Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: Nitrogen loss from irrigated cropland, particularly
sandy soils, significantly contributes to nitrate (NO3
-) levels in
surface and groundwaters. Thus, it is of great interest to use
inexpensive natural products that can increase the fertilizer efficiency
and decrease nitrate leaching. In this study, the ability of natural
Iranian zeolite clinoptilolite (Cp) and surfactant modified zeolite
clinoptilolite (SMZ) to remove NH4
+ and NO3
-, respectively, from
aqueous solutions was determined. The feasibility of using Cp and
SMZ as soil amendment to reduce nitrate leaching from soil using
lysimeters was also investigated. Zeolite showed 10.23% to 88.42%
NH4
+ removal efficiency over a wide range of initial NH4
+
concentrations. Nitrate removal efficiency by SMZ was 32.26% to
82.26%. Field study results showed that Cp and SMZ significantly (p
< 0.05) reduced leachate NO3-N concentration compared to control.
There was no significant difference between maximum and mean
leachate NO3-N concentration of SMZ lysimeters and those of Cp
lysimeters.
Abstract: In the present research, the titanium-catalyzed
ethylene dimerization and more specifically, the concomitant byproducts
and polymer formation have been studied in the presence of 2,5-dimethoxytetrahydrofuran as an electron donor compound in the
combination with triethylaluminium (TEA) as activator. Then, we
added ethylene chlorobromide as a new efficient promoter to the
relevant catalyst system. Finally, the behavior of novel homogeneous
[Titanium tetrabutoxide (Ti(OC4H9)4)/2,5-dimethoxytetrahydrofuran/
TEA/ethylene chlorobromide] was investigated in the various
operating conditions for the optimum production of 1-butene. In the
optimum conditions, a very high ethylene conversion (almost 90.77
%), a relative high selectivity to 1-butene (79.00 %), yield of reaction equal to 71.70 % and a significant productivity (turnover frequency
equal to 1370 h-1) were achieved.
Abstract: This work concerns the measurements of a Bulk
Acoustic Waves (BAW) emission filter S parameters and compare
with prototypes simulated types. Thanks to HP-ADS, a co-simulation
of filters- characteristics in a digital radio-communication chain is
performed. Four cases of modulation schemes are studied in order to
illustrate the impact of the spectral occupation of the modulated
signal. Results of simulations and co-simulation are given in terms of
Error Vector Measurements to be useful for a general sensibility
analysis of 4th/3rd Generation (G.) emitters (wideband QAM and
OFDM signals)
Abstract: Citizens are increasingly are provided with choice and
customization in public services and this has now also become a key
feature of higher education in terms of policy roll-outs on personal
development planning (PDP) and more generally as part of the
employability agenda. The goal here is to transform people, in this
case graduates, into active, responsible citizen-workers. A key part of
this rhetoric and logic is the inculcation of graduate attributes within
students. However, there has also been a concern with the issue of
student lack of engagement and perseverance with their studies. This
paper sets out to explore some of these conceptions that link graduate
attributes with citizenship as well as the notion of how identity is
forged through the higher education process. Examples are drawn
from a quality enhancement project that is being operated within the
context of the Scottish higher education system. This is further
framed within the wider context of competing and conflicting
demands on higher education, exacerbated by the current worldwide
economic climate. There are now pressures on students to develop
their employability skills as well as their capacity to engage with
global issues such as behavioural change in the light of
environmental concerns. It is argued that these pressures, in effect,
lead to a form of personalization that is concerned with how
graduates develop their sense of identity as something that is
engineered and re-engineered to meet these demands.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: The production and consumption of natural gas is on
the rise throughout the world as a result of its wide availability, ease
of transportation, use and clean-burning characteristics. The chief use
of ethane is in the chemical industry in the production of Ethene
(ethylene) by steam cracking. In this simulation, obtained ethane
recovery percent based on Gas sub-cooled process (GSP) is 99.9 by
mole that is included 32.1% by using de-methanizer column and
67.8% by de-ethanizer tower. The outstanding feature of this process
is the novel split-vapor concept that employs to generate reflux for
de-methanizer column. Remain amount of ethane in export gas cause
rise in gross heating value up to 36.66 MJ/Nm3 in order to use in
industrial and household consumptions.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: The present research focus on the processing of mullite-based ceramics from oil refinery industrial wastes and byproducts of agricultural industry and on the investigating of silane modified surface of ceramics. Two waste products were used as initial material – waste aluminum oxide and waste rice husk. The burning - out additives used were waste rise husk. It is known that the oxide ceramics surface is hydrophilic due to the presence of – OH groups in it. The nature of ceramic surface regarding permeation of water and hydrocarbons can be changed by further treatment with silanes. The samples were studied mainly by X-ray analysis, FT-IR absorbance measurements and microscopic analysis. The X-ray analyses showed the phase composition depends on the firing temperature and on the purity of the starting alumina. Two kind of silanes were used for the transformation of surface from hydrophilic to hydrophobic – trimethoxymethylsilane (TMMS) and trimethylclorsilane (TMCS).
Abstract: A pilot plant for continuous flow microwave-assisted
chemical reaction combined with microreactors was developed and
water heating tests were conducted for evaluation of the developed
plant. We developed a microwave apparatus having a single
microwave generator that can heat reaction solutions in four reaction
fields simultaneously in order to increase throughput. We also
designed a four-branch waveguide using electromagnetic simulation,
and found that the transmission efficiency at 99%. Finally, we
developed the pilot plant using the developed microwave apparatus
and conducted water heating tests. The temperatures in the respective
reaction fields were controlled within ±1.1 K at 353.2 K. Moreover,
the energy absorption rates by the water were about 90% in the
respective reaction fields, whereas the energy absorption rate was
about 40% when 100 cm3 of water was heated by a commercially
available multimode microwave chemical reactor.
Abstract: An experimental study is presented on the effect of
Conservation Agriculture (CA) compared to Conventional
Agriculture (ConvA) upon Maize Yield based on split-plot model.
Two factors have been considered: A Factor-Fertilization with two
variants: A1- N40P40 kg/ha and A2- N90P70 kg/ha; B Factor- Crop
protection with 4 variants : B1- 4 treatments, B2-3 treatments, B3- 2
treatments and B4- 1 treatment. In comparison with conventional
agriculture, CA determined lower maize yields. Fertilization is the
key factor determining a yield gain of 973.58 kg/ha in ConvA and
1,123.33 kg/ha in CA. A reduced number of treatments determined a
yield decline. The A-B interaction had a positive effect on maize
yield when a larger amount of fertilizer and 4 or 3 treatments were
applied in ConvA and a benefic in CA for highest fertilization level
and 2 treatments. The B2A2 ConvA variant was the most efficient
leading to 302.67 kg/ha gain while B3A2 CA variant brought 181.33
kg production gain.
Abstract: The flow field within the combustor of scramjet
engine is very complex and poses a considerable challenge in the
design and development of a supersonic combustor with an optimized
geometry. In this paper comprehensive numerical studies on flow
field characteristics of different cavity based scramjet combustors
with transverse injection of hydrogen have been carried out for both
non-reacting and reacting flows. The numerical studies have been
carried out using a validated 2D unsteady, density based 1st-order
implicit k-omega turbulence model with multi-component finite rate
reacting species. The results show a wide variety of flow features
resulting from the interactions between the injector flows, shock
waves, boundary layers, and cavity flows. We conjectured that an
optimized cavity is a good choice to stabilize the flame in the
hypersonic flow, and it generates a recirculation zone in the scramjet
combustor. We comprehended that the cavity based scramjet
combustors having a bearing on the source of disturbance for the
transverse jet oscillation, fuel/air mixing enhancement, and flameholding
improvement. We concluded that cavity shape with
backward facing step and 45o forward ramp is a good choice to get
higher temperatures at the exit compared to other four models of
scramjet combustors considered in this study.
Abstract: Alpinia galanga is rhizome, generally known as
Greater galangal and is selected for isolation of newer constituents
accountable for various therapeutic activities. Present study is
intended to isolate glycoside from Alpinia galanga rhizomes. Alpinia
galanga methanolic extract was column chromatograph and eluted
with ethyl acetate-methanol (99:1) to isolate compound β-Sitosterol
Diarabinoside. Herein, the isolation and structural elucidation of new
compound is described. Chemical investigation of methanolic extract
of rhizomes of Alpinia galanga furnished a new compound β-
Sitosterol Diarabinoside. The IR, NMR and MASS investigations of
isolated compound confirmed its structure as β-Sitosterol
Diarabinoside, which is isolated for the first time from a medicinal
plant or any synthetic source.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.
Abstract: Shirvan is located in plain in Northern Khorasan province north east of Iran and has semiarid to temperate climate. To investigate the annual changes in some qualitative parameters such as electrical conductivity, total dissolved solids and chloride concentrations which have increased during ten continuous years. Fourteen groundwater sources including deep as well as semi-deep wells were sampled and were analyzed using standard methods. The trends of obtained data were analyzed during these years and the effects of different factors on the changes in electrical conductivity, concentration of chloride and total dissolved solids were clarified. The results showed that the amounts of some qualitative parameters have been increased during 10 years time which has led to decrease in water quality. The results also showed that increased in urban populations as well as extensive industrialization in the studied area are the most important reasons to influence underground water quality. Furthermore decrease in water quantity is also evident due to more water utilization and occurrence of recent droughts in the region during recent years.
Abstract: Hazard rate estimation is one of the important topics
in forecasting earthquake occurrence. Forecasting earthquake
occurrence is a part of the statistical seismology where the main
subject is the point process. Generally, earthquake hazard rate is
estimated based on the point process likelihood equation called the
Hazard Rate Likelihood of Point Process (HRLPP). In this research,
we have developed estimation method, that is hazard rate single
decrement HRSD. This method was adapted from estimation method
in actuarial studies. Here, one individual associated with an
earthquake with inter event time is exponentially distributed. The
information of epicenter and time of earthquake occurrence are used
to estimate hazard rate. At the end, a case study of earthquake hazard
rate will be given. Furthermore, we compare the hazard rate between
HRLPP and HRSD method.
Abstract: This paper deals with the project selection problem. Project selection problem is one of the problems arose firstly in the field of operations research following some production concepts from primary product mix problem. Afterward, introduction of managerial considerations into the project selection problem have emerged qualitative factors and criteria to be regarded as well as quantitative ones. To overcome both kinds of criteria, an analytic network process is developed in this paper enhanced with fuzzy sets theory to tackle the vagueness of experts- comments to evaluate the alternatives. Additionally, a modified version of Least-Square method through a non-linear programming model is augmented to the developed group decision making structure in order to elicit the final weights from comparison matrices. Finally, a case study is considered by which developed structure in this paper is validated. Moreover, a sensitivity analysis is performed to validate the response of the model with respect to the condition alteration.
Abstract: This contribution aims to outline some topics around the process of introduction of compulsory electronic exchange of documents (so called e-Boxes) in public administration. The research was conducted in order to gauge the difference between the expectation of those using internal email and their experience in reality. Both qualitative and quantitative research is employed to lead also to an estimation of the willingness and readiness of government bodies, business units and citizens to adopt new technologies. At the same time the most potent barriers to successful e-communication through the e-Boxes are identified.
Abstract: The knee bracing steel frame (KBF) is a new kind of energy dissipating frame, which combines excellent ductility and lateral stiffness. In this framing system, a special form of diagonal brace connected to a knee element instead of beam-column joint, is investigated. Recently, a similar system was proposed and named as chevron knee bracing system (CKB) which in comparison with the former system has a better energy absorption characteristic and at the same time retains the elastic nature of the structures. Knee bracing can provide a stiffer bracing system but reduces the ductility of the steel frame. Chevron knee bracing can be employed to provide the desired ductility level for a design. In this article, relation between seismic performance and structural parameters of the two above mentioned systems are investigated and compared. Frames with similar dimensions but various heights in both systems are designed according to Iranian code of practice for seismic resistant design of building, and then based on a non-linear push over static analysis; the seismic parameters such as behavior factor and performance levels are compared.
Abstract: This paper presents the adaptation of the knowledge management model and intellectual capital measurement NOVA to the needs of work or research project must be developed when conducting a program of graduate-level master. Brackets are added in each of the blocks which is represented in the original model NOVA and which allows to represent those involved in each of these.