Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: In this study, an experimental investigation was carried
out to fix CO2 into the electronic arc furnace (EAF) reducing slag from
stainless steelmaking process under wet grinding. The slag was ground
by the vibrating ball mill with the CO2 and pure water. The reaction
behavior was monitored with constant pressure method, and the
change of CO2 volume in the experimental system with grinding time
was measured. It was found that the CO2 absorption occurred as soon
as the grinding started. The CO2 absorption under wet grinding was
significantly larger than that under dry grinding. Generally, the
amount of CO2 absorption increased as the amount of water, the
amount of slag, the diameter of alumina ball and the initial pressure of
CO2 increased. However, the initial absorption rate was scarcely
influenced by the experimental conditions except for the initial CO2
pressure. According to this research, the CO2 reacted with the CaO
inside the slag to form CaCO3.
Abstract: This hypothesis shows that the induction and the
remanent of magnetic properties govern the mechanism processes of
DNA replication and the shortening of the telomere.
The solenoid–like formation of each parental DNA strand, which
exists at the initial stage of the replication process, enables an electric
charge transformation through the strand to produce a magnetic field.
The magnetic field, in turn, induces the surrounding medium to form
a new (replicated) strand by a remanent magnetisation. Through the
remanent [residual] magnetisation process, the replicated strand
possesses a similar information pattern to that of the parental strand.
In the same process, the remanent amount of magnetisation forms the
medium in which it has less of both repetitive and pattern
magnetisation than that of the parental strand, therefore the replicated
strand shows a shortening in the length of its telomeres.
Abstract: To compute dynamic characteristics of nonlinear viscoelastic springs with elastic structures having huge degree-of-freedom, Yamaguchi proposed a new fast numerical method using finite element method [1]-[2]. In this method, restoring forces of the springs are expressed using power series of their elongation. In the expression, nonlinear hysteresis damping is introduced. In this expression, nonlinear complex spring constants are introduced. Finite element for the nonlinear spring having complex coefficients is expressed and is connected to the elastic structures modeled by linear solid finite element. Further, to save computational time, the discrete equations in physical coordinate are transformed into the nonlinear ordinary coupled equations using normal coordinate corresponding to linear natural modes. In this report, the proposed method is applied to simulation for impact responses of a viscoelastic shock absorber with an elastic structure (an S-shaped structure) by colliding with a concentrated mass. The concentrated mass has initial velocities and collides with the shock absorber. Accelerations of the elastic structure and the concentrated mass are measured using Levitation Mass Method proposed by Fujii [3]. The calculated accelerations from the proposed FEM, corresponds to the experimental ones. Moreover, using this method, we also investigate dynamic errors of the S-shaped force transducer due to elastic mode in the S-shaped structure.
Abstract: The heterotrophic seedling growth can be defined as a
product of two components: (1) the weight of mobilized seed reserve,
and (2) conversion efficiency of utilized seed reserve to seedling
tissue. The first component can be further divided into (1) initial seed
weight, and (2) the fraction of seed reserve, which is mobilized. The
objective of this study was the identification of the sensitive seedling
growth component(s) in response to drought and salinity stresses.
Two experiments were separately conducted using various salinity
levels (osmotic pressure) of 0, 0.25, 0.50, 0.75, 1, 1.25 and 1.5 MPa
created using NaCl as first experiment and by polyethylene glycol
(drought stress) of 0, 0.2, 0.4, 0.6, 0.8, 1, 1.2 and 1.4 MPa in second
experiment. Seeds of five crops species (Hordeum vulgare, Brassica
napus, Zea mays, Medicago sativa and Medicago scutellata) were
used in each experiment. In both experiments, seedling growth,
fraction of seed reserve utilization and weight of mobilized seed
reserve decreased with increasing drought and salt intensity.
However, drought and salinity stresses had no effect on the
conversion efficiency. It was concluded that the sensitive component
of seedling growth is the weight of mobilized seed reserve.
Abstract: Composite of Celatom-ZeoliteY (Cel-ZY) was used to
remove cobalt ion from an aqueous solution using batch mode.
ZeoliteY has successfully superimposed on Celatom FW-14 surface
using hydrothermal treatment .The product was synthesized as a
novel of hierarchical porous material. It was observed from the
results that Cel-ZY has higher ability to remove cobalt ions than the
pure ZeoliteY powder (PZY) synthesized under the same conditions.
Several parameters were studied in this project to investigate the
effect of removal cobalt ion such as pH and initial cobalt
concentration. It was clearly observed that the uptake of cobalt ions
was affected with increase these parameters. The results proved that
the product can be used effectively to remove Co2+ ions from
wastewater as an environmentally friendly alternative.
Abstract: In this study, the sorption of Malachite green (MG) on Hydrilla verticillata biomass, a submerged aquatic plant, was investigated in a batch system. The effects of operating parameters such as temperature, adsorbent dosage, contact time, adsorbent size, and agitation speed on the sorption of Malachite green were analyzed using response surface methodology (RSM). The proposed quadratic model for central composite design (CCD) fitted very well to the experimental data that it could be used to navigate the design space according to ANOVA results. The optimum sorption conditions were determined as temperature - 43.5oC, adsorbent dosage - 0.26g, contact time - 200min, adsorbent size - 0.205mm (65mesh), and agitation speed - 230rpm. The Langmuir and Freundlich isotherm models were applied to the equilibrium data. The maximum monolayer coverage capacity of Hydrilla verticillata biomass for MG was found to be 91.97 mg/g at an initial pH 8.0 indicating that the optimum sorption initial pH. The external and intra particle diffusion models were also applied to sorption data of Hydrilla verticillata biomass with MG, and it was found that both the external diffusion as well as intra particle diffusion contributes to the actual sorption process. The pseudo-second order kinetic model described the MG sorption process with a good fitting.
Abstract: The main goal of this work is to propose a way for
combined use of two nontraditional algorithms by solving topological
problems on telecommunications concentrator networks. The
algorithms suggested are the Simulated Annealing algorithm and the
Genetic Algorithm. The Algorithm of Simulated Annealing unifies
the well known local search algorithms. In addition - Simulated
Annealing allows acceptation of moves in the search space witch lead
to decisions with higher cost in order to attempt to overcome any
local minima obtained. The Genetic Algorithm is a heuristic approach
witch is being used in wide areas of optimization works. In the last
years this approach is also widely implemented in
Telecommunications Networks Planning. In order to solve less or
more complex planning problem it is important to find the most
appropriate parameters for initializing the function of the algorithm.
Abstract: Paper presents knowledge about types of test in area
of materials properties of selected methods of rapid prototyping
technologies. In today used rapid prototyping technologies for
production of models and final parts are used materials in initial state
as solid, liquid or powder material structure. In solid state are used
various forms such as pellets, wire or laminates. Basic range
materials include paper, nylon, wax, resins, metals and ceramics. In
Fused Deposition Modeling (FDM) rapid prototyping technology are
mainly used as basic materials ABS (Acrylonitrile Butadiene
Styrene), polyamide, polycarbonate, polyethylene and polypropylene.
For advanced FDM applications are used special materials as silicon
nitrate, PZT (Piezoceramic Material - Lead Zirconate Titanate),
aluminium oxide, hydroxypatite and stainless steel.
Abstract: Application of pesticides in the paddy fields has
deleterious effects on non-target organisms including cyanobacteria
which are photosynthesizing and nitrogen fixing micro-organisms
contributing significantly towards soil fertility and crop yield.
Pesticide contamination in the paddy fields has manifested into a
serious global environmental concern. To study the effect of one such
pesticide, three cyanobacterial strains; Anabaena fertilissima,
Aulosira fertilissima and Westiellopsis prolifica were selected for
their stress responses to an Organochlorine insecticide - 6, 7, 8, 9, 10,
10-hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 4, 3-
benzodioxathiepine-3-oxide, with reference to their photosynthesic
pigments-chlorophyll-a and carotenoids as well as accessory
pigments-phycobiliproteins (phycocyanin, allophycocyanin and
phycoerythrin), stress induced biochemical metabolites like
carbohydrates, proteins, amino acids, phenols and enzymes-nitrate
reductase, glutamine synthetase and succinate dehydrogenase. All
the three cyanobacterial strains were adversely affected by the
insecticide doses and inhibition was dose dependent. Reduction in
photosynthetic and accessory pigments, metabolites, nitrogen fixing
and respiratory enzymes of the test organisms were accompanied
with an initial increase in their total protein at lower Organochlorine
doses. On the other hand, increased amount of phenols in all the
insecticide treated concentrations was indicative of stressed activities
of the organisms.
Abstract: In this article two algorithms, one based on variation iteration method and the other on Adomian's decomposition method, are developed to find the numerical solution of an initial value problem involving the non linear integro differantial equation where R is a nonlinear operator that contains partial derivatives with respect to x. Special cases of the integro-differential equation are solved using the algorithms. The numerical solutions are compared with analytical solutions. The results show that these two methods are efficient and accurate with only two or three iterations
Abstract: Needs of an efficient information retrieval in recent
years in increased more then ever because of the frequent use of
digital information in our life. We see a lot of work in the area of
textual information but in multimedia information, we cannot find
much progress. In text based information, new technology of data
mining and data marts are now in working that were started from the
basic concept of database some where in 1960.
In image search and especially in image identification,
computerized system at very initial stages. Even in the area of image
search we cannot see much progress as in the case of text based
search techniques. One main reason for this is the wide spread roots
of image search where many area like artificial intelligence,
statistics, image processing, pattern recognition play their role. Even
human psychology and perception and cultural diversity also have
their share for the design of a good and efficient image recognition
and retrieval system.
A new object based search technique is presented in this paper
where object in the image are identified on the basis of their
geometrical shapes and other features like color and texture where
object-co-relation augments this search process.
To be more focused on objects identification, simple images are
selected for the work to reduce the role of segmentation in overall
process however same technique can also be applied for other
images.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: This study proposes novel hybrid social network analysis and collaborative filtering approach to enhance the performance of recommender systems. The proposed model selects subgroups of users in Internet community through social network analysis (SNA), and then performs clustering analysis using the information about subgroups. Finally, it makes recommendations using cluster-indexing CF based on the clustering results. This study tries to use the cores in subgroups as an initial seed for a conventional clustering algorithm. This model chooses five cores which have the highest value of degree centrality from SNA, and then performs clustering analysis by using the cores as initial centroids (cluster centers). Then, the model amplifies the impact of friends in social network in the process of cluster-indexing CF.
Abstract: This study aimed to develop and initially validate an instrument that measures social competency among tertiary level faculty members. A review of extant literature on social competence was done. The review of extant literature led to the writing of the items in the initial instrument which was evaluated by 11 Subject Matter Experts (SMEs). The SMEs were either educators or psychologists. The results of the evaluations done by the SMEs served as bases for the creation of the pre-try-out instrument used in the first trial-run. Insights from the first trial-run participants led to the development of the main try-out instrument used in the final test administration. One Hundred Forty-one participants from five private Higher Education Institutions (HEIs) in the National Capital Region (NCR) and five private HEIs in Central Luzon in the Philippines participated in the final test administration. The reliability of the instrument was evaluated using Cronbach-s Coefficient Alpha formula and had a Cronbach-s Alpha of 0.92. On the other hand, Factor Analysis was used to evaluate the validity of the instrument and six factors were identified. The development of the final instrument was based on the results of the evaluation of the instrument-s reliability and validity. For purposes of recognition, the instrument was named “Social Competency Inventory for Tertiary Level Faculty Members (SCI-TLFM)."
Abstract: The objective of the present research manuscript is to
perform parametric, nonparametric, and decision tree analysis to
evaluate two treatments that are being used for breast cancer patients.
Our study is based on utilizing real data which was initially used in
“Tamoxifen with or without breast irradiation in women of 50 years
of age or older with early breast cancer" [1], and the data is supplied
to us by N.A. Ibrahim “Decision tree for competing risks survival
probability in breast cancer study" [2]. We agree upon certain aspects
of our findings with the published results. However, in this
manuscript, we focus on relapse time of breast cancer patients instead
of survival time and parametric analysis instead of semi-parametric
decision tree analysis is applied to provide more precise
recommendations of effectiveness of the two treatments with respect
to reoccurrence of breast cancer.
Abstract: The present work describes a computational study of
aerodynamic characteristics of GLC305 airfoil clean and with 16.7
min ice shape (rime 212) and 22.5 min ice shape (glaze 944).The
performance of turbulence models SA, Kε, Kω Std, and Kω SST
model are observed against experimental flow fields at different
Mach numbers 0.12, 0.21, 0.28 in a range of Reynolds numbers
3x106, 6x106, and 10.5x106 on clean and iced aircraft airfoil
GLC305. Numerical predictions include lift, drag and pitching
moment coefficients at different Mach numbers and at different angle
of attacks were done. Accuracy of solutions with respect to the
effects of turbulence models, variation of Mach number, initial
conditions, grid resolution and grid spacing near the wall made the
study much sensitive. Navier Stokes equation based computational
technique is used. Results are very close to the experimental results.
It has seen that SA and SST models are more efficient than Kε and
Kω standard in under study problem.
Abstract: In this paper, we study the existence, the boundedness and the asymptotic behavior of the positive solutions of a fuzzy nonlinear difference equations xn+1 = A + k i=0 Bi xn-i , n= 0, 1, · · · . where (xn) is a sequence of positive fuzzy numbers, A,Bi and the initial values x-k, x-k+1, · · · , x0 are positive fuzzy numbers. k ∈ {0, 1, 2, · · ·}.
Abstract: In pressure vessels contain hydrogen, the role of
hydrogen will be important because of hydrogen cracking problem. It
is difficult to predict what is happened in metallurgical field spite of a
lot of studies have been searched. The main role in controlling the
mass diffusion as driving force is related to stress. In this study, finite
element analysis is implemented to estimate material-s behavior
associated with hydrogen embrittlement. For this purpose, one model
of a pressure vessel is introduced that it has definite boundary and
initial conditions. In fact, finite element is employed to solve the
sequentially coupled mass diffusion with stress near a crack front in a
pressure vessel. Modeling simulation intergrarnular fracture of AISI
4135 steel due to hydrogen is investigated. So, distribution of
hydrogen and stress are obtained and they indicate that their
maximum amounts occur near the crack front. This phenomenon is
happened exactly the region between elastic and plastic field.
Therefore, hydrogen is highly mobile and can diffuse through crystal
lattice so that this zone is potential to trap high volume of hydrogen.
Consequently, crack growth and fast fracture will be happened.
Abstract: Recently, we have presented an initial implementation
of a model agent-based e-commerce system, which utilized a simple
price negotiation mechanism–English Auction. In this note we
discuss how a Dutch Auction involving multiple units of a product
can be included in our system. We present UML diagrams of
agents involved in price negotiations and briefly discuss rule-based
mechanism exemplifying Dutch Auction.