Abstract: In this paper, we are concerned with the design and
its simulation studies of a modified extremum seeking control for
nonlinear systems. A standard extremum seeking control has a simple
structure, but it takes a long time to reach an optimal operating point.
We consider a modification of the standard extremum seeking control
which is aimed to reach the optimal operating point more speedily
than the standard one. In the modification, PD acceleration term
is added before an integrator making a principal control, so that it
enables the objects to be regulated to the optimal point smoothly. This
proposed method is applied to Monod and Williams-Otto models to
investigate its effectiveness. Numerical simulation results show that
this modified method can improve the time response to the optimal
operating point more speedily than the standard one.
Abstract: The fine structure of supercavitation in the wake of a
symmetrical cylinder is studied with high-speed video cameras. The
flow is observed in a cavitation tunnel at the speed of 8m/sec when the
sidewall and the wake are partially filled with the massive cavitation
bubbles. The present experiment observed that a two-dimensional
ripple wave with a wave length of 0.3mm is propagated in a
downstream direction, and then abruptly increases to a thicker
three-dimensional layer. IR-photography recorded that the wakes
originated from the horseshoe vortexes alongside the cylinder. The
wake was developed to inside the dead water zone, which absorbed the
bubbly wake propelled from the separated vortices at the center of the
cylinder. A remote sensing classification technique (maximum most
likelihood) determined that the surface porosity was 0.2, and the mean
speed in the mixed wake was 7m/sec. To confirm the existence of
two-dimensional wave motions in the interface, the experiments were
conducted at a very low frequency, and showed similar gravity waves
in both the upper and lower interfaces.
Abstract: A parallel block method based on Backward
Differentiation Formulas (BDF) is developed for the parallel solution
of stiff Ordinary Differential Equations (ODEs). Most common
methods for solving stiff systems of ODEs are based on implicit
formulae and solved using Newton iteration which requires repeated
solution of systems of linear equations with coefficient matrix, I -
hβJ . Here, J is the Jacobian matrix of the problem. In this paper,
the matrix operations is paralleled in order to reduce the cost of the
iterations. Numerical results are given to compare the speedup and
efficiency of parallel algorithm and that of sequential algorithm.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.
Abstract: The competitive learning is an adaptive process in
which the neurons in a neural network gradually become sensitive to
different input pattern clusters. The basic idea behind the Kohonen-s
Self-Organizing Feature Maps (SOFM) is competitive learning.
SOFM can generate mappings from high-dimensional signal spaces
to lower dimensional topological structures. The main features of this
kind of mappings are topology preserving, feature mappings and
probability distribution approximation of input patterns. To overcome
some limitations of SOFM, e.g., a fixed number of neural units and a
topology of fixed dimensionality, Growing Self-Organizing Neural
Network (GSONN) can be used. GSONN can change its topological
structure during learning. It grows by learning and shrinks by
forgetting. To speed up the training and convergence, a new variant
of GSONN, twin growing cell structures (TGCS) is presented here.
This paper first gives an introduction to competitive learning, SOFM
and its variants. Then, we discuss some GSONN with fixed
dimensionality, which include growing cell structures, its variants
and the author-s model: TGCS. It is ended with some testing results
comparison and conclusions.
Abstract: In this paper we improve the quasilinearization method by barycentric Lagrange interpolation because of its numerical stability and computation speed to achieve a stable semi analytical solution. Then we applied the improved method for solving the Fin problem which is a nonlinear equation that occurs in the heat transferring. In the quasilinearization approach the nonlinear differential equation is treated by approximating the nonlinear terms by a sequence of linear expressions. The modified QLM is iterative but not perturbative and gives stable semi analytical solutions to nonlinear problems without depending on the existence of a smallness parameter. Comparison with some numerical solutions shows that the present solution is applicable.
Abstract: For higher order multiplications, a huge number of
adders or compressors are to be used to perform the partial product
addition. We have reduced the number of adders by introducing
special kind of adders that are capable to add five/six/seven bits per
decade. These adders are called compressors. Binary counter
property has been merged with the compressor property to develop
high order compressors. Uses of these compressors permit the
reduction of the vertical critical paths. A 16×16 bit multiplier has
been developed using these compressors. These compressors make
the multipliers faster as compared to the conventional design that
have been used 4-2 compressors and 3-2 compressors.
Abstract: One way for optimum loading of overdimensioning
conveyers is speed (capacity) decrement, with attention for
production capabilities and demands. At conveyers which drives with
three phase slip-ring induction motor, technically reasonable solution
for conveyer (driving motors) speed regulation is using constant
torque subsynchronous cascade with static semiconductor converter
and transformer for energy reversion to the power network. In the
paper is described mathematical model for parameter calculation of
two-motors 6 kV subsynchronous cascade. It is also demonstrated
that applying of this cascade gave several good properties, foremost
in electrical energy saving, also in improving of other energy
indexes, and finally that results in cost reduction of complete
electrical motor drive.
Abstract: In today-s new technology era, cluster has become a
necessity for the modern computing and data applications since many
applications take more time (even days or months) for computation.
Although after parallelization, computation speeds up, still time
required for much application can be more. Thus, reliability of the
cluster becomes very important issue and implementation of fault
tolerant mechanism becomes essential. The difficulty in designing a
fault tolerant cluster system increases with the difficulties of various
failures. The most imperative obsession is that the algorithm, which
avoids a simple failure in a system, must tolerate the more severe
failures. In this paper, we implemented the theory of watchdog timer
in a parallel environment, to take care of failures. Implementation of
simple algorithm in our project helps us to take care of different
types of failures; consequently, we found that the reliability of this
cluster improves.
Abstract: The demand of the energy management systems (EMS) set forth by modern power systems requires fast energy management systems. Contingency analysis is among the functions in EMS which is time consuming. In order to handle this limitation, this paper introduces agent based technology in the contingency analysis. The main function of agents is to speed up the performance. Negotiations process in decision making is explained and the issue set forth is the minimization of the operating costs. The IEEE 14 bus system and its line outage have been used in the research and simulation results are presented.
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: We analyze hand dexterity in Parkinson-s disease patients (PD) and control subjects using a natural manual transport task (moving an object from one place to another). Eight PD patients and ten control subjects performed the task repeatedly at maximum speed both in OFF and ON medicated status. The movement parameters and the grip and load forces were recorded by a single optoelectronic camera and force transducers built in the especially designed object. Using the force and velocity signals, ten subsequent phases of the transport movement were defined and their durations were measured. The outline of 3D optical measurement is presented to obtain more precise movement trajectory.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: Timetabling problems are often hard and timeconsuming
to solve. Most of the methods of solving them concern
only one problem instance or class. This paper describes a universal
method for solving large, highly constrained timetabling problems
from different domains. The solution is based on evolutionary
algorithm-s framework and operates on two levels – first-level
evolutionary algorithm tries to find a solution basing on given set of
operating parameters, second-level algorithm is used to establish
those parameters. Tabu search is employed to speed up the solution
finding process on first level. The method has been used to solve
three different timetabling problems with promising results.
Abstract: Higher-order Statistics (HOS), also known as
cumulants, cross moments and their frequency domain counterparts,
known as poly spectra have emerged as a powerful signal processing
tool for the synthesis and analysis of signals and systems. Algorithms
used for the computation of cross moments are computationally
intensive and require high computational speed for real-time
applications. For efficiency and high speed, it is often advantageous
to realize computation intensive algorithms in hardware. A promising
solution that combines high flexibility together with the speed of a
traditional hardware is Field Programmable Gate Array (FPGA). In
this paper, we present FPGA-based parallel architecture for the
computation of third-order cross moments. The proposed design is
coded in Very High Speed Integrated Circuit (VHSIC) Hardware
Description Language (VHDL) and functionally verified by
implementing it on Xilinx Spartan-3 XC3S2000FG900-4 FPGA.
Implementation results are presented and it shows that the proposed
design can operate at a maximum frequency of 86.618 MHz.
Abstract: The permanent magnet synchronous motor (PMSM) is
very useful in many applications. Vector control of PMSM is popular
kind of its control. In this paper, at first an optimal vector control for
PMSM is designed and then results are compared with conventional
vector control. Then, it is assumed that the measurements are noisy
and linear quadratic Gaussian (LQG) methodology is used to filter
the noises. The results of noisy optimal vector control and filtered
optimal vector control are compared to each other. Nonlinearity of
PMSM and existence of inverter in its control circuit caused that the
system is nonlinear and time-variant. With deriving average model,
the system is changed to nonlinear time-invariant and then the
nonlinear system is converted to linear system by linearization of
model around average values. This model is used to optimize vector
control then two optimal vector controls are compared to each other.
Simulation results show that the performance and robustness to noise
of the control system has been highly improved.
Abstract: The influence of full-fat soy flour (FFSF) and
extrusion conditions on the mechanical characteristics of dry
spaghetti were evaluated. Process was performed with screw speed of
10-40rpm and water circulating temperature of 35-70°C. Data
analysis using mixture design showed that this enrichment resulted in
significant differences in mechanical strength.
Abstract: In this research, the diffusion of innovation regarding
smartphone usage is analysed through a consumer behaviour theory.
This research aims to determine whether a pattern surrounding the
diffusion of innovation exists. As a methodology, an empirical study
of the switch from a conventional cell phone to a smartphone was
performed. Specifically, a questionnaire survey was completed by
general consumers, and the situational and behavioural characteristics
of switching from a cell phone to a smartphone were analysed. In
conclusion, we found that the speed of the diffusion of innovation, the
consumer behaviour characteristics, and the utilities of the product
vary according to the stage of the product life cycle.
Abstract: This paper proposes an effective algorithm approach to hybrid control systems combining fuzzy logic and conventional control techniques of controlling the speed of induction motor assumed to operate in high-performance drives environment. The introducing of fuzzy logic in the control systems helps to achieve good dynamical response, disturbance rejection and low sensibility to parameter variations and external influences. Some fundamentals of the fuzzy logic control are preliminary illustrated. The developed control algorithm is robust, efficient and simple. It also assures precise trajectory tracking with the prescribed dynamics. Experimental results have shown excellent tracking performance of the proposed control system, and have convincingly demonstrated the validity and the usefulness of the hybrid fuzzy controller in high-performance drives with parameter and load uncertainties. Satisfactory performance was observed for most reference tracks.