Abstract: Single Minute Exchange of Dies (SMED) mainly focuses on recognition of internal and external activities. It is concerned particularly with transferring internal activities into external ones in as many numbers as possible, by also minimizing the internal ones. The validity of the method and procedures are verified by an application a Styrofoam manufacturing process where setup times are critical for time reduction. Significant time savings have been achieved with minimum investment. Further, the issues related with employer safety and ergonomics principles during die exchange are noted.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: Entrepreneurs are important for national labour markets and economies in that they contribute significantly to economic growth as well as provide the majority of jobs and create new ones. According to the Global Entrepreneurship Monitor’s “Report on Women and Entrepreneurship”, investment in women’s entrepreneurship is an important way to exponentially increase the impact of new venture creation finding ways to empower women’s participation and success in entrepreneurship are critical for more sustainable and successful economic development. Our results confirm that they are still differences between men and women entrepreneurs The reasons seems to be the lack of specific business skills, the less extensive social network, and the lack of identification patterns among women. Those differences can be explained by the fact that women still have fewer opportunities to make a career. If this is correct, we can predict an increasing proportion of women among entrepreneurs in the next years. Concerning the development of a favorable environment for developing and enhancing women entrepreneurship activities, our results show the insertion in a network and the role of a model doubtless represent elements determining in the choice to launch an entrepreneurship activity, as well as a precious resource for the success of her company.
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: The “conveyor belt" as a product represents a
complex high performance component with a wide range of different
applications. Further development of these highly complex
components demands an integration of new technologies and new
enhanced materials. In this context nanostructured fillers appear to
have a more promising effect on the performance of the conveyor
belt composite than conventional micro-scaled fillers.
Within the project “DotTrans" nanostructured fillers, for example
silicon dioxide, are used to optimize performance parameters of
conveyor belt systems. The objective of the project includes
operating parameters like energy consumption or friction
characteristics as well as adaptive parameters like cut or wear
resistance.
Abstract: The current work focuses on rephrasing the harmful
effects of mercury that is being released from a number of sources.
Most of the sources are from the industrial waste water. Different
techniques of mercury removal have been discussed and a brief
comparison among these has been made. The experimental work has
been conducted for two most widely used methods of mercury
removal and comparison in terms of their efficiency has been made.
Abstract: It has been defined that the “network is the system".
This implies providing levels of service, reliability, predictability and
availability that are commensurate with or better than those that
individual computers provide today. To provide this requires
integrated network management for interconnected networks of
heterogeneous devices covering both the local campus. In this paper
we are addressing a framework to effectively deal with this issue. It
consists of components and interactions between them which are
required to perform the service fault management. A real-world
scenario is used to derive the requirements which have been applied
to the component identification. An analysis of existing frameworks
and approaches with respect to their applicability to the framework is
also carried out.
Abstract: Oilsands bitumen is an extremely important source of
energy for North America. However, due to the presence of large
molecules such as asphaltenes, the density and viscosity of the
bitumen recovered from these sands are much higher than those of
conventional crude oil. As a result the extracted bitumen has to be
diluted with expensive solvents, or thermochemically upgraded in
large, capital-intensive conventional upgrading facilities prior to
pipeline transport. This study demonstrates that globally abundant
natural zeolites such as clinoptilolite from Saint Clouds, New Mexico
and Ca-chabazite from Bowie, Arizona can be used as very effective
reagents for cracking and visbreaking of oilsands bitumen. Natural
zeolite cracked oilsands bitumen products are highly recoverable (up
to ~ 83%) using light hydrocarbons such as pentane, which indicates
substantial conversion of heavier fractions to lighter components.
The resultant liquid products are much less viscous, and have lighter
product distribution compared to those produced from pure thermal
treatment. These natural minerals impart similar effect on industrially
extracted Athabasca bitumen.
Abstract: Ever increasing capacities of contemporary storage devices
inspire the vision to accumulate (personal) information without
the need of deleting old data over a long time-span. Hence the target
of SemanticLIFE project is to create a Personal Information Management
system for a human lifetime data. One of the most important
characteristics of the system is its dedication to retrieve information
in a very efficient way. By adopting user demands regarding the
reduction of ambiguities, our approach aims at a user-oriented and
yet powerful enough system with a satisfactory query performance.
We introduce the query system of SemanticLIFE, the Virtual Query
System, which uses emerging Semantic Web technologies to fulfill
users- requirements.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: For lack of the visualization of the ultrasonic detection
method of partial discharge (PD), the ultrasonic detection technology
combined with the X-ray visual detection method (UXV) is proposed.
The method can conduct qualitative analysis accurately and conduct
reliable positioning diagnosis to the internal insulation defects of
GIS, and while it could make up the blindness of the X-ray visual
detection method and improve the detection rate. In this paper, an
experimental model of GIS is used as the trial platform, a variety of
insulation defects are set inside the GIS cavity. With the proposed
method, the ultrasonic method is used to conduct the preliminary
detection, and then the X-ray visual detection is used to locate and
diagnose precisely. Therefore, the proposed UXV technology is
feasible and practical.
Abstract: Artificial Intelligence based gaming is an interesting topic in the state-of-art technology. This paper presents an automation of a tradition Omani game, called Al-Hawalees. Its related issues are resolved and implemented using artificial intelligence approach. An AI approach called mini-max procedure is incorporated to make a diverse budges of the on-line gaming. If number of moves increase, time complexity will be increased in terms of propositionally. In order to tackle the time and space complexities, we have employed a back propagation neural network (BPNN) to train in off-line to make a decision for resources required to fulfill the automation of the game. We have utilized Leverberg- Marquardt training in order to get the rapid response during the gaming. A set of optimal moves is determined by the on-line back propagation training fashioned with alpha-beta pruning. The results and analyses reveal that the proposed scheme will be easily incorporated in the on-line scenario with one player against the system.
Abstract: The presented work is motivated by a French law
regarding nuclear waste management. A new conceptual Accelerator
Driven System (ADS) designed for the Minor Actinides (MA)
transmutation has been assessed by numerical simulation. The
MUltiple Spallation Target (MUST) ADS combines high thermal power (up to 1.4 GWth) and high specific power. A 30 mA and 1
GeV proton beam is divided into three secondary beams transmitted on three liquid lead-bismuth spallation targets. Neutron and thermalhydraulic
simulations have been performed with the code MURE, based on the Monte-Carlo transport code MCNPX. A methodology has been developed to define characteristic of the MUST ADS concept according to a specific transmutation scenario. The reference
scenario is based on a MA flux (neptunium, americium and curium)
providing from European Fast Reactor (EPR) and a plutonium multireprocessing
strategy is accounted for. The MUST ADS reference
concept is a sodium cooled fast reactor. The MA fuel at equilibrium is mixed with MgO inert matrix to limit the core reactivity and
improve the fuel thermal conductivity. The fuel is irradiated over five
years. Five years of cooling and two years for the fuel fabrication are
taken into account. The MUST ADS reference concept burns about 50% of the initial MA inventory during a complete cycle. In term of
mass, up to 570 kg/year are transmuted in one concept. The methodology to design the MUST ADS and to calculate fuel
composition at equilibrium is precisely described in the paper. A detailed fuel evolution analysis is performed and the reference scenario is compared to a scenario where only americium transmutation is performed.
Abstract: Springback is a significant problem in the sheet metal
forming process. When the tools are released after the stage of
forming, the product springs out, because of the action of the internal
stresses. In many cases the deviation of form is too large and the
compensation of the springback is necessary. The precise prediction
of the springback of product is increasingly significant for the design
of the tools and for compensation because of the higher ratio of the
yield stress to the elastic modulus.
The main object in this paper was to study the effect of the
anisotropy on the springback for three directions of rolling: 0°, 45°
and 90°. At the same time, we highlighted the influence of three
different metallic materials: Aluminum, Steel and Galvanized steel.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to the direction of rolling. We also showed the
role of lubrication in the reduction of the springback.
Moreover, in this work, we have studied important characteristics
in deep drawing process which is a springback. We have presented
defaults that are showed in this process and many parameters
influenced a springback.
Finally, our results works lead us to understand the influence of
grains orientation with different metallic materials on the springback
and drawing some conclusions how to concept deep drawing tools. In
addition, the conducted work represents a fundamental contribution
in the discussion the industry application.
Abstract: Traditionally, Internet has provided best-effort service to every user regardless of its requirements. However, as Internet becomes universally available, users demand more bandwidth and applications require more and more resources, and interest has developed in having the Internet provide some degree of Quality of Service. Although QoS is an important issue, the question of how it will be brought into the Internet has not been solved yet. Researches, due to the rapid advances in technology are proposing new and more desirable capabilities for the next generation of IP infrastructures. But neither all applications demand the same amount of resources, nor all users are service providers. In this way, this paper is the first of a series of papers that presents an architecture as a first step to the optimization of QoS in the Internet environment as a solution to a SMSE's problem whose objective is to provide public service to internet with certain Quality of Service expectations. The service provides new business opportunities, but also presents new challenges. We have designed and implemented a scalable service framework that supports adaptive bandwidth based on user demands, and the billing based on usage and on QoS. The developed application has been evaluated and the results show that traffic limiting works at optimum and so it does exceeding bandwidth distribution. However, some considerations are done and currently research is under way in two basic areas: (i) development and testing new transfer protocols, and (ii) developing new strategies for traffic improvements based on service differentiation.
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: Researches show that probability-statistical methods application, especially at the early stage of the aviation Gas Turbine Engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods is considered. According to the purpose of this problem training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. For GTE technical condition more adequate model making dynamics of skewness and kurtosis coefficients- changes are analysed. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows drawing conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stageby- stage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine technical condition was made.
Abstract: Isobaric vapor-liquid equilibrium measurements are reported for the binary mixtures of n-Butylamine and Triethylamine with Cumene at 97.3 kPa. The measurements have been performed using a vapor recirculating type (modified Othmer's) equilibrium still. The binary mixture of n-Butylamine + Cumene shows positive deviation from ideality. Triethylamine + Cumene mixture shows negligible deviation from ideality. None of the systems form an azeotrope. The activity coefficients have been calculated taking into consideration the vapor phase nonideality. The data satisfy the thermodynamic consistency test of Herington. The activity coefficients have been satisfactorily correlated by means of the Margules, NRTL, and Black equations. The activity coefficient values obtained by the UNIFAC model are also reported.