Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Molluca Collision Zone is located at the junction of
the Eurasian, Australian, Pacific and the Philippines plates. Between
the Sangihe arc, west of the collision zone, and to the east of
Halmahera arc is active collision and convex toward the Molluca Sea.
This research will analyze the behavior of earthquake occurrence in
Molluca Collision Zone related to the distributions of an earthquake
in each partition regions, determining the type of distribution of a
occurrence earthquake of partition regions, and the mean occurence
of earthquakes each partition regions, and the correlation between the
partitions region. We calculate number of earthquakes using partition
method and its behavioral using conventional statistical methods. In
this research, we used data of shallow earthquakes type and its
magnitudes ≥4 SR (period 1964-2013). From the results, we can
classify partitioned regions based on the correlation into two classes:
strong and very strong. This classification can be used for early
warning system in disaster management.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: Apps are today the most important possibility to adapt
mobile phones and computers to fulfill the special needs of their
users. Location- and context-sensitive programs are hereby the key to
support the interaction of the user with his/her environment and also
to avoid an overload with a plenty of dispensable information. The
contribution shows, how a trusted, secure and really bi-directional
communication and interaction among users and their environment
can be established and used, e.g. in the field of home automation.
Abstract: The study identified the socio-economic and
demographic factors of both married and unmarried females in third
world countries. Almost all the countries have same problems but we
have selected Pakistan as a sample country. The main purpose of this
study was to examine which factors forced women to participate in
labor market. So the best technique of data collection was survey of
both married and unmarried females between the ages of 20 to 49.
Two models (probit and logit) were used to analyze the factors which
effect on FLFP. The result showed that some factors e.g. age;
education and marital status have significant effect on FLFP. The
findings showed that educated women and those who belong to joint
families are more participate because of financial pressure.
Abstract: The reachable set bounding estimation for distributed
delay systems with disturbances is a new problem. In this paper,we
consider this problem subject to not only time varying delay and
polytopic uncertainties but also distributed delay systems which is
not studied fully untill now. we can obtain improved non-ellipsoidal
reachable set estimation for neural networks with time-varying delay
by the maximal Lyapunov-Krasovskii fuctional which is constructed
as the pointwise maximum of a family of Lyapunov-Krasovskii
fuctionals corresponds to vertexes of uncertain polytope.On the other
hand,matrix inequalities containing only one scalar and Matlabs
LMI Toolbox is utilized to give a non-ellipsoidal description of the
reachable set.finally,numerical examples are given to illustrate the
existing results.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: The psychological impact of peer influence on its
individual group members, can make them resist HIV/AIDS
counselling and testing. This study investigated the correlate of peer
influence and resistance to HIV/AIDS counselling and testing among
students in tertiary institutions in Kano state, Nigeria. To achieve
this, three null hypotheses were postulated and tested. Cross-
Sectional Survey Design was employed in which 1512 sample was
selected from a student population of 104,841.Simple Random
Sampling was used in the selection. A self-developed 20-item scale
called Peer Influence and Psychological Resistance Inventory
(PIPRI) was used for data collection. Pearson Product Moment
Correlation (PPMCC) via test-retest method was applied to estimate a
reliability coefficient of 0.86 for the scale. Data obtained was
analyzed using t-test and PPMCC at 0.05 level of confidence. Results
reveal 26.3% (397) of the respondents being influenced by their peer
group, while 39.8% showed resistance. Also, the t-tests and PPMCC
statistics were greater than their respective critical values. This shows
that there was a significant gender difference in peer influence and a
difference between peer influence and resistance to HIV/AIDS
counselling and testing. However, a positive relationship between
peer influence and resistance to HIV/AIDS counselling and testing
was shown. A major recommendation offered suggests the use of
reinforcement and social support for positive attitudes and
maintenance of safe behaviour among students who patronize
HIV/AIDS counselling.
Abstract: This paper presents reliability indices evaluation of the
rotor core magnetization of the induction motor operated as a self
excited induction generator by using probability distribution approach
and Monte Carlo simulation. Parallel capacitors with calculated
minimum capacitive value across the terminals of the induction motor
operated as a SEIG with unregulated shaft speed have been connected
during the experimental study. A three phase, 4 poles, 50Hz, 5.5 hp,
12.3A, 230V induction motor coupled with DC Shunt Motor was
tested in the electrical machine laboratory with variable reactive loads.
Based on this experimental study, it is possible to choose a reliable
induction machines operated as a SEIG for unregulated renewable
energy application in remote area or where grid is not available.
Failure density function, cumulative failure distribution function,
survivor function, hazard model, probability of success and
probability of failure for reliability evaluation of the three phase
induction motor operating as a SEIG have been presented graphically
in this paper.
Abstract: In this paper, the effect of admixtures on the tensional
strength of concrete in Urmia-lake water have been investigated. We
made different types of concretes with the ratio of w/c and replaced
different percentages of micro-silica, air-entraining, super plasticizer,
corrosion-inhibiting, and caulk with two types of cement I and II as
well as investigating in both ordinary water and Urmia-lake water.
The tensional strength was investigated on these samples.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Nations are still finding it quite difficult to win mega
sport competitions despite the major contribution of sport to society
in terms of social and economic development, personal health, and in
education. Even though the world of sports has been transformed into
a huge global economy, it is important to note that the first step of
sport is usually its introduction to children at school through physical
education or PE. In other words, nations who do not win mega sport
competitions also suffer from a weak and neglected PE system. This
problem of the neglect of PE systems is the main motivation of this
research aimed at examining the factors affecting the perceived
awareness of physical education teachers on the ICTs that are
adoptable for the teaching and learning of physical education. Two
types of research objectives will materialize this aim: relevant
theories will be identified in relation to the analysis of the perceived
ICT awareness of PE teachers and subsequent models will be
compiled and designed from existing literature; the empirical testing
of such theories and models will also be achieved through the survey
of PE teachers from the Camperdown magisterial district of the
KwaZulu-Natal province of South Africa. The main hypothesis at the
heart of this study is the relationship between the demographics of PE
teachers, their behavior both as individuals and as social entities, and
their perceived awareness of the ICTs that are adoptable for PE, as
postulated by existing literature; except that this study categorizes
human behavior under performance expectancy, computer attitude,
and social influence. This hypothesis was partially confirmed by the
survey conducted by this research in the sense that performance
expectancy and teachers’ age, gender, computer usage, and class size
were found to be the only factors affecting their awareness of ICTs
for physical education.
Abstract: The world wide web network is a network with a
complex topology, the main properties of which are the distribution
of degrees in power law, A low clustering coefficient and a weak
average distance. Modeling the web as a graph allows locating the
information in little time and consequently offering a help in the
construction of the research engine. Here, we present a model based
on the already existing probabilistic graphs with all the aforesaid
characteristics. This work will consist in studying the web in order to
know its structuring thus it will enable us to modelize it more easily
and propose a possible algorithm for its exploration.
Abstract: In order to study the effect of drought stress on grain
yield, yield components and associated traits of durum wheat
cultivars, an experiment was done as split plot arrangement using
randomized complete block design with three replications in Ilam
province, Iran in 2009-2010 cropping season. Different levels of
irrigation (Full irrigation, drought stress at stem elongation,
Flowering and grain formation stages) were considered as a main plot
and three durum wheat cultivars (Yavaros, Seimareh and Karkheh)
were assigned as a sub plot. The results showed that drought stress
was significant on grain yield, spike.m-2, grain. Spike-1, 1000-grain
weight, biological yield, harvest index and protein content. Drought
stress at all stages caused a loss in grain yield and its components.
Full irrigation had the highest grain yield and yield components.
Drought stress at stem elongation, flowering and grain formation
stages caused a reduction in spike.m-2, grain.spike-1 and 1000-grain
weight, respectively. Protein content was significantly affected by
drought stress. The highest protein content was obtained from
drought stress at grain formation stage. Cultivars had an influence on
grain yield and yield components. Yavaros and Seimareh cultivars
had the highest and lowest grain yield, respectively. Interaction effect
between drought stress and cultivar had a significant effect on grain
and yield components. Full irrigation and Yavaros cultivar had the
highest grain yield and drought stress at grain formation stage and
Seimareh cultivar had the lowest grain yield, respectively.
Abstract: The development of the agricultural sector in Ghana
has been reliant on the use of irrigation systems to ensure food
security. However, the manual operation of these systems has not
facilitated their maximum efficiency due to human limitations.
This paper seeks to address this problem by designing and
implementing an efficient, cost effective automated system which
monitors and controls the water flow of irrigation through
communication with an authorized operator via text messages. The
automatic control component of the system is timer based with an
Atmega32 microcontroller and a real time clock from the SM5100B
cellular module. For monitoring purposes, the system sends periodic
notification of the system on the performance of duty via SMS to the
authorized person(s). Moreover, the GSM based Irrigation
Monitoring and Control System saves time and labour and reduces
cost of operating irrigation systems by saving electricity usage and
conserving water.
Field tests conducted have proven its operational efficiency and
ease of assessment of farm irrigation equipment due to its costeffectiveness
and data logging capabilities.
Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: In this paper a scheme is proposed for generating
a programmable current reference which can be implemented
in the CMOS technology. The current can be varied over a
wide range by changing an external voltage applied to one
of the control gates of FGMOS (Floating Gate MOSFET).
For a range of supply voltages and temperature, CMOS
current reference is found to be dependent, this dependence
is compensated by subtracting two current outputs with the
same dependencies on the supply voltage and temperature.
The system performance is found to improve with the
use of FGMOS. Mathematical analysis of the proposed
circuit is done to establish supply voltage and temperature
independence. Simulation and performance evaluation of the
proposed current reference circuit is done using TANNER
EDA Tools. The current reference shows the supply and
temperature dependencies of 520 ppm/V and 312 ppm/oC,
respectively. The proposed current reference can operate down
to 0.9 V supply.