Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: The following paper shows an interactive tool which
main purpose is to teach how to play a flute. It consists of three
stages the first one is the instruction and teaching process through a
software application, the second is the practice part when the user
starts to play the flute (hardware specially designed for this
application) this flute is capable of capturing how is being played the
flute and the final stage is the one in which the data captured are sent
to the software and the user is evaluated in order to give him / she a
correction or an acceptance
Abstract: In this paper, we have applied the homotopy perturbation
method (HPM) for obtaining the analytical solution of unsteady
flow of gas through a porous medium and we have also compared the
findings of this research with some other analytical results. Results
showed a very good agreement between results of HPM and the
numerical solutions of the problem rather than other analytical solutions
which have previously been applied. The results of homotopy
perturbation method are of high accuracy and the method is very
effective and succinct.
Abstract: This paper investigates the effect of replacing
crankshaft with cam on the indicated torque during compression and
power strokes in internal combustion engines. A Cycloidal cam
profile was used in Revetec engine to calculate and compare the
torque to a conventional engine, using a computational method.
Firstly, the cylinder pressure was calculated using Ferguson equation,
and then the torque calculated depending on cylinder pressure values
in every crank angle. the results showed that by using Cycloidal cam
profile in Revetec engine the torque can increased by 14% compared
with conventional engines, which means an increase in engine
efficiency.
Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: Accurate and comprehensive thermodynamic properties of pure and mixture of refrigerants are in demand by both producers and users of these materials. Information about thermodynamic properties is important initially to qualify potential candidates for working fluids in refrigeration machinery. From practical point of view, Refrigerants and refrigerant mixtures are widely used as working fluids in many industrial applications, such as refrigerators, heat pumps, and power plants The present work is devoted to evaluating seven cubic equations of state (EOS) in predicting gas and liquid phase volumetric properties of nine ozone-safe refrigerants both in super and sub-critical regions. The evaluations, in sub-critical region, show that TWU and PR EOS are capable of predicting PVT properties of refrigerants R32 within 2%, R22, R134a, R152a and R143a within 1% and R123, R124, R125, TWU and PR EOS's, from literature data are 0.5% for R22, R32, R152a, R143a, and R125, 1% for R123, R134a, and R141b, and 2% for R124. Moreover, SRK EOS predicts PVT properties of R22, R125, and R123 to within aforementioned errors. The remaining EOS's predicts volumetric properties of this class of fluids with higher errors than those above mentioned which are at most 8%.In general, the results are in favor of the preference of TWU and PR EOS over other remaining EOS's in predicting densities of all mentioned refrigerants in both super and sub critical regions. Typically, this refrigerant is known to offer advantages such as ozone depleting potential equal to zero, Global warming potential equal to 140, and no toxic.
Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: The new semi-experimental method for simulation of
the turbine flow meters rotation in the transitional flow has been
developed. The method is based on the experimentally established
exponential low of changing of dimensionless relative turbine gas
meter rotation frequency and meter inertia time constant. For
experimental evaluation of the meter time constant special facility
has been developed. The facility ensures instant switching of turbine
meter under test from one channel to the other channel with different
flow rate and measuring the meter response. The developed method
can be used for evaluation and predication of the turbine meters
response and dynamic error in the transitional flow with any arbitrary
law of flow rate changing. The examples of the method application
are presented.
Abstract: Gas hydrates form when a number of factors co-exist:
free water, hydrocarbon gas, cold temperatures and high pressures are typical of the near mud-line conditions in a deepwater drilling
operation. Subsequently, when drilling with water based muds, particularly on exploration wells, the risk of hydrate formation
associated with a gas influx is high. The consequences of gas hydrate
formation while drilling are severe, and as such, every effort should be made to ensure the risk of hydrate formation is either eliminated
or significantly reduced. Thermodynamic inhibitors are used to reduce the free water content of a drilling mud, and thus suppress the
hydrate formation temperature. Very little experimental work has
been performed by oil and gas research companies on the evaluation
of gas hydrate formation in a water-based drilling mud. The main
objective of this paper is to investigate the experimental gas hydrate
formation for a mixture of methane, carbon dioxide & nitrogen in a
water-based drilling mud with or without presence of different
concentrations of thermodynamic inhibitors including pure salt and a
combination of salt with methanol or ethylene glycol at different
concentrations in a static loop apparatus. The experiments were
performed using a static loop apparatus consisting of a 2.4307 cm
inside diameter and 800 cm long pipe. All experiments were conducted at 2200 psia. The temperature in the loop was decreased at
a rate of 3.33 °F/h from initial temperature of 80 °F.
Abstract: The design of a gravity dam is performed through an
interactive process involving a preliminary layout of the structure
followed by a stability and stress analysis. This study presents a
method to define the optimal top width of gravity dam with genetic
algorithm. To solve the optimization task (minimize the cost of the
dam), an optimization routine based on genetic algorithms (GAs) was
implemented into an Excel spreadsheet. It was found to perform well
and GA parameters were optimized in a parametric study. Using the
parameters found in the parametric study, the top width of gravity
dam optimization was performed and compared to a gradient-based
optimization method (classic method). The accuracy of the results
was within close proximity. In optimum dam cross section, the ratio
of is dam base to dam height is almost equal to 0.85, and ratio of dam
top width to dam height is almost equal to 0.13. The computerized
methodology may provide the help for computation of the optimal
top width for a wide range of height of a gravity dam.
Abstract: Because of importance of energy, optimization of
power generation systems is necessary. Gas turbine cycles are
suitable manner for fast power generation, but their efficiency is
partly low. In order to achieving higher efficiencies, some
propositions are preferred such as recovery of heat from exhaust
gases in a regenerator, utilization of intercooler in a multistage
compressor, steam injection to combustion chamber and etc.
However thermodynamic optimization of gas turbine cycle, even
with above components, is necessary. In this article multi-objective
genetic algorithms are employed for Pareto approach optimization of
Regenerative-Intercooling-Gas Turbine (RIGT) cycle. In the multiobjective
optimization a number of conflicting objective functions
are to be optimized simultaneously. The important objective
functions that have been considered for optimization are entropy
generation of RIGT cycle (Ns) derives using Exergy Analysis and
Gouy-Stodola theorem, thermal efficiency and the net output power
of RIGT Cycle. These objectives are usually conflicting with each
other. The design variables consist of thermodynamic parameters
such as compressor pressure ratio (Rp), excess air in combustion
(EA), turbine inlet temperature (TIT) and inlet air temperature (T0).
At the first stage single objective optimization has been investigated
and the method of Non-dominated Sorting Genetic Algorithm
(NSGA-II) has been used for multi-objective optimization.
Optimization procedures are performed for two and three objective
functions and the results are compared for RIGT Cycle. In order to
investigate the optimal thermodynamic behavior of two objectives,
different set, each including two objectives of output parameters, are
considered individually. For each set Pareto front are depicted. The
sets of selected decision variables based on this Pareto front, will
cause the best possible combination of corresponding objective
functions. There is no superiority for the points on the Pareto front
figure, but they are superior to any other point. In the case of three
objective optimization the results are given in tables.
Abstract: In this paper is shown that the probability-statistic methods application, especially at the early stage of the aviation gas turbine engine (GTE) technical condition diagnosing, when the flight information has property of the fuzzy, limitation and uncertainty is unfounded. Hence is considered the efficiency of application of new technology Soft Computing at these diagnosing stages with the using of the Fuzzy Logic and Neural Networks methods. Training with high accuracy of fuzzy multiple linear and non-linear models (fuzzy regression equations) which received on the statistical fuzzy data basis is made. Thus for GTE technical condition more adequate model making are analysed dynamics of skewness and kurtosis coefficients' changes. Researches of skewness and kurtosis coefficients values- changes show that, distributions of GTE work parameters have fuzzy character. Hence consideration of fuzzy skewness and kurtosis coefficients is expedient. Investigation of the basic characteristics changes- dynamics of GTE work parameters allows to draw conclusion on necessity of the Fuzzy Statistical Analysis at preliminary identification of the engines' technical condition. Researches of correlation coefficients values- changes shows also on their fuzzy character. Therefore for models choice the application of the Fuzzy Correlation Analysis results is offered. For checking of models adequacy is considered the Fuzzy Multiple Correlation Coefficient of Fuzzy Multiple Regression. At the information sufficiency is offered to use recurrent algorithm of aviation GTE technical condition identification (Hard Computing technology is used) on measurements of input and output parameters of the multiple linear and non-linear generalised models at presence of noise measured (the new recursive Least Squares Method (LSM)). The developed GTE condition monitoring system provides stage-bystage estimation of engine technical conditions. As application of the given technique the estimation of the new operating aviation engine temperature condition was made.
Abstract: BioEnergy is an archetypal appropriate technology
and alternate source of energy in rural areas of China, and can meet
the basic need for cooking fuel in rural areas. The paper introduces
with an alternate mean of research that can accelerate the biogas
energy production. Tithonia diversifolia or the Tree marigold can be
hailed as mesophillic anaerobic digestion to increase the production
of more Bioenergy. Tithonia diversifolia is very native to Mexico and
Central America, which can be served as ornamental plants- green
manure and can prevent soil erosion. Tithonia diversifolia is widely
grown and known to Asia, Africa, America and Australia as well.
Nowadays, Considering China’s geographical condition it is found
that Tithonia diversifolia is widely growing plant in the many tropical
and subtropical regions of southern Yunnan- which can have great
usage in accelerating and increasing the Bioenergy production
technology. The paper discussed aiming at proving possibility that
Tithonia diversifolia can be applied in biogas fermentation and its
biogas production potential, the research carried experiment on
Tithonia diversifolia biogas fermentation under the mesophilic
condition (35 Celsius Degree). The result revealed that Tithonia
diversifolia can be used as biogas fermentative material, and 6%
concentration can get the best biogas production, with the TS biogas
production rate 656mL/g and VS biogas production rate 801mL/g. It
is well addressed that Tithonia diversifolia grows wildly in 53
Counties and 9 cities of Yunnan Province, which mainly grows in
form of the road side plants, the edge of the field, countryside, forest
edge, open space; of which demersum-natures can form dense
monospecific beds -causing serious harm to agricultural production
landforms threatening the ecological system as a potentially harmful
exotic plant. There are also found the three types of invasive daisy
alien plants -Eupatorium adenophorum, Eupatorium Odorata and
Tithonia diversifolia in Yunnan Province of China-among them the
Tithonia diversifolia is responsible for causing serious harm to
agricultural production. In this paper we have designed the
experimental explanation of Biogas energy production that requires
anaerobic environment and some microbes; Tithonia diversifolia
plant has been taken into consideration while carrying experiments
and with successful resulting of generating more BioEnergy
emphasizing on the practical applications of Tithonia diversifolia.
This paper aims at- to find a new mechanism to provide a more
scientific basis for the development of this plant herbicides in Biogas
energy and to improve the utilization throughout the world as well.
Abstract: Studies on the distribution of traffic demands have
been proceeding by providing traffic information for reducing
greenhouse gases and reinforcing the road's competitiveness in the
transport section, however, since it is preferentially required the
extensive studies on the driver's behavior changing routes and its
influence factors, this study has been developed a discriminant model
for changing routes considering driving conditions including traffic
conditions of roads and driver's preferences for information media. It
is divided into three groups depending on driving conditions in group
classification with the CART analysis, which is statistically
meaningful. And the extent that driving conditions and preferred
media affect a route change is examined through a discriminant
analysis, and it is developed a discriminant model equation to predict a
route change. As a result of building the discriminant model equation,
it is shown that driving conditions affect a route change much more,
the entire discriminant hit ratio is derived as 64.2%, and this
discriminant equation shows high discriminant ability more than a
certain degree.
Abstract: The increased use of biodiesel implies variations on both greenhouse gases and air pollutant emissions. Some studies point out that the use of biodiesel blends on diesel can help in controlling air pollution and promote a reduction of CO2 emissions. Reductions on PM, SO2, VOC and CO emissions are also expected, however NOx emissions may increase, which may potentiate O3 formation. This work aims to assess the impact of the biodiesel use on air quality, through a numerical modeling study, taking the Northern region of Portugal as a case study. The emission scenarios are focused on 2008 (baseline year) and 2020 (target year of Renewable Energy Directive-RED) and on three biodiesel blends (B0, B10 and B20). In a general way the use of biodiesel by 2020 will reduce the CO2 and air pollutants emissions in the Northern Portugal, improving air quality. However it will be in a very small extension.
Abstract: Sarkhoon gas plant, located in south of Iran, has been installed to removal H2S contained in a high pressure natural gas stream. The solvent used for the H2S removal from gaseous stream is 34% by weight (wt%) Di-ethanol amine (DEA) solutions. Due to increasing concentration of heat stable salt (HSS) in solvent, corrosivity of amine solution had been increased. Reports indicated that there was corrosion on the shell of regeneration column. Because source formation of HSS was unknown, we decided to control the amount of HSS at the limit less than 3% wt amine solvent. Therefore, two small columns were filled by strong anionic base and carbon active, and then polluted amine was passed through beds. Finally a temporary amine recovery package on industrial scale was made based on laboratory’s results. From economical point of view we could save $700000 beside corrosion occurrence of the stripping column has been vigorously decreased.
Abstract: Smoke from domestic wood burning has been
identified as a major contributor to air pollution, motivating detailed
emission measurements under controlled conditions. A series of
experiments was performed to characterise the emissions from wood
combustion in a fireplace and in a woodstove of two common species
of trees grown in Spain: Pyrenean oak (Quercus pyrenaica) and
black poplar (Populus nigra). Volatile organic compounds (VOCs) in
the exhaust emissions were collected in Tedlar bags, re-sampled in
sorbent tubes and analysed by thermal desorption-gas
chromatography-flame ionisation detection. Pyrenean oak presented
substantially higher emissions in the woodstove than in the fireplace,
for the majority of compounds. The opposite was observed for
poplar. Among the 45 identified species, benzene and benzenerelated
compounds represent the most abundant group, followed by
oxygenated VOCs and aliphatics. Emission factors obtained in this
study are generally of the same order than those reported for
residential experiments in the USA.
Abstract: In this study, multiwall carbon nanotubes (MWNTs)
were modified with nitric acid chemically and by dielectric barrier
discharge (DBD) plasma in an oxygen-based atmosphere. Used
carbon nanotubes (CNTs) were prepared by chemical vapour
deposition (CVD) floating catalyst method. For removing amorphous
carbon and metal catalyst, MWNTs were exposed to dry air and
washed with hydrochloric acid. Heating purified CNTs under helium
atmosphere caused elimination of acidic functional groups. Fourier
transformed infrared spectroscopy (FTIR) shows formation of
oxygen containing groups such as C=O and COOH. Brunauer,
Emmett, Teller (BET) analysis revealed that functionalization causes
generation of defects on the sidewalls and opening of the ends of
CNTs. Results of temperature-programmed desorption (TPD) and gas
chromatography(GC) indicate that nitric acid treatment create more
acidic groups than plasma treatment.
Abstract: Power transformer consists of components which are
under consistent thermal and electrical stresses. The major
component which degrades under these stresses is the paper
insulation of the power transformer. At site, lightning impulses and
cable faults may cause the winding deformation. In addition, the
winding may deform due to impact during transportation. A
deformed winding will excite more stress to its insulating paper thus
will degrade it. Insulation degradation will shorten the life-span of
the transformer. Currently there are two methods of detecting the
winding deformation which are Sweep Frequency Response
Analysis (SFRA) and Low Voltage Impulse Test (LVI). The latter
injects current pulses to the winding and capture the admittance
plot. In this paper, a transformer which experienced overheating and
arcing was identified, and both SFRA and LVI were performed.
Next, the transformer was brought to the factory for untanking. The
untanking results revealed that the LVI is more accurate than the
SFRA method for this case study.