematic analysis is carried
out and analysed using commercialized MATLAB software based on
the prototype-s links sizes and kinematic relationships. In order to
verify the kinematic analysis of the prototype, kinematic analysis data
are compared with the experimental data. A good agreement between
them proves that the anthropomorphic design of the lower extremity
exoskeleton follows the human walking gait.
Abstract: Despite the availability of natural disaster related time series data for last 110 years, there is no forecasting tool available to humanitarian relief organizations to determine forecasts for emergency logistics planning. This study develops a forecasting tool based on identifying probability distributions. The estimates of the parameters are used to calculate natural disaster forecasts. Further, the determination of aggregate forecasts leads to efficient pre-disaster planning. Based on the research findings, the relief agencies can optimize the various resources allocation in emergency logistics planning.
Abstract: Since 1992, year where Hugo de Garis has published
the first paper on Evolvable Hardware (EHW), a period of intense
creativity has followed. It has been actively researched, developed
and applied to various problems. Different approaches have been
proposed that created three main classifications: extrinsic, mixtrinsic
and intrinsic EHW. Each of these solutions has a real interest.
Nevertheless, although the extrinsic evolution generates some
excellent results, the intrinsic systems are not so advanced. This
paper suggests 3 possible solutions to implement the run-time
configuration intrinsic EHW system: FPGA-based Run-Time
Configuration system, JBits-based Run-Time Configuration system
and Multi-board functional-level Run-Time Configuration system.
The main characteristic of the proposed architectures is that they are
implemented on Field Programmable Gate Array. A comparison of
proposed solutions demonstrates that multi-board functional-level
run-time configuration is superior in terms of scalability, flexibility
and the implementation easiness.
Abstract: In this paper, a fibre laser at 546 nm has been studied
for a signal power of -30 dB. Er3+-doped ZBLAN fibre has been used
by upconversion pumping of a 980 nm laser diode. Gain saturation
effect has been investigated in detail. Laser performance has also been
discussed. An efficiency of 35% has been calculated with a length of 5
mm fibre laser. Results show that Er3+-doped ZBLAN is a promising
candidate for optical amplification at 546 nm.
Abstract: In this work, a radial basis function (RBF) neural network is developed for the identification of hyperbolic distributed parameter systems (DPSs). This empirical model is based only on process input-output data and used for the estimation of the controlled variables at specific locations, without the need of online solution of partial differential equations (PDEs). The nonlinear model that is obtained is suitably transformed to a nonlinear state space formulation that also takes into account the model mismatch. A stable robust control law is implemented for the attenuation of external disturbances. The proposed identification and control methodology is applied on a long duct, a common component of thermal systems, for a flow based control of temperature distribution. The closed loop performance is significantly improved in comparison to existing control methodologies.
Abstract: Effects of bio-nitrogen fertilizer (bio-N), as a partial
alternative to mineral-nitrogen fertilizer (mineral-N), on growth,
yield and yield quality of broccoli plants were investigated. Bio-N
was applied at 1, 2 or 3 doses in combination with 65% of the
recommended dose of mineral-N (bio-N1, bio-N2 or bio-N3 +
⅔mineral-N). However, 100% of the recommended dose of mineral-
N was applied as a control. Significant positive influences of the bio-
N3 + ⅔mineral-N treatment were observed on growth traits, leaf
contents of nitrogen, phosphorus, potassium, nitrate and nitrite, and
yield quality when compared to the other two combined treatments.
In contrast, there were no significant differences in these parameters
between the bio-N3 + ⅔mineral-N and the control treatments, except
for leaf contents of nitrate and nitrite. They showed lower contents in
the bio-N3 + ⅔mineral-N treatment than the control. Therefore, we
recommend using bio-N as a partial alternative to mineral-N for
healthy nutrition.
Abstract: The purpose of this research is to study motivation
factors and also to study factors relation to job performance to
compare motivation factors under the personal factor classification
such as gender, age, income, educational level, marital status, and
working duration; and to study the relationship between Motivation
Factors and Job Performance with job satisfactions. The sample
groups utilized in this research were 400 Suan Sunandha Rajabhat
University employees. This research is a quantitative research using
questionnaires as research instrument. The statistics applied for data
analysis including percentage, mean, and standard deviation. In
addition, the difference analysis was conducted by t value computing,
one-way analysis of variance and Pearson’s correlation coefficient
computing. The findings of the study results were as follows the
findings showed that the aspects of job promotion and salary were at
the moderate levels. Additionally, the findings also showed that the
motivations that affected the revenue branch chiefs’ job performance
were job security, job accomplishment, policy and management, job
promotion, and interpersonal relation.
Abstract: In the present work, the effective moisture diffusivity
and activation energy were calculated using an infinite series solution
of Fick-s diffusion equation. The results showed that increasing
drying temperature accelerated the drying process. All drying
experiments had only falling rate period. The average effective
moisture diffusivity values varied from 2.807x10-10 to 6.977x10-10m2
s_1 over the temperature and velocity range. The temperature
dependence of the effective moisture diffusivity for the thin layer
drying of the ginger slices was satisfactorily described by an
Arrhenius-type relationship with activation energy values of 19.313-
22.722 kJ.mol-1 within 40–70 °C and 0.8-3 ms-1 temperature range.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.
Abstract: A low cost Short Message System (SMS) based Home security system equipped with motion, smoke, temperature, humidity and light sensors has been studied and tested. The sensors are controlled by a microprocessor PIC 18F4520 through the SMS having password protection code for the secure operation. The user is able to switch light and the appliances and get instant feedback. Also in cases of emergencies such as fire or robbery the system will send alert message to occupant and relevant civil authorities. The operation of the home security has been tested on Vodafone- Fiji network and Digicel Fiji Network for emergency and feedback responses for 25 samples. The experiment showed that it takes about 8-10s for the security system to respond in case of emergency. It takes about 18-22s for the occupant to switch and monitor lights and appliances and then get feedback depending upon the network traffic.
Abstract: In this paper we propose a new approach for flexible document categorization according to the document type or genre instead of topic. Our approach implements two homogenous classifiers: contextual classifier and logical classifier. The contextual classifier is based on the document URL, whereas, the logical classifier use the logical structure of the document to perform the categorization. The final categorization is obtained by combining contextual and logical categorizations. In our approach, each document is assigned to all predefined categories with different membership degrees. Our experiments demonstrate that our approach is best than other genre categorization approaches.
Abstract: This paper proposes a method that discovers sequential patterns corresponding to user-s interests from sequential data. This method expresses the interests as constraint patterns. The constraint patterns can define relationships among attributes of the items composing the data. The method recursively decomposes the constraint patterns into constraint subpatterns. The method evaluates the constraint subpatterns in order to efficiently discover sequential patterns satisfying the constraint patterns. Also, this paper applies the method to the sequential data composed of stock price indexes and verifies its effectiveness through comparing it with a method without using the constraint patterns.
Abstract: Software and applications are subjected to serious and damaging security threats, these threats are increasing as a result of increased number of potential vulnerabilities. Security testing is an indispensable process to validate software security requirements and to identify security related vulnerabilities. In this paper we analyze and compare different available vulnerabilities testing techniques based on a pre defined criteria using analytical hierarchy process (AHP). We have selected five testing techniques which includes Source code analysis, Fault code injection, Robustness, Stress and Penetration testing techniques. These testing techniques have been evaluated against five criteria which include cost, thoroughness, Ease of use, effectiveness and efficiency. The outcome of the study is helpful for researchers, testers and developers to understand effectiveness of each technique in its respective domain. Also the study helps to compare the inner working of testing techniques against a selected criterion to achieve optimum testing results.