Abstract: Dew harvesting needs only weak investment and
exploits a free, clean and inexhaustible energy. This study aims to
measure the relative contributions of dew and rain water in the
Mediterranean Dalmatian coast and islands of Croatia and determine
whether dew water is potable. Two sites were chosen, an open site on
the coast favourable to dew formation (Zadar) and a less favourable
site in a circus of mountains in Komiža (Vis Island). Between July
1st, 2003 and October 31st, 2006, dew hasbeen daily collected on a 1
m2 tilted (30°) test dew condenser together with ordinary
meteorological data (air temperature and relative humidity, cloud
coverage, windspeed and direction). The mean yearly cumulative
dew yields were found to be 20 mm (Zadar) and 9.3 mm (Komiža ).
During the dry season (May to October), monthly cumulative dew
water yield can represent up to 38% of water collected by rain fall. In
July 2003 and 2006, dew water represented about 120% of the
monthly cumulative rain water. Dew and rain water were analyzed in
Zadar. The corresponding parameters were measured: pH, electrical
conductivity, major anions (HCO3
-, Cl-, SO4
2-
, NO3
-
, ,) and major
cations (NH4
+, Na+, K+, Ca2+, Mg2+. Both dew and rain water are in
conformity with the WHO directives for potability except Mg2+.
Using existing roofs and refurbishing the abandoned impluviums to
permit dew collection could then provide a useful supplementary
amount of water, especially during the dry season.
Abstract: In this investigation, the antibacterial effects of
ethanolic and 7:3 isopropyl –hexane mixture extracts of Zingiber
officinale were evaluated against three Gram positive bacteria, B.
cereus, S.epidermidis, S. aureus and three Gram negative bacteria, E.
coli, K.pneumonia and P.areuginosa. Utilizing paper disk diffusion
and well methods in-vitro, MIC and MBC were determined by
macrodilution. The results showed that ethanolic rhizome extract of
ginger had significantly active than Isopropyl –hexan extract. Further
work needs to be done in these extracts including fractionation to
isolate active constituents and subsequent pharmacological
evaluation.
Abstract: Linear induction motors are used in various industries
but they have some specific phenomena which are the causes for
some problems. The most important phenomenon is called end effect.
End effect decreases efficiency, power factor and output force and
unbalances the phase currents. This phenomenon is more important
in medium and high speeds machines. In this paper a factor, EEF , is
obtained by an accurate equivalent circuit model, to determine the
end effect intensity. In this way, all of effective design parameters on
end effect is described. Accuracy of this equivalent circuit model is
evaluated by two dimensional finite-element analysis using ANSYS.
The results show the accuracy of the equivalent circuit model.
Abstract: The distillation process in the general sense is a
relatively simple technique from the standpoints of its principles.
When dedicating distillation to water treatment and specifically
producing fresh water from sea, ocean and/ briny waters it is
interesting to notice that distillation has no limitations or domains of
applicability regarding the nature or the type of the feedstock water.
This is not the case however for other techniques that are
technologically quite complex, necessitate bigger capital investments
and are limited in their usability. In a previous paper we have
explored some of the effects of temperature on yield. In this paper,
we continue building onto that knowledge base and focus on the
effects of several additional engineering and design variables on
productivity.
Abstract: There are a many of needs for the development of
SiC-based hydrogen sensor for harsh environment applications. We
fabricated and investigated Pd/Ta2O5/SiC-based hydrogen sensors
with MOS capacitor structure for high temperature process monitoring
and leak detection applications in such automotive, chemical and
petroleum industries as well as direct monitoring of combustion
processes. In this work, we used silicon carbide (SiC) as a substrate to
replace silicon which operating temperatures are limited to below
200°C. Tantalum oxide was investigated as dielectric layer which has
high permeability for hydrogen gas and high dielectric permittivity,
compared with silicon dioxide or silicon nitride. Then, electrical
response properties, such as I-V curve and dependence of capacitance
on hydrogen concentrations were analyzed in the temperature ranges
of room temperature to 500°C for performance evaluation of the
sensor.
Abstract: The roll center is one of the key parameters for designing a suspension. Several driving characteristics are affected significantly by the migration of the roll center during the suspension-s motion. The strut/SLA (strut/short-long-arm) suspension, which is widely used in production cars, combines the space-saving characteristics of a MacPherson strut suspension with some of the preferred handling characteristics of an SLA suspension. In this study, a front strut/SLA suspension is modeled by ADAMS/Car software. Kinematic roll analysis is then employed to investigate how the rolling characteristics change under the wheel travel and steering input. The related parameters, including the roll center height, roll camber gain, toe change, scrub radius and wheel track width change, are analyzed and discussed. It is found that the strut/SLA suspension clearly has a higher roll center than strut and SLA suspensions do. The variations in the roll center height under roll analysis are very different as the wheel travel displacement and steering angle are added. The results of the roll camber gain, scrub radius and wheel track width change are considered satisfactory. However, the toe change is too large and needs fine-tuning through a sensitivity analysis.
Abstract: Due to rapid economic growth, Indonesia's energy needs is rapidly increasing. Indonesia-s primary energy consumption has doubled in 2007 compared to 2003. Indonesia's status change from oil net-exporter to oil net-importer country recently has increased Indonesia's concern over energy security. Due to this, oil import becomes center of attention in the dynamics of Indonesia's energy security. Conventional studies addressing Indonesia's energy security have focused on energy production sector. This study explores Indonesia-s energy security considering energy import sector by modeling and simulating Indonesia-s energy-related policies using system dynamics. Simulation result of Indonesia's energy security in 2020 in Business-As-Usual scenario shows that in term of supply demand ratio, energy security will be very high, but also it poses high dependence on energy import. The Alternative scenario result shows lower energy security in term of supply demand ratio and much lower dependence on energy import. It is also found that the Alternative scenario produce lower GDP growth.
Abstract: Stairway Ushtobin Village is one of the five villages with original and sustainable architecture in Northwest of Iran along the border of Armenia, which has been able to maintain its environment and sustainable ecosystem. Studying circulation, function and scale (grand, medium and minor) of space, ratio of full and empty spaces, number and height of stairs, ratio of compound volume to luxury spaces, openings, type of local masonry (stone, mud, wood) and form of covering elements have been carried out in four houses of this village comparatively as some samples in this article, and furthermore, this article analyzes that the architectural shapes and organic texture of the village meet the needs of cold and dry climate. Finally, some efficient plans are offered suiting the present needs of the village to have a sustainable architecture.
Abstract: This communication is intended to provide some issues for thought on the importance of implementation of Blended Learning in traditional universities, particularly in the Spanish university system. In this respect, we believe that virtual environments are likely to meet some of the needs raised by the Bologna agreement, trying to maintain the quality of teaching and at the same time taking advantage of the functionalities that virtual learning platforms offer. We are aware that an approach of learning from an open and constructivist nature in universities is a complex process that faces significant technological, administrative and human barriers. Therefore, in order to put plans in our universities, it is necessary to analyze the state of the art of some indicators relating to the use of ICT, with special attention to virtual teaching and learning, so that we can identify the main obstacles and design adaptive strategies for their full integration in the education system. Finally, we present major initiatives launched in the European and state framework for the effective implementation of new virtual environments in the area of higher education.
Abstract: We present here the results for a comparative study of
some techniques, available in the literature, related to the relevance
feedback mechanism in the case of a short-term learning. Only one
method among those considered here is belonging to the data mining
field which is the K-nearest neighbors algorithm (KNN) while the
rest of the methods is related purely to the information retrieval field
and they fall under the purview of the following three major axes:
Shifting query, Feature Weighting and the optimization of the
parameters of similarity metric. As a contribution, and in addition to
the comparative purpose, we propose a new version of the KNN
algorithm referred to as an incremental KNN which is distinct from
the original version in the sense that besides the influence of the
seeds, the rate of the actual target image is influenced also by the
images already rated. The results presented here have been obtained
after experiments conducted on the Wang database for one iteration
and utilizing color moments on the RGB space. This compact
descriptor, Color Moments, is adequate for the efficiency purposes
needed in the case of interactive systems. The results obtained allow
us to claim that the proposed algorithm proves good results; it even
outperforms a wide range of techniques available in the literature.
Abstract: Wireless Sensor Networks consist of small battery
powered devices with limited energy resources. once deployed, the
small sensor nodes are usually inaccessible to the user, and thus
replacement of the energy source is not feasible. Hence, One of the
most important issues that needs to be enhanced in order to improve
the life span of the network is energy efficiency. to overcome this
demerit many research have been done. The clustering is the one of
the representative approaches. in the clustering, the cluster heads
gather data from nodes and sending them to the base station. In this
paper, we introduce a dynamic clustering algorithm using genetic
algorithm. This algorithm takes different parameters into
consideration to increase the network lifetime. To prove efficiency of
proposed algorithm, we simulated the proposed algorithm compared
with LEACH algorithm using the matlab
Abstract: Porcine production in China represents approximately
the 50% of the worldwide pig production. Information about pig
husbandry characteristics in China and manure properties from sows
to fatteners in intensive pig farms are not broadly available for
scientific studies as it is a time consuming, expensive task and highly
inaccessible. This study provides a report about solid pig manures
(28% dry matter) in a commercial pig farm located in the peri-urban
area of Beijing as well as a general overview of the current pig
husbandry techniques including pig breeds, feeds, diseases, housing as
well as pig manure and wastewater disposal. The main results are
intended to serve as a literature source for young scientists in order to
understand the main composition of pig manures as well as to identify
the husbandry techniques applied in an intensive pig farm in Beijing.
Abstract: The learning society has currently transformed from 'wired society' to become 'mobile society' which is facilitated by wireless network. To suit to this new paradigm, m-learning was given birth and rapidly building its prospect to be included in the future curriculum. Research and studies on m-learning spruced up in numerous aspects but there is still scarcity in studies on curriculum design of m-learning. This study is a part of an ongoing bigger study probing into the m-learning curriculum for secondary schools. The paper reports on the first phase of the study which aims to probe into the needs of curriculum design for m-learning at the secondary school level and the researcher adopted the needs analysis method. Data accrued from responses on survey questionnaires based on Lickert-point scale were analyzed statistically. The findings from this preliminary study serve as a basis for m-learning curriculum development for secondary schools.
Abstract: The implementation of the new software and hardware-s technologies for tritium processing nuclear plants, and especially those with an experimental character or of new technology developments shows a coefficient of complexity due to issues raised by the implementation of the performing instrumentation and equipment into a unitary monitoring system of the nuclear technological process of tritium removal. Keeping the system-s flexibility is a demand of the nuclear experimental plants for which the change of configuration, process and parameters is something usual. The big amount of data that needs to be processed stored and accessed for real time simulation and optimization demands the achievement of the virtual technologic platform where the data acquiring, control and analysis systems of the technological process can be integrated with a developed technological monitoring system. Thus, integrated computing and monitoring systems needed for the supervising of the technological process will be executed, to be continued with the execution of optimization system, by choosing new and performed methods corresponding to the technological processes within the tritium removal processing nuclear plants. The developing software applications is executed with the support of the program packages dedicated to industrial processes and they will include acquisition and monitoring sub-modules, named “virtually" as well as the storage sub-module of the process data later required for the software of optimization and simulation of the technological process for tritium removal. The system plays and important role in the environment protection and durable development through new technologies, that is – the reduction of and fight against industrial accidents in the case of tritium processing nuclear plants. Research for monitoring optimisation of nuclear processes is also a major driving force for economic and social development.
Abstract: Today, incorrect use of lands and land use changes,
excessive grazing, no suitable using of agricultural farms, plowing on
steep slopes, road construct, building construct, mine excavation etc
have been caused increasing of soil erosion and sediment yield. For
erosion and sediment estimation one can use statistical and empirical
methods. This needs to identify land unit map and the map of
effective factors. However, these empirical methods are usually time
consuming and do not give accurate estimation of erosion. In this
study, we applied GIS techniques to estimate erosion and sediment of
Menderjan watershed at upstream Zayandehrud river in center of
Iran. Erosion faces at each land unit were defined on the basis of land
use, geology and land unit map using GIS. The UTM coordinates of
each erosion type that showed more erosion amounts such as rills and
gullies were inserted in GIS using GPS data. The frequency of
erosion indicators at each land unit, land use and their sediment yield
of these indices were calculated. Also using tendency analysis of
sediment yield changes in watershed outlet (Menderjan hydrometric
gauge station), was calculated related parameters and estimation
errors. The results of this study according to implemented watershed
management projects can be used for more rapid and more accurate
estimation of erosion than traditional methods. These results can also
be used for regional erosion assessment and can be used for remote
sensing image processing.
Abstract: Most of ignition delay correlations studies have been
developed in a constant volume bombs which cannot capture the
dynamic variation in pressure and temperature during the ignition
delay as in real engines. Watson, Assanis et. al. and Hardenberg
and Hase correlations have been developed based on experimental
data of diesel engines. However, they showed limited predictive
ability of ignition delay when compared to experimental results. The
objective of the study was to investigate the dependency of ignition
delay time on engine brake power. An experimental investigation of
the effect of automotive diesel and water diesel emulsion fuels on
ignition delay under steady state conditions of a direct injection diesel
engine was conducted. A four cylinder, direct injection naturally
aspirated diesel engine was used in this experiment over a wide range
of engine speeds and two engine loads. The ignition delay
experimental data were compared with predictions of Assanis et. al.
and Watson ignition delay correlations. The results of the
experimental investigation were then used to develop a new ignition
delay correlation. The newly developed ignition delay correlation has
shown a better agreement with the experimental data than Assanis et.
al. and Watson when using automotive diesel and water diesel
emulsion fuels especially at low to medium engine speeds at both
loads. In addition, the second derivative of cylinder pressure which is
the most widely used method in determining the start of combustion
was investigated.
Abstract: Due to memory leaks, often-valuable system memory
gets wasted and denied for other processes thereby affecting the
computational performance. If an application-s memory usage
exceeds virtual memory size, it can leads to system crash. Current
memory leak detection techniques for clusters are reactive and
display the memory leak information after the execution of the
process (they detect memory leak only after it occur).
This paper presents a Dynamic Memory Monitoring Agent
(DMMA) technique. DMMA framework is a dynamic memory leak
detection, that detects the memory leak while application is in
execution phase, when memory leak in any process in the cluster is
identified by DMMA it gives information to the end users to enable
them to take corrective actions and also DMMA submit the affected
process to healthy node in the system. Thus provides reliable service
to the user. DMMA maintains information about memory
consumption of executing processes and based on this information
and critical states, DMMA can improve reliability and
efficaciousness of cluster computing.
Abstract: This paper presents the simulation the results of
electric field and potential distributions along surface of silicone
rubber polymer insulators. Near the same leakage distance subjected
to 15 kV in 50 cycle salt fog ageing test, alternate sheds silicone
rubber polymer insulator showed better contamination performance
than straight sheds silicone rubber polymer insulator. Severe surface
ageing was observed on the straight sheds insulator. The objective of
this work is to elucidate that electric field distribution along straight
sheds insulator higher than alternate shed insulator in salt fog ageing
test. Finite element method (FEM) is adopted for this work. The
simulation results confirmed the experimental data, as well.
Abstract: Hysteresis phenomenon has been observed in the
operations of both horizontal-axis and vertical-axis wind turbines
(HAWTs and VAWTs). In this study, wind tunnel experiments were
applied to investigate the characters of hysteresis phenomena between
the angular speed and the external resistance of electrical loading
during the operation of a Darrieus type VAWT. Data of output voltage,
output current, angular speed of wind turbine under different wind
speeds are measured and analyzed. Results show that the range of
external resistance changes with the wind speed. The range decreases
as the wind speed increases following an exponential decay form.
Experiments also indicate that the maximum output power of wind
turbines is always inside the range where hysteresis happened. These
results provide an important reference to the design of output control
system of wind turbines.
Abstract: The process of wafer fabrication is arguably the most
technologically complex and capital intensive stage in semiconductor
manufacturing. This large-scale discrete-event process is highly reentrant,
and involves hundreds of machines, restrictions, and
processing steps. Therefore, production control of wafer fabrication
facilities (fab), specifically scheduling, is one of the most challenging
problems that this industry faces. Dispatching rules have been
extensively applied to the scheduling problems in semiconductor
manufacturing. Moreover, lot release policies are commonly used in
this manufacturing setting to further improve the performance of such
systems and reduce its inherent variability. In this work, simulation is
used in the scheduling of re-entrant flow shop manufacturing systems
with an application in semiconductor wafer fabrication; where, a
simulation model has been developed for the Intel Five-Machine Six
Step Mini-Fab using the ExtendTM simulation environment. The
Mini-Fab has been selected as it captures the challenges involved in
scheduling the highly re-entrant semiconductor manufacturing lines.
A number of scenarios have been developed and have been used to
evaluate the effect of different dispatching rules and lot release
policies on the selected performance measures. Results of simulation
showed that the performance of the Mini-Fab can be drastically
improved using a combination of dispatching rules and lot release
policy.