Abstract: to simulate the phenomenon of electronic transport in semiconductors, we try to adapt a numerical method, often and most frequently it’s that of Monte Carlo. In our work, we applied this method in the case of a ternary alloy semiconductor GaInP in its cubic form; The Calculations are made using a non-parabolic effective-mass energy band model. We consider a band of conduction to three valleys (ΓLX), major of the scattering mechanisms are taken into account in this modeling, as the interactions with the acoustic phonons (elastic collisions) and optics (inelastic collisions). The polar optical phonons cause anisotropic collisions, intra-valleys, very probable in the III-V semiconductors. Other optical phonons, no polar, allow transitions inter-valleys. Initially, we present the full results obtained by the simulation of Monte Carlo in GaInP in stationary regime. We consider thereafter the effects related to the application of an electric field varying according to time, we thus study the transient phenomenon which make their appearance in ternary material
Abstract: The aim of this paper is to confirm the effect of key
design parameters, the punch radius and punch angle, on rupture of the
expansion tube using a finite element analysis with a ductile damage
model. The results of the finite element analysis indicated that the
expansion ratio of the tube was mainly affected by the radius of the
punch. However, the rupture was more affected by the punch angle
than the radius of the punch. The existence of a specific punch angle,
at which rupture did not occur, even if the radius of the punch was
increased, was found.
Abstract: This paper presents a novel approach for the design of
microwave circuits using Adaptive Network Fuzzy Inference
Optimizer (ANFIO). The method takes advantage of direct synthesis
of subsections of the amplifier using very fast and accurate ANFIO
models based on exact simulations using ADS. A mapping from
course space to fine space known as space mapping is also used. The
proposed synthesis approach takes into account the noise and
scattering parameters due to parasitic elements to achieve optimal
results. The overall ANFIO system is capable of designing different
LNAs at different noise and scattering criteria. This approach offers
significantly reduced time in the design of microwave amplifiers
within the validity range of the ANFIO system. The method has been
proven to work efficiently for a 2.4GHz LNA example. The S21 of
10.1 dB and noise figure (NF) of 2.7 dB achieved for ANFIO while
S21 of 9.05 dB and NF of 2.6 dB achieved for ANN.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.
Abstract: Protein-protein interactions (PPI) play a crucial role in many biological processes such as cell signalling, transcription, translation, replication, signal transduction, and drug targeting, etc. Structural information about protein-protein interaction is essential for understanding the molecular mechanisms of these processes. Structures of protein-protein complexes are still difficult to obtain by biophysical methods such as NMR and X-ray crystallography, and therefore protein-protein docking computation is considered an important approach for understanding protein-protein interactions. However, reliable prediction of the protein-protein complexes is still under way. In the past decades, several grid-based docking algorithms based on the Katchalski-Katzir scoring scheme were developed, e.g., FTDock, ZDOCK, HADDOCK, RosettaDock, HEX, etc. However, the success rate of protein-protein docking prediction is still far from ideal. In this work, we first propose a more practical measure for evaluating the success of protein-protein docking predictions,the rate of first success (RFS), which is similar to the concept of mean first passage time (MFPT). Accordingly, we have assessed the ZDOCK bound and unbound benchmarks 2.0 and 3.0. We also createda new benchmark set for protein-protein docking predictions, in which the complexes have experimentally determined binding affinity data. We performed free energy calculation based on the solution of non-linear Poisson-Boltzmann equation (nlPBE) to improve the binding mode prediction. We used the well-studied thebarnase-barstarsystem to validate the parameters for free energy calculations. Besides,thenlPBE-based free energy calculations were conducted for the badly predicted cases by ZDOCK and ZRANK. We found that direct molecular mechanics energetics cannot be used to discriminate the native binding pose from the decoys.Our results indicate that nlPBE-based calculations appeared to be one of the promising approaches for improving the success rate of binding pose predictions.
Abstract: We developed a multi-camera control system that a (one) cameraman can operate several cameras at a compact studio. we analyzed a workflow of a cameraman of some program shootings with two cameras and clarified their heavy tasks. The system based on a dynamic workflow which adapts a program progressing and recommends of cameraman. we perform the automation of multicamera controls by modeling of studio environment and perform automatic camera adjustment for suitable angle of view with face detection. Our experiment at a real program shooting showed that one cameraman can carry out the task of shooting sufficiently.
Abstract: This paper presents a new study on the applications of
optimization and regression analysis techniques for optimal
calculation of partial ratios of four-step helical gearboxes for getting
minimal gearbox length. In the paper, basing on the moment
equilibrium condition of a mechanic system including four gear units
and their regular resistance condition, models for determination of the
partial ratios of the gearboxes are proposed. In particular, explicit
models for calculation of the partial ratios are proposed by using
regression analysis. Using these models, the determination of the
partial ratios is accurate and simple.
Abstract: In this research paper, a slotted coaxial line fed cross
dipole excitation structure for short backfire antenna is proposed and
developed to achieve reconfigurable circular polarization. The cross
dipole, which is fed by the slotted coaxial line, consists of two
orthogonal dipoles. The dipoles are mounted on the outer conductor
of the coaxial line. A unique technique is developed to generate
reconfigurable circular polarization using cross dipole configuration.
The sub-reflector is supported by the feed line, thus requiring no
extra support. The antenna is developed on elliptical ground plane
with dielectric rim making antenna compact. It is demonstrated that
cross dipole excited short backfire antenna can achieve voltage
standing wave ratio (VSWR) bandwidth of 14.28% for 2:1 VSWR,
axial ratio of 0.2 dB with axial ratio (≤ 3dB) bandwidth of 2.14% and
a gain of more than 12 dBi. The experimental results for the designed
antenna structure are in close agreement with computer simulations.
Abstract: This paper presents a smart-card applet that is able to
verify X.509 certificates and to use the public key contained in the
certificate for verifying digital signatures that have been created
using the corresponding private key, e.g. for the purpose of authenticating
the certificate owner against the card. The approach has been
implemented as an operating prototype on Java cards.
Abstract: The tensile properties of Mg-3%Al nanocrystalline
alloys were investigated at different test environment. Bulk
nanocrystalline samples of these alloy was successfully prepared by
mechanical alloying (MA) followed by cold compaction, sintering,
and hot extrusion process. The crystal size of the consolidated milled
sample was calculated by X-Ray line profile analysis. The
deformation mechanism and microstructural characteristic at
different test condition was discussed extensively. At room
temperature, relatively lower value of activation volume (AV) and
higher value of strain rate sensitivity (SRS) suggests that new rate
controlling mechanism accommodating plastic flow in the present
nanocrystalline sample. The deformation behavior and the
microstructural character of the present samples were discussed in
details.
Abstract: Work ethic and labour productivity issues are
extremely important for any society. It has been long proven by the
global practice and various scholars that the country promoting the
labour has always been way forward from the other countries. This
paper studies the thoughts suggested by M.Weber, Confucius, Lee
Kuan Yew, Mahathir Mohammad and other prominent thinkers
concerning the issues of work ethics and labour productivity. The
article analyzes why developed nations are way more advanced in
their development compared to other nations.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: In this paper, the optical generation of three bands of
continuously tunable millimeter-wave signals using an optical phase
modulator (OPM) and a polarization state rotation filter (PSRF) as an
optical notch filter is analyzed. The effect of the chromatic dispersion
on millimeter-wave signals is presented.
Abstract: The objectives of this research were to explore factors
influencing knowledge management process in the manufacturing
industry and develop a model to support knowledge management
processes. The studied factors were technology infrastructure, human
resource, knowledge sharing, and the culture of the organization. The
knowledge management processes included discovery, capture,
sharing, and application. Data were collected through questionnaires
and analyzed using multiple linear regression and multiple
correlation. The results found that technology infrastructure, human
resource, knowledge sharing, and culture of the organization
influenced the discovery and capture processes. However, knowledge
sharing had no influence in sharing and application processes. A
model to support knowledge management processes was developed,
which indicated that sharing knowledge needed further improvement
in the organization.
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: Combined therapy using Interferon and Ribavirin is the standard treatment in patients with chronic hepatitis C. However, the number of responders to this treatment is low, whereas its cost and side effects are high. Therefore, there is a clear need to predict patient’s response to the treatment based on clinical information to protect the patients from the bad drawbacks, Intolerable side effects and waste of money. Different machine learning techniques have been developed to fulfill this purpose. From these techniques are Associative Classification (AC) and Decision Tree (DT). The aim of this research is to compare the performance of these two techniques in the prediction of virological response to the standard treatment of HCV from clinical information. 200 patients treated with Interferon and Ribavirin; were analyzed using AC and DT. 150 cases had been used to train the classifiers and 50 cases had been used to test the classifiers. The experiment results showed that the two techniques had given acceptable results however the best accuracy for the AC reached 92% whereas for DT reached 80%.
Abstract: In this paper we present a novel error model for
packet loss and subsequent error description. The proposed model
simulates the error performance of wireless communication link. The
model is designed as two independent Markov chains, where the first
one is used for packet generation and the second one generates
correctly and incorrectly transmitted bits for received packets from
the first chain. The statistical analyses of real communication on the
wireless link are used for determination of model-s parameters. Using
the obtained parameters and the implementation of the generator, we
collected generated traffic. The obtained results generated by
proposed model are compared with the real data collection.
Abstract: In view of growing competition in the service sector,
services are as much in need of modeling, analysis and improvement
as business or working processes. Graphical process models are
important means to capture process-related know-how for an
effective management of the service process. In this contribution, a
human performance analysis of process model development paying
special attention to model development time and the working method
was conducted. It was found that modelers with higher application
experience need significantly less time for mental activities than
modelers with lower application experience, spend more time on
labeling graphical elements, and achieved higher process model
quality in terms of activity label quality.
Abstract: This paper presents a solution for a robotic
manipulation problem. We formulate the problem as combining
target identification, tracking and interception. The task in our
solution is sensing a target on a conveyor belt and then intercepting
robot-s end-effector at a convenient rendezvous point. We used
an object recognition method which identifies the target and finds
its position from visualized scene picture, then the robot system
generates a solution for rendezvous problem using the target-s initial
position and belt velocity . The interception of the target and the
end-effector is executed at a convenient rendezvous point along the
target-s calculated trajectory. Experimental results are obtained using
a real platform with an industrial robot and a vision system over it.
Abstract: Estimates of temperature values at a specific time of day, from daytime and daily profiles, are needed for a number of environmental, ecological, agricultural and technical applications, ranging from natural hazards assessments, crop growth forecasting to design of solar energy systems. The scope of this research is to investigate the efficiency of data mining techniques in estimating minimum, maximum and mean temperature values. For this reason, a number of experiments have been conducted with well-known regression algorithms using temperature data from the city of Patras in Greece. The performance of these algorithms has been evaluated using standard statistical indicators, such as Correlation Coefficient, Root Mean Squared Error, etc.