Abstract: The results from experimental research of deformation
by upsetting and die forging of lead specimens wit controlled impact
are presented. Laboratory setup for conducting the investigations,
which uses cold rocket engine operated with compressed air, is
described. The results show that when using controlled impact is
achieving greater plastic deformation and consumes less impact
energy than at ordinary impact deformation process.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: Proteins or genes that have similar sequences are likely to perform the same function. One of the most widely used techniques for sequence comparison is sequence alignment. Sequence alignment allows mismatches and insertion/deletion, which represents biological mutations. Sequence alignment is usually performed only on two sequences. Multiple sequence alignment, is a natural extension of two-sequence alignment. In multiple sequence alignment, the emphasis is to find optimal alignment for a group of sequences. Several applicable techniques were observed in this research, from traditional method such as dynamic programming to the extend of widely used stochastic optimization method such as Genetic Algorithms (GAs) and Simulated Annealing. A framework with combination of Genetic Algorithm and Simulated Annealing is presented to solve Multiple Sequence Alignment problem. The Genetic Algorithm phase will try to find new region of solution while Simulated Annealing can be considered as an alignment improver for any near optimal solution produced by GAs.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: Place is a where dimension formed by people-s
relationship with physical settings, individual and group activities,
and meanings. 'Place Attachment', 'Place Identity'and 'Sense of
Place' are some concepts that could describe the quality of people-s
relationships with a place. The concept of Sense of place is used in
studying human-place bonding, attachment and place meaning. Sense
of Place usually is defined as an overarching impression
encompassing the general ways in which people feel about places,
senses it, and assign concepts and values to it. Sense of place is
highlighted in this article as one of the prevailing concepts among
place-based researches. Considering dimensions of sense of place has
always been beneficial for investigating public place attachment and
pro-environmental attitudes towards these places. The creation or
preservation of Sense of place is important in maintaining the quality
of the environment as well as the integrity of human life within it.
While many scholars argued that sense of place is a vague concept,
this paper will summarize and analyze the existing seminal literature.
Therefore, in this paper first the concept of Sense of place and its
characteristics will be examined afterward the scales of Sense of
place will be reviewed and the factors that contribute to form Sense
of place will be evaluated and finally Place Attachment as an
objective dimension for measuring the sense of place will be
described.
Abstract: Today the intangible assets are the capital of knowledge and are the most important and the most valuable resource for organizations. All employees have knowledge independently of the kind of jobs they do. Knowledge is thus an asset, which influences business operations. The objective of this article is to identify knowledge continuity as an objective of business continuity management. The article has been prepared based on the analysis of secondary sources and the evaluation of primary sources of data by means of a quantitative survey conducted in the Czech Republic. The conclusion of the article is that organizations that apply business continuity management do not focus on the preservation of the knowledge of key employees. Organizations ensure knowledge continuity only intuitively, on a random basis, non-systematically and discontinuously. The non-ensuring of knowledge continuity represents a threat of loss of key knowledge for organizations and can also negatively affect business continuity.
Abstract: In this paper we have suggested a new system for egovernment.
In this method a government can design a precise and
perfect system to control people and organizations by using five
major documents. These documents contain the important
information of each member of a society and help all organizations to
do their informatics tasks through them. This information would be
available by only a national code and a secure program would
support it. The suggested system can give a good awareness to the
society and help it be managed correctly.
Abstract: Globalization, supported by information and
communication technologies, changes the rules of competitiveness
and increases the significance of information, knowledge and
network cooperation. In line with this trend, the need for efficient
trust-building tools has emerged. The absence of trust building
mechanisms and strategies was identified within several studies.
Through trust development, participation on e-business network and
usage of network services will increase and provide to SMEs new
economic benefits. This work is focused on effective trust building
strategies development for electronic business network platforms.
Based on trust building mechanism identification, the questionnairebased
analysis of its significance and minimum level of requirements
was conducted. In the paper, we are confirming the trust dependency
on e-Skills which play crucial role in higher level of trust into the
more sophisticated and complex trust building ICT solutions.
Abstract: In this research the Preparation of Land use map of
scanner LISS III satellite data, belonging to the IRS in the Aghche
region in Isfahan province, is studied carefully. For this purpose, the
IRS satellite images of August 2008 and various land preparation
uses in region including rangelands, irrigation farming, dry farming,
gardens and urban areas were separated and identified. Therefore, the
GPS and Erdas Imaging software were used and three methods of
Maximum Likelihood, Mahalanobis Distance and Minimum Distance
were analyzed. In each of these methods, matrix error and Kappa
index were calculated and accuracy of each method, based on
percentages: 53.13, 56.64 and 48.44, were obtained respectively.
Considering the low accuracy of these methods in separation of land
preparation use, the visual interpretation of the map was used.
Finally, regional visits of 150 points were noted at random and no
error was observed. It shows that the map prepared by visual
interpretation is in high accuracy. Although the probable errors due
to visual interpretation and geometric correction might happen but
the desired accuracy of the map which is more than 85 percent is
reliable.
Abstract: ECG contains very important clinical information about the cardiac activities of the heart. Often the ECG signal needs to be captured for a long period of time in order to identify abnormalities in certain situations. Such signal apart of a large volume often is characterised by low quality due to the noise and other influences. In order to extract features in the ECG signal with time-varying characteristics at first need to be preprocessed with the best parameters. Also, it is useful to identify specific parts of the long lasting signal which have certain abnormalities and to direct the practitioner to those parts of the signal. In this work we present a method based on wavelet transform, standard deviation and variable threshold which achieves 100% accuracy in identifying the ECG signal peaks and heartbeat as well as identifying the standard deviation, providing a quick reference to abnormalities.
Abstract: Heat Index describes the combined effect of
temperature and humidity on human body. This combined effect is
causing a serious threat to the health of people because of the
changing climate. With climate change, climate variability and thus
the occurrence of heat waves is likely to increase. Evidence is
emerging from the analysis of long-term climate records of an
increase in the frequency and duration of extreme temperature events
in all over Bangladesh particularly during summer. Summer season
has prolonged while winters have become short in Bangladesh.
Summers have become hotter and thus affecting the lives of the
people engaged in outdoor activities during scorching sun hours. In
2003 around 62 people died due to heat wave across the country. In
this paper Bangladesh is divided in four regions and heat index has
been calculated from 1960 to 2010 in these regions of the country.
The aim of this paper is to identify the spots most vulnerable to heat
strokes and heat waves due to high heat index. The results show
upward trend of heat index in almost all the regions of Bangladesh.
The highest increase in heat index value has been observed in areas
of South-west region and North-west Region. The highest change in
average heat index has been found in Jessore by almost 5.50C.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free and clamped-clamped boundary conditions.
Abstract: This paper presents a vertical silicon nanowire n- MOSFET integrated with a CMOS-compatible fully-silicided (FUSI) NiSi2 gate. Devices with nanowire diameter of 50nm show good electrical performance (SS < 70mV/dec, DIBL < 30mV/V, Ion/Ioff > 107). Most significantly, threshold voltage tunability of about 0.2V is shown. Although threshold voltage remains low for the 50nm diameter device, it is expected to become more positive as nanowire diameter reduces.
Abstract: This paper focuses on operational risk measurement
techniques and on economic capital estimation methods. A data
sample of operational losses provided by an anonymous Central
European bank is analyzed using several approaches. Loss
Distribution Approach and scenario analysis method are considered.
Custom plausible loss events defined in a particular scenario are
merged with the original data sample and their impact on capital
estimates and on the financial institution is evaluated. Two main
questions are assessed – What is the most appropriate statistical
method to measure and model operational loss data distribution? and
What is the impact of hypothetical plausible events on the financial
institution? The g&h distribution was evaluated to be the most
suitable one for operational risk modeling. The method based on the
combination of historical loss events modeling and scenario analysis
provides reasonable capital estimates and allows for the measurement
of the impact of extreme events on banking operations.
Abstract: A new fast correlation algorithm for calibrating the
wavelength of Optical Spectrum Analyzers (OSAs) was introduced
in [1]. The minima of acetylene gas spectra were measured and
correlated with saved theoretical data [2]. So it is possible to find the
correct wavelength calibration data using a noisy reference spectrum.
First tests showed good algorithmic performance for gas line spectra
with high noise. In this article extensive performance tests were made
to validate the noise resistance of this algorithm. The filter and
correlation parameters of the algorithm were optimized for improved
noise performance. With these parameters the performance of this
wavelength calibration was simulated to predict the resulting
wavelength error in real OSA systems. Long term simulations were
made to evaluate the performance of the algorithm over the lifetime
of a real OSA.
Abstract: The aim of the present study was to develop and
validate an inexpensive and simple high performance liquid
chromatographic (HPLC) method for the determination of colistin
sulfate. Separation of colistin sulfate was achieved on a ZORBAX
Eclipse XDB-C18 column using UV detection at λ=215 nm. The
mobile phase was 30 mM sulfate buffer (pH 2.5):acetonitrile(76:24).
An excellent linearity (r2=0.998) was found in the concentration
range of 25 - 400 μg/mL. Intra- day and inter-day precisions of
method (%RSD, n=3) were less than 7.9%.The developed and
validated method was applied to determination of the content of
colistin sulfate in medicated premix and animal feed sample.The
recovery of colistin from animal feed was satisfactorily ranged from
90.92 to 93.77%. The results demonstrated that the HPLC method
developed in this work is appropriate for direct determination of
colistin sulfate in commercial medicated premixes and animal feed.
Abstract: Speckled images arise when coherent microwave,
optical, and acoustic imaging techniques are used to image an object, surface or scene. Examples of coherent imaging systems include synthetic aperture radar, laser imaging systems, imaging sonar
systems, and medical ultrasound systems. Speckle noise is a form of object or target induced noise that results when the surface of the object is Rayleigh rough compared to the wavelength of the illuminating radiation. Detection and estimation in images corrupted
by speckle noise is complicated by the nature of the noise and is not
as straightforward as detection and estimation in additive noise. In
this work, we derive stochastic models for speckle noise, with an emphasis on speckle as it arises in medical ultrasound images. The
motivation for this work is the problem of segmentation and tissue classification using ultrasound imaging. Modeling of speckle in this
context involves partially developed speckle model where an underlying Poisson point process modulates a Gram-Charlier series
of Laguerre weighted exponential functions, resulting in a doubly
stochastic filtered Poisson point process. The statistical distribution of partially developed speckle is derived in a closed canonical form.
It is observed that as the mean number of scatterers in a resolution cell is increased, the probability density function approaches an
exponential distribution. This is consistent with fully developed speckle noise as demonstrated by the Central Limit theorem.
Abstract: The purpose of this paper is to guide the effort in
improving the economic added value of Indonesian fisheries product
through post fishing program, which is cold storage program.
Indonesia's fisheries potential has been acknowledged by the world.
FAO (2009) stated that Indonesia is one of the tenth highest
producers of fishery products in the world. Based on BPS (Statistics
Indonesia data), the national fisheries production in 2011 reached
5.714 million tons, which 93.55% came from marine fisheries and
6.45% from open waters. Indonesian territory consist of 2/3 of
Indonesian waters, has given enormous benefits for Indonesia,
especially fishermen. To improve the economic level of fishermen
requires efforts to develop fisheries business unit. On of the efforts is
by improving the quality of products which are marketed in the
regional and international levels. It is certainly need the support of
the existence of various fishery facilities (infrastructure to
superstructure), one of which is cold storage. Given the many
benefits of cold storage as a means of processing of fishery resources,
Indonesia Maritime Security Coordinating Board (IMSCB) as one of
the maritime institutions for maritime security and safety, has a
program to empower the coastal community through encourages the
development of cold storage in the middle and lower fishery business
unit. The development of cold storage facilities which able to run its
maximum role requires synergistic efforts of various parties.
Abstract: Knowledge-based e-mail systems focus on
incorporating knowledge management approach in order to enhance
the traditional e-mail systems. In this paper, we present a knowledgebased
e-mail system called KS-Mail where people do not only send
and receive e-mail conventionally but are also able to create a sense
of knowledge flow. We introduce semantic processing on the e-mail
contents by automatically assigning categories and providing links to
semantically related e-mails. This is done to enrich the knowledge
value of each e-mail as well as to ease the organization of the e-mails
and their contents. At the application level, we have also built
components like the service manager, evaluation engine and search
engine to handle the e-mail processes efficiently by providing the
means to share and reuse knowledge. For this purpose, we present the
KS-Mail architecture, and elaborate on the details of the e-mail
server and the application server. We present the ontology mapping
technique used to achieve the e-mail content-s categorization as well
as the protocols that we have developed to handle the transactions in
the e-mail system. Finally, we discuss further on the implementation
of the modules presented in the KS-Mail architecture.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.