Abstract: Propylene self-metathesis to ethylene and butene was
studied over WOx/SiO2 catalysts at 450oC and atmospheric pressure.
The WOx/SiO2 catalysts were prepared by incipient wetness
impregnation of ammonium metatungstate aqueous solution. It was
found that, adding nano-sized extra supports (SiO2 and TiO2) by
physical mixing with the WOx/SiO2 enhanced propylene conversion.
The UV-Vis and FT-Raman results revealed that WOx could migrate
from the original silica support to the extra support, leading to a
better dispersion of WOx. The ICP-OES results also indicate that
WOx existed on the extra support. Coke formation was investigated
on the catalysts after 10 h time-on-stream by TPO. However, adding
nano-sized extra supports led to higher coke formation which may be
related to acidity as characterized by NH3-TPD.
Abstract: A cyclostationary Gaussian linearization method is
formulated for investigating the time average response of nonlinear
system under sinusoidal signal and white noise excitation. The
quantitative measure of cyclostationary mean, variance, spectrum of
mean amplitude, and mean power spectral density of noise are
analyzed. The qualitative response behavior of stochastic jump and
bifurcation are investigated. The validity of the present approach in
predicting the quantitative and qualitative statistical responses is
supported by utilizing Monte Carlo simulations. The present analysis
without imposing restrictive analytical conditions can be directly
derived by solving non-linear algebraic equations. The analytical
solution gives reliable quantitative and qualitative prediction of mean
and noise response for the Duffing system subjected to both sinusoidal
signal and white noise excitation.
Abstract: Exact solution of an unsteady MHD flow of elasticoviscous
fluid through a porous media in a tube of spherical cross
section under the influence of magnetic field and constant pressure
gradient has been obtained in this paper. Initially, the flow is
generated by a constant pressure gradient. After attaining the steady
state, the pressure gradient is suddenly withdrawn and the resulting
fluid motion in a tube of spherical cross section by taking into
account of the porosity factor and magnetic parameter of the
bounding surface is investigated. The problem is solved in two-stages
the first stage is a steady motion in tube under the influence of a
constant pressure gradient, the second stage concern with an unsteady
motion. The problem is solved employing separation of variables
technique. The results are expressed in terms of a non-dimensional
porosity parameter (K), magnetic parameter (m) and elasticoviscosity
parameter (β), which depends on the Non-Newtonian
coefficient. The flow parameters are found to be identical with that of
Newtonian case as elastic-viscosity parameter and magnetic
parameter tends to zero and porosity tends to infinity. It is seen that
the effect of elastico-viscosity parameter, porosity parameter and
magnetic parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: This paper provides a quantitative measure of the
time-varying multiunit neuronal spiking activity using an entropy
based approach. To verify the status embedded in the neuronal activity
of a population of neurons, the discrete wavelet transform (DWT) is
used to isolate the inherent spiking activity of MUA. Due to the
de-correlating property of DWT, the spiking activity would be
preserved while reducing the non-spiking component. By evaluating
the entropy of the wavelet coefficients of the de-noised MUA, a
multiresolution Shannon entropy (MRSE) of the MUA signal is
developed. The proposed entropy was tested in the analysis of both
simulated noisy MUA and actual MUA recorded from cortex in rodent
model. Simulation and experimental results demonstrate that the
dynamics of a population can be quantified by using the proposed
entropy.
Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: Experimental production methods of Chevreul’s salt
being an intermediate stage product in copper recovery were
investigated on this article. Chevreul’s salt, Cu2SO3.CuSO3.2H2O,
being a mixed valence copper sulphite compound, has been obtained
by using different methods and reagents. Chevreul’s salt has an
intense brick-red color. It is highly stable and expensive. The
production of Chevreul’s salt plays a key role in hydrometallurgy.
Thermodynamic tendency on precipitation of Chevreul’s salt is
related to pH and temperature. Besides, SO2 gaseous is a versatile
reagent for precipitating of copper sulphites, Using of SO2 for
selective precipitation can be made by appropriate adjustments of pH
and temperature. Chevreul’s salt does not form in acidic solutions if
those solutions contains considerable amount of sulfurous acid. It is
necessary to maintain between pH 2–4.5, because, solubility of
Chevreul’s salt increases with decreasing of pH values. Also, the
region which Chevreul’s salt is stable can be seen from the potentialpH
diagram.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: Specific leaf area (SLA; cm2leaf g-1leaf) the ratio of leaf
area to leaf dry mass is a key ecophysiological parameter influencing
leaf physiology, photosynthesis, and whole plant carbon gain and
also can be used as a rapid and diagnostic tool. In this study, two
species of soluble inorganic selenium forms, selenite (Se^IV) and
selenate (Se^VI) at different concentrations were investigated on maize
plants that were growing in nutrient solutions during 2 weeks and at
the end of the experiment, amounts of SLA for first and second
leaves of maize were measured. In accordance with the results we
observed that our regarded Se concentrations in both forms of Se^IV
and Se^VI were not effective on maize plants’ SLA significantly
although high level of 3 mg.kg-1 Se^IV had negative affect on growth
of the samples that had been treated by it but about Se^VI samples we
did not observe this state and our different considered Se^VI
concentrations were not toxic for maize plants.
Abstract: This article discusses event monitoring options for
heterogeneous event sources as they are given in nowadays
heterogeneous distributed information systems. It follows the central
assumption, that a fully generic event monitoring solution cannot
provide complete support for event monitoring; instead, event source
specific semantics such as certain event types or support for certain
event monitoring techniques have to be taken into account.
Following from this, the core result of the work presented here is
the extension of a configurable event monitoring (Web) service for a
variety of event sources. A service approach allows us to trade
genericity for the exploitation of source specific characteristics. It
thus delivers results for the areas of SOA, Web services, CEP and
EDA.
Abstract: In this study, polycaprolactone (PCL) was dissolved
in chloroform:ethanol solvent system at a concentration of 18 w/v %.
1, 2, 4, and 6 droplets of formic acid were added to the prepared 10ml
PCL-chloroform:ethanol solutions separately. Fibrous webs were
produced by electrospinning technique based on the horizontal
working principle. Morphology of the webs was investigated by
using scanning electron microscopy (SEM) whereas fiber diameters
were measured by Image J Software System. The effect of formic
acid addition to the mostly used chloroform solvent on fiber
morphology was examined.
Results indicate that there is a distinct fall in fiber diameter with
the addition of formic acid drops. The average fiber diameter was
measured as 2.22μm in PCL /chloroform:ethanol solution system. On
the other hand, 328nm and 256 nm average fiber diameters were
measured for the samples of 4 drops and 6 drops formic acid added.
This study offers alternative solvent systems to produce nanoscaled,
nontoxic PCL fibrous webs by electrospinning technique.
Abstract: In this paper, the problem of steady laminar boundary
layer flow and heat transfer over a permeable exponentially
stretching/shrinking sheet with generalized slip velocity is
considered. The similarity transformations are used to transform the
governing nonlinear partial differential equations to a system of
nonlinear ordinary differential equations. The transformed equations
are then solved numerically using the bvp4c function in MATLAB.
Dual solutions are found for a certain range of the suction and
stretching/shrinking parameters. The effects of the suction parameter,
stretching/shrinking parameter, velocity slip parameter, critical shear
rate and Prandtl number on the skin friction and heat transfer
coefficients as well as the velocity and temperature profiles are
presented and discussed.
Abstract: Co-crystal is believed to improve the solubility and
dissolution rates and thus, enhanced the bioavailability of poor water
soluble drugs particularly during the oral route of administration.
With the existing of poorly soluble drugs in pharmaceutical industry,
the screening of co-crystal formation using carbamazepine (CBZ) as
a model drug compound with dicarboxylic acids co-crystal formers
(CCF) namely fumaric (FA) and succinic (SA) acids in ethanol has
been studied. The co-crystal formations were studied by varying the
mol ratio values of CCF to CBZ to access the effect of CCF
concentration on the formation of the co-crystal. Solvent evaporation,
slurry and cooling crystallization which representing the solution
based method co-crystal screening were used. Based on the
differential scanning calorimetry (DSC) analysis, the melting point of
CBZ-SA in different ratio was in the range between 188oC-189oC.
For CBZ-FA form A and CBZ-FA form B the melting point in
different ratio were in the range of 174oC-175oC and 185oC-186oC
respectively. The product crystal from the screening was also
characterized using X-ray powder diffraction (XRPD). The XRPD
pattern profile analysis has shown that the CBZ co-crystals with FA
and SA were successfully formed for all ratios studied. The findings
revealed that CBZ-FA co-crystal were formed in two different
polymorphs. It was found that CBZ-FA form A and form B were
formed from evaporation and slurry crystallization methods
respectively. On the other hand, in cooling crystallization method,
CBZ-FA form A was formed at lower mol ratio of CCF to CBZ and
vice versa. This study disclosed that different methods and mol ratios
during the co-crystal screening can affect the outcome of co-crystal
produced such as polymorphic forms of co-crystal and thereof. Thus,
it was suggested that careful attentions is needed during the screening
since the co-crystal formation is currently one of the promising
approach to be considered in research and development for
pharmaceutical industry to improve the poorly soluble drugs.
Abstract: Gypsum (CaSO4.2H2O) is a mineral that is found in
large quantities in the Turkey and in the World. In this study, the
dissolution of this mineral in the diammonium hydrogen phosphate
solutions has been studied. The dissolution and dissolution kinetics of
gypsum in diammonium hydrogen phosphate solutions will be useful
for evaluating of solid wastes containing gypsum. Parameters such as
diammonium hydrogen phosphate concentration, temperature and
stirring speed affecting on the dissolution rate of the gypsum in
diammonium hydrogen phosphate solutions were investigated. In
experimental studies have researched effectiveness of the selected
parameters. The dissolution of gypsum were examined in two parts at
low and high temperatures. The experimental results were
successfully correlated by linear regression using Statistica program.
Dissolution curves were evaluated shrinking core models for solidfluid
systems. The activation energy was found to be 34.58 kJ/mol
and 44.45 kJ/mol for the low and the high temperatures. The
dissolution of gypsum was controlled by chemical reaction both low
temperatures and high temperatures.
Abstract: This paper introduces an original method for
guaranteed estimation of the accuracy for an ensemble of Lipschitz
classifiers. The solution was obtained as a finite closed set of
alternative hypotheses, which contains an object of classification with
probability of not less than the specified value. Thus, the
classification is represented by a set of hypothetical classes. In this
case, the smaller the cardinality of the discrete set of hypothetical
classes is, the higher is the classification accuracy. Experiments have
shown that if cardinality of the classifiers ensemble is increased then
the cardinality of this set of hypothetical classes is reduced. The
problem of the guaranteed estimation of the accuracy for an ensemble
of Lipschitz classifiers is relevant in multichannel classification of
target events in C-OTDR monitoring systems. Results of suggested
approach practical usage to accuracy control in C-OTDR monitoring
systems are present.
Abstract: An innovative concept called “Flexy-Energy” is developing at 2iE. This concept aims to produce electricity at lower cost by smartly mix different available energy sources in accordance to the load profile of the region. With a higher solar irradiation and due to the fact that Diesel generator are massively used in sub-Saharan rural areas, PV/Diesel hybrid systems could be a good application of this concept and a good solution to electrify this region, provided they are reliable, cost effective and economically attractive to investors. Presentation of the developed approach is the aims of this paper. The PV/Diesel hybrid system designed consists to produce electricity and/or heat from a coupling between Diesel Diesel generators and PV panels without batteries storage, while ensuring the substitution of gasoil by bio-fuels available in the area where the system will be installed. The optimal design of this system is based on his technical performances; the Life Cycle Cost (LCC) and Levelized Cost of Energy are developed and use as economic criteria. The Net Present Value (NPV), the internal rate of return (IRR) and the discounted payback (DPB) are also evaluated according to dual electricity pricing (in sunny and unsunny hours). The PV/Diesel hybrid system obtained is compared to the standalone Diesel Diesel generators. The approach carried out in this paper has been applied to Siby village in Mali (Latitude 12 ° 23'N 8 ° 20'W) with 295 kWh as daily demand.This approach provides optimal physical characteristics (size of the components, number of component) and dynamical characteristics in real time (number of Diesel generator on, their load rate, fuel specific consumptions, and PV penetration rate) of the system. The system obtained is slightly cost effective; but could be improved with optimized tariffing strategies.
Abstract: Nature is the immense gifted source for solving
complex problems. It always helps to find the optimal solution to
solve the problem. Mobile Ad Hoc NETwork (MANET) is a wide
research area of networks which has set of independent nodes. The
characteristics involved in MANET’s are Dynamic, does not depend
on any fixed infrastructure or centralized networks, High mobility.
The Bio-Inspired algorithms are mimics the nature for solving
optimization problems opening a new era in MANET. The typical
Swarm Intelligence (SI) algorithms are Ant Colony Optimization
(ACO), Artificial Bee Colony (ABC), Particle Swarm Optimization
(PSO), Modified Termite Algorithm, Bat Algorithm (BA), Wolf
Search Algorithm (WSA) and so on. This work mainly concentrated
on nature of MANET and behavior of nodes. Also it analyses various
performance metrics such as throughput, QoS and End-to-End delay
etc.
Abstract: Recently, the green architecture becomes a
significant way to a sustainable future. Green building designs
involve finding the balance between comfortable homebuilding and
sustainable environment. Moreover, the utilization of the new
technologies such as artificial intelligence techniques are used to
complement current practices in creating greener structures to keep
the built environment more sustainable. The most common objectives
in green buildings should be designed to minimize the overall impact
of the built environment that effect on ecosystems in general and in
particularly human health and natural environment. This will lead to
protecting occupant health, improving employee productivity,
reducing pollution and sustaining the environmental. In green
building design, multiple parameters which may be interrelated,
contradicting, vague and of qualitative/quantitative nature are
broaden to use. This paper presents a comprehensive critical state- ofart-
review of current practices based on fuzzy and its combination
techniques. Also, presented how green architecture/building can be
improved using the technologies that been used for analysis to seek
optimal green solutions strategies and models to assist in making the
best possible decision out of different alternatives.