Abstract: In present work, prediction the effect of nose radius, rz (mm) on the equivalent strain (PEEQ) and surface finish during the machining of titanium alloy (Ti-6Al-4V) through orthogonal cutting process. The results were performed at several of the nose radiuses, rz (mm) while the cutting speed, vc (m/min), feed rate, f (mm/tooth) and depth of cut, d (mm) were remained constant. The equivalent plastic strain (PEEQ) was estimated by using finite element modeling (FEM) and applied through ABAQUS/EXPLICIT software. The simulation results led to conclude that the equivalent plastic strain (PEEQ) was increased and surface roughness (Ra) decreased when increasing nose radius, rz (mm) during the machining of titanium alloy (Ti–6Al–4V) in dry cutting conditions.
Abstract: MultiProtocol Label Switching (MPLS) is an
emerging technology that aims to address many of the existing issues
associated with packet forwarding in today-s Internetworking
environment. It provides a method of forwarding packets at a high
rate of speed by combining the speed and performance of Layer 2
with the scalability and IP intelligence of Layer 3. In a traditional IP
(Internet Protocol) routing network, a router analyzes the destination
IP address contained in the packet header. The router independently
determines the next hop for the packet using the destination IP
address and the interior gateway protocol. This process is repeated at
each hop to deliver the packet to its final destination. In contrast, in
the MPLS forwarding paradigm routers on the edge of the network
(label edge routers) attach labels to packets based on the forwarding
Equivalence class (FEC). Packets are then forwarded through the
MPLS domain, based on their associated FECs , through swapping
the labels by routers in the core of the network called label switch
routers. The act of simply swapping the label instead of referencing
the IP header of the packet in the routing table at each hop provides
a more efficient manner of forwarding packets, which in turn allows
the opportunity for traffic to be forwarded at tremendous speeds and
to have granular control over the path taken by a packet. This paper
deals with the process of MPLS forwarding mechanism,
implementation of MPLS datapath , and test results showing the
performance comparison of MPLS and IP routing. The discussion
will focus primarily on MPLS IP packet networks – by far the
most common application of MPLS today.
Abstract: It is important to give input information without other device in AR system. One solution is using hand for augmented reality application. Many researchers have proposed different solutions for hand interface in augmented reality. Analyze Histogram and connecting factor is can be example for that. Various Direction searching is one of robust way to recognition hand but it takes too much calculating time. And background should be distinguished with skin color. This paper proposes a hand tracking method to control the 3D object in augmented reality using depth device and skin color. Also in this work discussed relationship between several markers, which is based on relationship between camera and marker. One marker used for displaying virtual object and three markers for detecting hand gesture and manipulating the virtual object.
Abstract: The aim of this paper is to investigate a process of modernization of the People-s Republic of China. The theme of scientific research is interesting, first, because the Chinese model of development is recognized as successful and most dynamically developing. They are obliged by these successes of the modernization spent in the country. Economy modernization as the basic motive power of progress of the country is a priority direction of development in the Republic of Kazakhstan. So the example of successful development modernization processes in China can be rather useful to use in working out of the Kazakhstan national reforms.
Abstract: This paper presents the application of a signal intensity independent registration criterion for non-rigid body registration of medical images. The criterion is defined as the weighted ratio image of two images. The ratio is computed on a voxel per voxel basis and weighting is performed by setting the ratios between signal and background voxels to a standard high value. The mean squared value of the weighted ratio is computed over the union of the signal areas of the two images and it is minimized using the Chebyshev polynomial approximation. The geometric transformation model adopted is a local cubic B-splines based model.
Abstract: In this paper a modified version NXM of traditional 5X5 playfair cipher is introduced which enable the user to encrypt message of any Natural language by taking appropriate size of the matrix depending upon the size of the natural language. 5X5 matrix has the capability of storing only 26 characters of English language and unable to store characters of any language having more than 26 characters. To overcome this limitation NXM matrix is introduced which solve this limitation. In this paper a special case of Urdu language is discussed. Where # is used for completing odd pair and * is used for repeating letters.
Abstract: Image coding based on clustering provides immediate
access to targeted features of interest in a high quality decoded
image. This approach is useful for intelligent devices, as well as for
multimedia content-based description standards. The result of image
clustering cannot be precise in some positions especially on pixels
with edge information which produce ambiguity among the clusters.
Even with a good enhancement operator based on PDE, the quality of
the decoded image will highly depend on the clustering process. In
this paper, we introduce an ambiguity cluster in image coding to
represent pixels with vagueness properties. The presence of such
cluster allows preserving some details inherent to edges as well for
uncertain pixels. It will also be very useful during the decoding phase
in which an anisotropic diffusion operator, such as Perona-Malik,
enhances the quality of the restored image. This work also offers a
comparative study to demonstrate the effectiveness of a fuzzy
clustering technique in detecting the ambiguity cluster without losing
lot of the essential image information. Several experiments have been
carried out to demonstrate the usefulness of ambiguity concept in
image compression. The coding results and the performance of the
proposed algorithms are discussed in terms of the peak signal-tonoise
ratio and the quantity of ambiguous pixels.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.
Abstract: This paper presents the results of enhancing images from a left and right stereo pair in order to increase the resolution of a 3D representation of a scene generated from that same pair. A new neural network structure known as a Self Delaying Dynamic Network (SDN) has been used to perform the enhancement. The advantage of SDNs over existing techniques such as bicubic interpolation is their ability to cope with motion and noise effects. SDNs are used to generate two high resolution images, one based on frames taken from the left view of the subject, and one based on the frames from the right. This new high resolution stereo pair is then processed by a disparity map generator. The disparity map generated is compared to two other disparity maps generated from the same scene. The first is a map generated from an original high resolution stereo pair and the second is a map generated using a stereo pair which has been enhanced using bicubic interpolation. The maps generated using the SDN enhanced pairs match more closely the target maps. The addition of extra noise into the input images is less problematic for the SDN system which is still able to out perform bicubic interpolation.
Abstract: The sand production problem has led researchers into making various attempts to understand the phenomenon. The generally accepted concept is that the occurrence of sanding is due to the in-situ stress conditions and the induced changes in stress that results in the failure of the reservoir sandstone during hydrocarbon production from wellbores. By using a hypothetical cased (perforated) well, an approach to the problem is presented here by using Finite Element numerical modelling techniques. In addition to the examination of the erosion problem, the influence of certain key parameters is studied in order to ascertain their effect on the failure and subsequent erosion process. The major variables investigated include: drawdown, perforation depth, and the erosion criterion. Also included is the determination of the optimal mud pressure for given operational and reservoir conditions. The improved understanding between parameters enables the choice of optimal values to minimize sanding during oil production.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.
Abstract: In this paper, we use a one-step iteration scheme to approximate common fixed points of two quasi-asymptotically nonexpansive mappings. We prove weak and strong convergence theorems in a uniformly convex Banach space. Our results generalize the corresponding results of Yao and Chen [15] to a wider class of mappings while extend those of Khan, Abbas and Khan [4] to an improved one-step iteration scheme without any condition and improve upon many others in the literature.
Abstract: Throughout this paper, a relatively new technique, the Tabu search variable selection model, is elaborated showing how it can be efficiently applied within the financial world whenever researchers come across the selection of a subset of variables from a whole set of descriptive variables under analysis. In the field of financial prediction, researchers often have to select a subset of variables from a larger set to solve different type of problems such as corporate bankruptcy prediction, personal bankruptcy prediction, mortgage, credit scoring and the Arbitrage Pricing Model (APM). Consequently, to demonstrate how the method operates and to illustrate its usefulness as well as its superiority compared to other commonly used methods, the Tabu search algorithm for variable selection is compared to two main alternative search procedures namely, the stepwise regression and the maximum R 2 improvement method. The Tabu search is then implemented in finance; where it attempts to predict corporate bankruptcy by selecting the most appropriate financial ratios and thus creating its own prediction score equation. In comparison to other methods, mostly the Altman Z-Score model, the Tabu search model produces a higher success rate in predicting correctly the failure of firms or the continuous running of existing entities.
Abstract: We here propose improved version of elastic graph matching (EGM) as a face detector, called the multi-scale EGM (MS-EGM). In this improvement, Gabor wavelet-based pyramid reduces computational complexity for the feature representation often used in the conventional EGM, but preserving a critical amount of information about an image. The MS-EGM gives us higher detection performance than Viola-Jones object detection algorithm of the AdaBoost Haar-like feature cascade. We also show rapid detection speeds of the MS-EGM, comparable to the Viola-Jones method. We find fruitful benefits in the MS-EGM, in terms of topological feature representation for a face.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: This paper proposes new hybrid approaches for face
recognition. Gabor wavelets representation of face images is an
effective approach for both facial action recognition and face
identification. Perform dimensionality reduction and linear
discriminate analysis on the down sampled Gabor wavelet faces can
increase the discriminate ability. Nearest feature space is extended to
various similarity measures. In our experiments, proposed Gabor
wavelet faces combined with extended neural net feature space
classifier shows very good performance, which can achieve 93 %
maximum correct recognition rate on ORL data set without any preprocessing
step.
Abstract: We propose a decoy-pulse protocol for frequency-coded implementation of B92 quantum key distribution protocol. A direct extension of decoy-pulse method to frequency-coding scheme results in security loss as an eavesdropper can distinguish between signal and decoy pulses by measuring the carrier photon number without affecting other statistics. We overcome this problem by optimizing the ratio of carrier photon number of decoy-to-signal pulse to be as close to unity as possible. In our method the switching between signal and decoy pulses is achieved by changing the amplitude of RF signal as opposed to modulating the intensity of optical signal thus reducing system cost. We find an improvement by a factor of 100 approximately in the key generation rate using decoy-state protocol. We also study the effect of source fluctuation on key rate. Our simulation results show a key generation rate of 1.5×10-4/pulse for link lengths up to 70km. Finally, we discuss the optimum value of average photon number of signal pulse for a given key rate while also optimizing the carrier ratio.
Abstract: The Chinese Postman Problem (CPP) is one of the
classical problems in graph theory and is applicable in a wide range
of fields. With the rapid development of hybrid systems and model
based testing, Chinese Postman Problem with Time Dependent Travel
Times (CPPTDT) becomes more realistic than the classical problems.
In the literature, we have proposed the first integer programming
formulation for the CPPTDT problem, namely, circuit formulation,
based on which some polyhedral results are investigated and a cutting
plane algorithm is also designed. However, there exists a main drawback:
the circuit formulation is only available for solving the special
instances with all circuits passing through the origin. Therefore, this
paper proposes a new integer programming formulation for solving
all the general instances of CPPTDT. Moreover, the size of the circuit
formulation is too large, which is reduced dramatically here. Thus, it
is possible to design more efficient algorithm for solving the CPPTDT
in the future research.
Abstract: Wireless Mesh Networking is a promising proposal
for broadband data transmission in a large area with low cost and
acceptable QoS. These features- trade offs in WMNs is a hot research
field nowadays. In this paper a mathematical optimization framework
has been developed to maximize throughput according to upper
bound delay constraints. IEEE 802.11 based infrastructure
backhauling mode of WMNs has been considered to formulate the
MINLP optimization problem. Proposed method gives the full
routing and scheduling procedure in WMN in order to obtain
mentioned goals.