Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: The objective of this paper is to investigate a new
approach based on the idea of pictograms for food portion size. This
approach adopts the model of the United States Pharmacopeia- Drug
Information (USP-DI). The representation of each food portion size
composed of three parts: frame, the connotation of dietary portion
sizes and layout. To investigate users- comprehension based on this
approach, two experiments were conducted, included 122 Taiwanese
people, 60 male and 62 female with ages between 16 and 64 (divided
into age groups of 16-30, 31-45 and 46-64). In Experiment 1, the mean
correcting rate of the understanding level of food items is 48.54%
(S.D.= 95.08) and the mean response time 2.89sec (S.D.=2.14). The
difference on the correct rates for different age groups is significant
(P*=0.00
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: Aquatic and semi aquatic birds as a group are suited to
feed and breed in environments in which water forms a fundamental
part. These birds are biological indicator in aquatic environment,
because these birds belong to the top level of food chain in aquatic
ecosystems. There are 61 species in 14 families of aquatic and semi
aquatic birds in Iran. The birds of the Sattarkhan Lake belong to 16
species in 8 families which include 26.2 percent of total Aquatic and
semi aquatic bird species and 57% of Aquatic and semi aquatic bird's
family of Iran. Study was carried out monthly at Sattarkhan Lake
show the existence of Phalacrocorax carbo, Ardea cinerea, Egretta
alba, Egretta garzetta, Bubulcus ibis, Botaurus stellaris, Sterna
hirundo, Chlidonias leucopterus, Larus minutus, Larus argentatus,
Larus ridibunbus, Alcedo atthis, Ciconia ciconia, Plegadis
falcinellus, Circus aeruginosus, Corvus frugilegus
Abstract: Polynomial maps offer analytical properties used to obtain better performances in the scope of chaos synchronization under noisy channels. This paper presents a new method to simplify equations of the Exact Polynomial Kalman Filter (ExPKF) given in [1]. This faster algorithm is compared to other estimators showing that performances of all considered observers vanish rapidly with the channel noise making application of chaos synchronization intractable. Simulation of ExPKF shows that saturation drawn on the emitter to keep it stable impacts badly performances for low channel noise. Then we propose a particle filter that outperforms all other Kalman structured observers in the case of noisy channels.
Abstract: Thermally insulating ceramic coatings also known as
thermal barrier coatings (TBCs) have been essential technologies to
improve the performance and efficiency of advanced gas turbines in
service at extremely high temperatures. The damage mechanisms of
air-plasma sprayed YSZ thermal barrier coatings (TBC) with various
microstructures were studied by microscopic techniques after thermal
cycling. The typical degradation of plasma TBCs that occurs during
cyclic furnace testing of an YSZ and alumina coating on a Titanium
alloy are analyzed. During the present investigation the effects of
topcoat thickness, bond coat oxidation, thermal cycle lengths and test
temperature are investigated using thermal cycling. These results
were correlated with stresses measured by a spectroscopic technique
in order to understand specific damage mechanism. The failure
mechanism of former bond coats was found to involve fracture
initiation at the thermally grown oxide (TGO) interface and at the
TGO bond coat interface. The failure mechanism of the YZ was
found to involve combination of fracture along the interface between
TGO and bond coat.
Abstract: An appropriate project delivery system (PDS) is crucial
to the success of a construction projects. Case-based Reasoning (CBR)
is a useful support for PDS selection. However, the traditional CBR
approach represents cases as attribute-value vectors without taking
relations among attributes into consideration, and could not calculate
the similarity when the structures of cases are not strictly same.
Therefore, this paper solves this problem by adopting the Relational
Case-based Reasoning (RCBR) approach for PDS selection,
considering both the structural similarity and feature similarity. To
develop the feature terms of the construction projects, the criteria and
factors governing PDS selection process are first identified. Then
feature terms for the construction projects are developed. Finally, the
mechanism of similarity calculation and a case study indicate how
RCBR works for PDS selection. The adoption of RCBR in PDS
selection expands the scope of application of traditional CBR method
and improves the accuracy of the PDS selection system.
Abstract: Segmentation, filtering out of measurement errors and
identification of breakpoints are integral parts of any analysis of
microarray data for the detection of copy number variation (CNV).
Existing algorithms designed for these tasks have had some successes
in the past, but they tend to be O(N2) in either computation time or
memory requirement, or both, and the rapid advance of microarray
resolution has practically rendered such algorithms useless. Here we
propose an algorithm, SAD, that is much faster and much less thirsty
for memory – O(N) in both computation time and memory requirement
-- and offers higher accuracy. The two key ingredients of SAD are the
fundamental assumption in statistics that measurement errors are
normally distributed and the mathematical relation that the product of
two Gaussians is another Gaussian (function). We have produced a
computer program for analyzing CNV based on SAD. In addition to
being fast and small it offers two important features: quantitative
statistics for predictions and, with only two user-decided parameters,
ease of use. Its speed shows little dependence on genomic profile.
Running on an average modern computer, it completes CNV analyses
for a 262 thousand-probe array in ~1 second and a 1.8 million-probe
array in 9 seconds
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: Soursop (Anona muricata) is one of the underutilized tropical fruits containing nutrients, particularly dietary fibre and antioxidant properties that are beneficial to human health. This objective of this study is to investigate the feasibility of matured soursop pulp flour (SPF) to be substituted with high-protein wheat flour in bread. Bread formulation was substituted with different levels of SPF (0%, 5%, 10% and 15%). The effect on physicochemical properties and sensory attributes were evaluated. Higher substitution level of SPF resulted in significantly higher (p
Abstract: The purpose of this research was to analyze and compare the instability of a contact surface between Copper and Nickel an alloy cathode in vacuum, the different ratio of Copper and Copper were conducted at 1%, 2% and 4% by using the cathode spot model. The transient recovery voltage is predicted. The cathode spot region is recognized as the collisionless space charge sheath connected with singly ionized collisional plasma. It was found that the transient voltage is decreased with increasing the percentage of an amount of Nickel in cathode materials.
Abstract: Dried tomato peel (DTP) was tested in vivo (n=10) in 42 week-old laying hens at rates of 0, 40, 70, 100 and 130g/kg DM feed. Laying hens were fed in group 120 g DM/day/animal for 26 days. After 21 days, feed intake was not affected after DTP incorporation (97% of the offered feed in the five groups). Laying rate was not significantly different after DTP incorporation at 4 and 10% from the control group. Egg yolk resulting from DTP-enriched diets, contained lower amounts of cholesterol (14 to 17mg/g) and triglyceride (188mg/g) compared to the control group (22 and 241 mg/g, respectively) (P
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: Optical Coherence Tomography (OCT) combined
with the Confocal Microscopy, as a noninvasive method, permits the
determinations of materials defects in the ceramic layers depth. For
this study 256 anterior and posterior metal and integral ceramic fixed
partial dentures were used, made with Empress (Ivoclar), Wollceram
and CAD/CAM (Wieland) technology. For each investigate area 350
slices were obtain and a 3D reconstruction was perform from each
stuck. The Optical Coherent Tomography, as a noninvasive method,
can be used as a control technique in integral ceramic technology,
before placing those fixed partial dentures in the oral cavity. The
purpose of this study is to evaluate the capability of En face Optical
Coherence Tomography (OCT) combined with a fluorescent method
in detection and analysis of possible material defects in metalceramic
and integral ceramic fixed partial dentures. As a conclusion,
it is important to have a non invasive method to investigate fixed
partial prostheses before their insertion in the oral cavity in order to
satisfy the high stress requirements and the esthetic function.
Abstract: Brain Computer Interface (BCI) has been recently
increased in research. Functional Near Infrared Spectroscope (fNIRs)
is one the latest technologies which utilize light in the near-infrared
range to determine brain activities. Because near infrared technology
allows design of safe, portable, wearable, non-invasive and wireless
qualities monitoring systems, fNIRs monitoring of brain
hemodynamics can be value in helping to understand brain tasks. In
this paper, we present results of fNIRs signal analysis indicating that
there exist distinct patterns of hemodynamic responses which
recognize brain tasks toward developing a BCI. We applied two
different mathematics tools separately, Wavelets analysis for
preprocessing as signal filters and feature extractions and Neural
networks for cognition brain tasks as a classification module. We
also discuss and compare with other methods while our proposals
perform better with an average accuracy of 99.9% for classification.
Abstract: For the past one decade, biclustering has become popular data mining technique not only in the field of biological data analysis but also in other applications like text mining, market data analysis with high-dimensional two-way datasets. Biclustering clusters both rows and columns of a dataset simultaneously, as opposed to traditional clustering which clusters either rows or columns of a dataset. It retrieves subgroups of objects that are similar in one subgroup of variables and different in the remaining variables. Firefly Algorithm (FA) is a recently-proposed metaheuristic inspired by the collective behavior of fireflies. This paper provides a preliminary assessment of discrete version of FA (DFA) while coping with the task of mining coherent and large volume bicluster from web usage dataset. The experiments were conducted on two web usage datasets from public dataset repository whereby the performance of FA was compared with that exhibited by other population-based metaheuristic called binary Particle Swarm Optimization (PSO). The results achieved demonstrate the usefulness of DFA while tackling the biclustering problem.