Abstract: Cloud Computing refers to applications delivered as
services over the internet, and the datacenters that provide those
services with hardware and systems software. These were earlier
referred to as Software as a Service (SaaS). Scheduling is justified by
job components (called tasks), lack of information. In fact, in a large
fraction of jobs from machine learning, bio-computing, and image
processing domains, it is possible to estimate the maximum time
required for a task in the job. This study focuses on Trust based
scheduling to improve cloud security by modifying Heterogeneous
Earliest Finish Time (HEFT) algorithm. It also proposes TR-HEFT
(Trust Reputation HEFT) which is then compared to Dynamic Load
Scheduling.
Abstract: In the present study we have investigated axial
buckling characteristics of nanocomposite beams reinforced by
single-walled carbon nanotubes (SWCNTs). Various types of beam
theories including Euler-Bernoulli beam theory, Timoshenko beam
theory and Reddy beam theory were used to analyze the buckling
behavior of carbon nanotube-reinforced composite beams.
Generalized differential quadrature (GDQ) method was utilized to
discretize the governing differential equations along with four
commonly used boundary conditions. The material properties of the
nanocomposite beams were obtained using molecular dynamic (MD)
simulation corresponding to both short-(10,10) SWCNT and long-
(10,10) SWCNT composites which were embedded by amorphous
polyethylene matrix. Then the results obtained directly from MD
simulations were matched with those calculated by the mixture rule
to extract appropriate values of carbon nanotube efficiency
parameters accounting for the scale-dependent material properties.
The selected numerical results were presented to indicate the
influences of nanotube volume fractions and end supports on the
critical axial buckling loads of nanocomposite beams relevant to
long- and short-nanotube composites.
Abstract: The knitted fabric suffers a deformation in its
dimensions due to stretching and tension factors, transverse and
longitudinal respectively, during the process in rectilinear knitting
machines so it performs a dry relaxation shrinkage procedure and
thermal action of prefixed to obtain stable conditions in the knitting.
This paper presents a dry relaxation shrinkage prediction of Bordeaux
fiber using a feed forward neural network and linear regression
models. Six operational alternatives of shrinkage were predicted. A
comparison of the results was performed finding neural network
models with higher levels of explanation of the variability and
prediction. The presence of different reposes is included. The models
were obtained through a neural toolbox of Matlab and Minitab
software with real data in a knitting company of Southern
Guanajuato. The results allow predicting dry relaxation shrinkage of
each alternative operation.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: The hydrodynamic and thermal behaviors of fluid
flow in wavy microchannel are investigated numerically. Effects of
Reynolds number on the hydrodynamics and thermal behaviors are
investigated. Three cases of Reynolds number (580, 1244, and 1910)
are adopted in this study. It is found that the separation zone begin
appears when Reynolds number is greater than 1910 at the endsection
of the wave. Also it is found that dimensionless maximum
velocity at the mid-section of the wave decreases and becomes as a
turbulent behavior as Reynolds numbers increases. The maximum
temperature at the center line at the mid-section of the wave increases
as Reynolds number increases until it reaches the turbulent behavior
when Reynolds number is equal or greater than 1244, while this
behavior will be achieved at very high velocities at the end section of
the wave.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: Lots of motors have been being used in industry.
Therefore many researchers have studied about the failure diagnosis of
motors. In this paper, the effect of measuring environment for
diagnosis of gear fault connected to a motor shaft is studied. The fault
diagnosis is executed through the comparison of normal gear and
abnormal gear. The measured FFT data are compared with the normal
data and analyzed for q-axis current, noise and vibration. For bad and
good environment, the diagnosis results are compared. From these, it
is shown that the bad measuring environment may not be able to detect
exactly the motor gear fault. Therefore it is emphasized that the
measuring environment should be carefully prepared.
Abstract: This paper addresses the issue of resource allocation
in the emerging cognitive technology. Focusing the Quality of
Service (QoS) of Primary Users (PU), a novel method is proposed for
the resource allocation of Secondary Users (SU). In this paper, we
propose the unique Utility Function in the game theoretic model of
Cognitive Radio which can be maximized to increase the capacity of
the Cognitive Radio Network (CRN) and to minimize the
interference scenario. Utility function is formulated to cater the need
of PUs by observing Signal to Noise ratio. Existence of Nash
Equilibrium for the postulated game is established.
Abstract: Thermal enhancement of a single mini channel in
Proton Exchange Membrane Fuel Cell (PEMFC) cooling plate is
numerically investigated. In this study, low concentration of Al2O3 in
Water - Ethylene Glycol mixtures is used as coolant in single channel
of carbon graphite plate to mimic the mini channels in PEMFC
cooling plate. A steady and incompressible flow with constant heat
flux is assumed in the channel of 1mm x 5mm x 100mm. Nano
particle of Al2O3 used ranges from 0.1, 0.3 and 0.5 vol %
concentration and then dispersed in 60:40 (water: Ethylene Glycol)
mixture. The effect of different flow rates to fluid flow and heat
transfer enhancement in Re number range of 20 to 140 was observed.
The result showed that heat transfer coefficient was improved by
18.11%, 9.86% and 5.37% for 0.5, 0.3 and 0.1 vol. % Al2O3 in 60:40
(water: EG) as compared to base fluid of 60:40 (water: EG). It is also
showed that the higher vol. % concentration of Al2O3 performed
better in term of thermal enhancement but at the expense of higher
pumping power required due to increase in pressure drop
experienced. Maximum additional pumping power of 0.0012W was
required for 0.5 vol % Al2O3 in 60:40 (water: EG) at Re number 140.
Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: In recent years, new techniques for solving complex
problems in engineering are proposed. One of these techniques is
JPSO algorithm. With innovative changes in the nature of the jump
algorithm JPSO, it is possible to construct a graph-based solution
with a new algorithm called G-JPSO. In this paper, a new algorithm
to solve the optimal control problem Fletcher-Powell and optimal
control of pumps in water distribution network was evaluated.
Optimal control of pumps comprise of optimum timetable operation
(status on and off) for each of the pumps at the desired time interval.
Maximum number of status on and off for each pumps imposed to the
objective function as another constraint. To determine the optimal
operation of pumps, a model-based optimization-simulation
algorithm was developed based on G-JPSO and JPSO algorithms.
The proposed algorithm results were compared well with the ant
colony algorithm, genetic and JPSO results. This shows the
robustness of proposed algorithm in finding near optimum solutions
with reasonable computational cost.
Abstract: Operation enhancement in an air cooler depends on
rate of heat transfer, and pressure drop. In this paper for a given heat
duty, study of the effects of FPI (Fin Per Inch) and fin type (circular
and hexagonal fins) on heat transfer, and pressure drop in an air
cooler in Iran, Arvand petrochemical. A program in EES
(Engineering Equations Solver) software moreover, Aspen B-JAC
and HTFS+ softwares are used for this purpose to solve governing
equations. At first the simulated results obtained from this program is
compared to the experimental data for two cases of FPI. The effects
of FPI from 3 to 15 over heat transfer (Q) to pressure drop ratio
(Q/Δp ratio). This ratio is one of the main parameters in design, and
simulation heat exchangers. The results show that heat transfer (Q)
and pressure drop increase with increasing FPI steadily, and the Q/Δp
ratio increases to FPI=12 and then decreased gradually to FPI=15,
and Q/Δp ratio is maximum at FPI=12. The FPI value selection
between 8 and 12 obtained as a result to optimum heat transfer to
pressure drop ratio. Also by contrast, between circular and hexagonal
fins results, the Q/Δp ratio of hexagonal fins more than Q/Δp ratio of
circular fins for FPI between 8 and 12 (optimum FPI)
Abstract: This paper reports the viability of developing Zn-27Al
alloy matrix hybrid composites reinforced with alumina, graphite and
fly ash (solid waste bye product of coal in thermal power plants).
This research work was aimed at developing low cost-high
performance Zn-27Al matrix composite with low density. Alumina
particulates (Al2O3), graphite added with 0, 2, 3, 4 and 5 wt% fly ash
were utilized to prepare 10wt% reinforcing phase with Zn-27Al alloy
as matrix using two-step stir casting method. Density measurement,
estimated percentage porosity, tensile testing, micro hardness
measurement and optical microscopy were used to assess the
performance of the composites produced. The results show that the
hardness, ultimate tensile strength, and percent elongation of the
hybrid composites decrease with increase in fly ash content. The
maximum decrease in hardness and ultimate tensile strength of
13.72% and 15.25% respectively were observed for composite grade
containing 5wt% fly ash. The percentage elongation of composite
sample without fly ash is 8.9% which is comparable with that of the
sample containing 2wt% fly ash with percentage elongation of 8.8%.
The fracture toughness of the fly ash containing composites was
however superior to those of composites without fly ash with 5wt%
fly ash containing composite exhibiting the highest fracture
toughness. The results show that fly ash can be utilized as
complementary reinforcement in ZA-27 alloy matrix composite to
reduce cost.
Abstract: Rapid population growth, urbanization and
industrialization are known as the most important factors of
environment problems. Elimination and management of solid wastes
are also within the most important environment problems. One of the
main problems in solid waste management is the selection of the best
site for elimination of solid wastes. Lately, Geographical Information
System (GIS) has been used for easing selection of landfill area. GIS
has the ability of imitating necessary economic, environmental and
political limitations. They play an important role for the site selection
of landfill area as a decision support tool. In this study; map layers will be studied for minimum effect of
environmental, social and cultural factors and maximum effect for
engineering/economic factors for site selection of landfill areas and
using GIS for a decision support mechanism in solid waste landfill
areas site selection will be presented in Aksaray/Turkey city,
Güzelyurt district practice.
Abstract: Environmental and functional conditions, sometimes,
necessitate the architectural plan of the building to be asymmetric,
and this result in an asymmetric structure. In such cases finding an
optimal pattern for locating the components of lateral load bearing
system, including shear walls, in the building’s plan is desired. In
case of shear wall in addition to the location the shape of the wall
cross-section is also an effective factor. Various types of shear walls
and their proper layout might come effective in better stiffness
distribution and more appropriate seismic response of the building.
Several studies have been conducted in the context of analysis and
design of shear walls; however, few studies have been performed on
making decisions for the location and form of shear walls in multistory
buildings, especially those with irregular plan. In this study, an
attempt has been made to obtain the most reliable seismic behavior of
multi-story reinforced concrete vertically chamfered buildings by
using more appropriate shear walls form and arrangement in 7-, 10-,
12-, and 15-stoy buildings. The considered forms and arrangements
include common rectangular walls and L-, T-, U- and Z-shaped plan,
located as the core or in the outer frames of the building structure.
Comparison of seismic behaviors of the buildings, including
maximum roof displacement and particularly formation of plastic
hinges and their distribution in the buildings’ structures, have been
done based on the results of a series of nonlinear time history
analyses, by using a set of selected earthquake records. Results show
that shear walls with U-shaped cross-section, placed as the building
central core, and also walls with Z-shaped cross-section, placed at the
corners give the building more reliable seismic behavior.
Abstract: Analyzing the relation networks between the hospital
buildings which have complex structure and distinctive spatial
relationships is quite difficult. The hospital buildings which require
specialty in spatial relationship solutions during design and selfinnovation
through the developing technology should survive and
keep giving service even after the disasters such as earthquakes. In
this study, a hospital building where the load-bearing system was
strengthened because of the insufficient earthquake performance and
the construction of an additional building was required to meet the
increasing need for space was discussed and a comparative spatial
evaluation of the hospital building was made with regard to its status
before the change and after the change. For this reason, spatial
organizations of the building before change and after the change were
analyzed by means of Space Syntax method and the effects of the
change on space organization parameters were searched by applying
an analytical procedure. Using Depthmap UCL software,
Connectivity, Visual Mean Depth, Beta and Visual Integration
analyses were conducted. Based on the data obtained after the
analyses, it was seen that the relationships between spaces of the
building increased after the change and the building has become more
explicit and understandable for the occupants. Furthermore, it was
determined according to findings of the analysis that the increase in
depth causes difficulty in perceiving the spaces and the changes
considering this problem generally ease spatial use.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: Structural analysis of flexible pavements has been and still is currently performed using multi-layer elastic theory. However, for thinly surfaced pavements subjected to low to medium volumes of traffics, the importance of non-linear stress-strain behavior of unbound granular materials (UGM) requires the use of more sophisticated numerical models for structural design and performance of such pavements. In the present work, nonlinear unbound aggregates constitutive model is implemented within an axisymmetric finite element code developed to simulate the nonlinear behavior of pavement structures including two local aggregates of different mineralogical nature, typically used in Algerian pavements. The performance of the mechanical model is examined about its capability of representing adequately, under various conditions, the granular material non-linearity in pavement analysis. In addition, deflection data collected by Falling Weight Deflectometer (FWD) are incorporated into the analysis in order to assess the sensitivity of critical pavement design criteria and pavement design life to the constitutive model. Finally, conclusions of engineering significance are formulated.
Abstract: This paper discusses micrometeorological aspects of the urban climate in three cities in Western São Paulo State: Presidente Prudente, Assis and Iepê. Particular attention is paid to the method used to estimate the components of the energy balance at the surface. Estimates of convective fluxes showed that the Bowen ratio was an indicator of the local climate and that its magnitude varied between 0.3 and 0.7. Maximum values for the Bowen ratio occurred earlier in Iepê (11:00 am) than in Presidente Prudente (4:00 pm). The results indicate that the Bowen ratio is modulated by the radiation balance at the surface and by different clusters of vegetation.