Abstract: In this paper, a field oriented control (FOC) induction motor drive is presented. In order to eliminate the speed sensor, an adaptation algorithm for tuning the rotor speed is proposed. Based on the Model Reference Adaptive System (MRAS) scheme, the rotor speed is tuned to obtain an exact FOC induction motor drive. The reference and adjustable models, developed in stationary stator reference frame, are used in the MRAS scheme to estimate induction rotor speed from measured terminal voltages and currents. The Integral Proportional (IP) gains speed controller are tuned by a modern approach that is the Particle Swarm Optimization (PSO) algorithm in order to optimize the parameters of the IP controller. The use of PSO as an optimization algorithm makes the drive robust, with faster dynamic response, higher accuracy and insensitive to load variation. The proposed algorithm has been tested by numerical simulation, showing the capability of driving load.
Abstract: This research presents the development of simulation
modeling for WIP management in semiconductor fabrication.
Manufacturing simulation modeling is needed for productivity
optimization analysis due to the complex process flows involved
more than 35 percent re-entrance processing steps more than 15 times
at same equipment. Furthermore, semiconductor fabrication required
to produce high product mixed with total processing steps varies from
300 to 800 steps and cycle time between 30 to 70 days. Besides the
complexity, expansive wafer cost that potentially impact the
company profits margin once miss due date is another motivation to
explore options to experiment any analysis using simulation
modeling. In this paper, the simulation model is developed using
existing commercial software platform AutoSched AP, with
customized integration with Manufacturing Execution Systems
(MES) and Advanced Productivity Family (APF) for data collections
used to configure the model parameters and data source. Model
parameters such as processing steps cycle time, equipment
performance, handling time, efficiency of operator are collected
through this customization. Once the parameters are validated, few
customizations are made to ensure the prior model is executed. The
accuracy for the simulation model is validated with the actual output
per day for all equipments. The comparison analysis from result of
the simulation model compared to actual for achieved 95 percent
accuracy for 30 days. This model later was used to perform various
what if analysis to understand impacts on cycle time and overall
output. By using this simulation model, complex manufacturing
environment like semiconductor fabrication (fab) now have
alternative source of validation for any new requirements impact
analysis.
Abstract: In this paper we compare the accuracy of data mining
methods to classifying students in order to predicting student-s class
grade. These predictions are more useful for identifying weak
students and assisting management to take remedial measures at early
stages to produce excellent graduate that will graduate at least with
second class upper. Firstly we examine single classifiers accuracy on
our data set and choose the best one and then ensembles it with a
weak classifier to produce simple voting method. We present results
show that combining different classifiers outperformed other single
classifiers for predicting student performance.
Abstract: In this paper, we study on color transformation
method on website images for the color blind. The most common
category of color blindness is red-green color blindness which is
viewed as beige color. By transforming the colors of the images, the
color blind can improve their color visibility. They can have a better
view when browsing through the websites. To transform colors on
the website images, we study on two algorithms which are the
conversion techniques from RGB color space to HSV color space and
self-organizing color transformation. The comparative study focuses
on criteria based on the ease of use, quality, accuracy and efficiency.
The outcome of the study leads to enhancement of website images to
meet the color blinds- vision requirements in perceiving image
detailed.
Abstract: A measurement system for pH array sensors is
introduced to increase accuracy, and decrease non-ideal effects
successfully. An array readout circuit reads eight potentiometric
signals at the same time, and obtains an average value. The deviation
value or the extreme value is counteracted and the output voltage is a
relatively stable value. The errors of measuring pH buffer solutions are
decreased obviously with this measurement system, and the non-ideal
effects, drift and hysteresis, are lowered to 1.638mV/hr and 1.118mV,
respectively. The efficiency and stability are better than single sensor.
The whole sensing characteristics are improved.
Abstract: In this paper, solution of fuzzy differential equation
under general differentiability is obtained by genetic programming
(GP). The obtained solution in this method is equivalent or very close
to the exact solution of the problem. Accuracy of the solution to this
problem is qualitatively better. An illustrative numerical example is
presented for the proposed method.
Abstract: Texture information plays increasingly an important
role in remotely sensed imagery classification and many pattern
recognition applications. However, the selection of relevant textural
features to improve this classification accuracy is not a straightforward
task. This work investigates the effectiveness of two Mutual
Information Feature Selector (MIFS) algorithms to select salient
textural features that contain highly discriminatory information for
multispectral imagery classification. The input candidate features are
extracted from a SPOT High Resolution Visible(HRV) image using
Wavelet Transform (WT) at levels (l = 1,2).
The experimental results show that the selected textural features
according to MIFS algorithms make the largest contribution to
improve the classification accuracy than classical approaches such
as Principal Components Analysis (PCA) and Linear Discriminant
Analysis (LDA).
Abstract: The Emergency Department of a medical center in
Taiwan cooperated to conduct the research. A predictive model of
triage system is contracted from the contract procedure, selection of
parameters to sample screening. 2,000 pieces of data needed for the
patients is chosen randomly by the computer. After three
categorizations of data mining (Multi-group Discriminant Analysis,
Multinomial Logistic Regression, Back-propagation Neural
Networks), it is found that Back-propagation Neural Networks can
best distinguish the patients- extent of emergency, and the accuracy
rate can reach to as high as 95.1%. The Back-propagation Neural
Networks that has the highest accuracy rate is simulated into the triage
acuity expert system in this research. Data mining applied to the
predictive model of the triage acuity expert system can be updated
regularly for both the improvement of the system and for education
training, and will not be affected by subjective factors.
Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: The primary objective of this paper was to construct a
“kinematic parameter-independent modeling of three-axis machine
tools for geometric error measurement" technique. Improving the
accuracy of the geometric error for three-axis machine tools is one of
the machine tools- core techniques. This paper first applied the
traditional method of HTM to deduce the geometric error model for
three-axis machine tools. This geometric error model was related to the
three-axis kinematic parameters where the overall errors was relative
to the machine reference coordinate system. Given that the
measurement of the linear axis in this model should be on the ideal
motion axis, there were practical difficulties. Through a measurement
method consolidating translational errors and rotational errors in the
geometric error model, we simplified the three-axis geometric error
model to a kinematic parameter-independent model. Finally, based on
the new measurement method corresponding to this error model, we
established a truly practical and more accurate error measuring
technique for three-axis machine tools.
Abstract: The main goal of the study is to analyze all relevant properties of the electro hydraulic systems and based on that to make a proper choice of the neural network control strategy that may be used for the control of the mechatronic system. A combination of electronic and hydraulic systems is widely used since it combines the advantages of both. Hydraulic systems are widely spread because of their properties as accuracy, flexibility, high horsepower-to-weight ratio, fast starting, stopping and reversal with smoothness and precision, and simplicity of operations. On the other hand, the modern control of hydraulic systems is based on control of the circuit fed to the inductive solenoid that controls the position of the hydraulic valve. Since this circuit may be easily handled by PWM (Pulse Width Modulation) signal with a proper frequency, the combination of electrical and hydraulic systems became very fruitful and usable in specific areas as airplane and military industry. The study shows and discusses the experimental results obtained by the control strategy of neural network control using MATLAB and SIMULINK [1]. Finally, the special attention was paid to the possibility of neuro-controller design and its application to control of electro-hydraulic systems and to make comparative with other kinds of control.
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: Breast skin-line estimation and breast segmentation is an important pre-process in mammogram image processing and computer-aided diagnosis of breast cancer. Limiting the area to be processed into a specific target region in an image would increase the accuracy and efficiency of processing algorithms. In this paper we are presenting a new algorithm for estimating skin-line and breast segmentation using fast marching algorithm. Fast marching is a partial-differential equation based numerical technique to track evolution of interfaces. We have introduced some modifications to the traditional fast marching method, specifically to improve the accuracy of skin-line estimation and breast tissue segmentation. Proposed modifications ensure that the evolving front stops near the desired boundary. We have evaluated the performance of the algorithm by using 100 mammogram images taken from mini-MIAS database. The results obtained from the experimental evaluation indicate that this algorithm explains 98.6% of the ground truth breast region and accuracy of the segmentation is 99.1%. Also this algorithm is capable of partially-extracting nipple when it is available in the profile.
Abstract: Along with the advances in medicine, providing medical information to individual patient is becoming more important. In Japan such information via Braille is hardly provided to blind and partially sighted people. Thus we are researching and developing a Web-based automatic translation program “eBraille" to translate Japanese text into Japanese Braille. First we analyzed the Japanese transcription rules to implement them on our program. We then added medical words to the dictionary of the program to improve its translation accuracy for medical text. Finally we examined the efficacy of statistical learning models (SLMs) for further increase of word segmentation accuracy in braille translation. As a result, eBraille had the highest translation accuracy in the comparison with other translation programs, improved the accuracy for medical text and is utilized to make hospital brochures in braille for outpatients and inpatients.
Abstract: Hemorrhage Disease of Grass Carp (HDGC) is a kind
of commonly occurring illnesses in summer, and the extremely high
death rate result in colossal losses to aquaculture. As the complex
connections among each factor which influences aquiculture diseases,
there-s no quit reasonable mathematical model to solve the problem at
present.A BP neural network which with excellent nonlinear mapping
coherence was adopted to establish mathematical model;
Environmental factor, which can easily detected, such as breeding
density, water temperature, pH and light intensity was set as the main
analyzing object. 25 groups of experimental data were used for
training and test, and the accuracy of using the model to predict the
trend of HDGC was above 80%. It is demonstrated that BP neural
network for predicating diseases in HDGC has a particularly
objectivity and practicality, thus it can be spread to other aquiculture
disease.
Abstract: A minimal complexity version of component mode
synthesis is presented that requires simplified computer
programming, but still provides adequate accuracy for modeling
lower eigenproperties of large structures and their transient
responses. The novelty is that a structural separation into components
is done along a plane/surface that exhibits rigid-like behavior, thus
only normal modes of each component is sufficient to use, without
computing any constraint, attachment, or residual-attachment modes.
The approach requires only such input information as a few (lower)
natural frequencies and corresponding undamped normal modes of
each component. A novel technique is shown for formulation of
equations of motion, where a double transformation to generalized
coordinates is employed and formulation of nonproportional damping
matrix in generalized coordinates is shown.
Abstract: Hidden Markov Model (HMM) is a stochastic method
which has been used in various signal processing and character
recognition. This study proposes to use HMM to recognize Javanese
characters from a number of different handwritings, whereby HMM
is used to optimize the number of state and feature extraction. An
85.7 % accuracy is obtained as the best result in 16-stated vertical
model using pure HMM. This initial result is satisfactory for
prompting further research.
Abstract: Digital news with a variety topics is abundant on the
internet. The problem is to classify news based on its appropriate
category to facilitate user to find relevant news rapidly. Classifier
engine is used to split any news automatically into the respective
category. This research employs Support Vector Machine (SVM) to
classify Indonesian news. SVM is a robust method to classify
binary classes. The core processing of SVM is in the formation of an
optimum separating plane to separate the different classes. For
multiclass problem, a mechanism called one against one is used to
combine the binary classification result. Documents were taken
from the Indonesian digital news site, www.kompas.com. The
experiment showed a promising result with the accuracy rate of 85%.
This system is feasible to be implemented on Indonesian news
classification.
Abstract: In this paper, a numerical solution based on sinc
functions is used for finding the solution of boundary value problems
which arise from the problems of calculus of variations. This
approximation reduce the problems to an explicit system of algebraic
equations. Some numerical examples are also given to illustrate the
accuracy and applicability of the presented method.
Abstract: Computerized lip reading has been one of the most
actively researched areas of computer vision in recent past because
of its crime fighting potential and invariance to acoustic environment.
However, several factors like fast speech, bad pronunciation,
poor illumination, movement of face, moustaches and beards make
lip reading difficult. In present work, we propose a solution for
automatic lip contour tracking and recognizing letters of English
language spoken by speakers using the information available from
lip movements. Level set method is used for tracking lip contour
using a contour velocity model and a feature vector of lip movements
is then obtained. Character recognition is performed using modified
k nearest neighbor algorithm which assigns more weight to nearer
neighbors. The proposed system has been found to have accuracy
of 73.3% for character recognition with speaker lip movements as
the only input and without using any speech recognition system in
parallel. The approach used in this work is found to significantly
solve the purpose of lip reading when size of database is small.