Abstract: DNA shuffling is a powerful method used for in vitro
evolute molecules with specific functions and has application in areas
such as, for example, pharmaceutical, medical and agricultural
research. The success of such experiments is dependent on a variety
of parameters and conditions that, sometimes, can not be properly
pre-established. Here, two computational models predicting DNA
shuffling results is presented and their use and results are evaluated
against an empirical experiment. The in silico and in vitro results
show agreement indicating the importance of these two models and
motivating the study and development of new models.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: The line start permanent magnet motor (LSPMM)
combines a permanent magnet rotor for a better motor efficiency
during synchronous running with an induction motor squirrel cage
rotor to permit the motor starting by direct coupling to power source.
In this paper effect of the rotor structure on a line start synchronous
permanent magnet motor (LSPMM) is analyzed. LSPMM motor with
three different structures for rotor is designed by using RMxprt
software; efficiency and line current of LSPMM motor for different
structures in full-load condition have been presented. The results
indicate that with correct choosing of rotor structure, maximum
efficiency can be found.
Abstract: An optimal power flow (OPF) based on particle swarm
optimization (PSO) was developed with more realistic generator
security constraint using the capability curve instead of only Pmin/Pmax
and Qmin/Qmax. Neural network (NN) was used in designing digital
capability curve and the security check algorithm. The algorithm is
very simple and flexible especially for representing non linear
generation operation limit near steady state stability limit and under
excitation operation area. In effort to avoid local optimal power flow
solution, the particle swarm optimization was implemented with
enough widespread initial population. The objective function used in
the optimization process is electric production cost which is
dominated by fuel cost. The proposed method was implemented at
Java Bali 500 kV power systems contain of 7 generators and 20
buses. The simulation result shows that the combination of generator
power output resulted from the proposed method was more economic
compared with the result using conventional constraint but operated
at more marginal operating point.
Abstract: This study aimed to detect and to identify the main
strains of airborne microorganisms present in the Shanghai Metro
system. Samples were collected using agar plates exposed to the air
and microorganisms were identified using catalase, plasma coagulase
and hymolytic analysis. The results show that the concentration of
mildew present within a newly opened metro line was significantly
higher than for other lines. Differences among underground and
elevated stations can be attributed to differences in passenger flow and
the environment surrounding the stations. Additionally, the
investigation indicated that bacteria reached maximum levels at
different times on weekdays and weekends. The bacteria in the Metro
stations were identified as primarily Gram positive, consisting mainly
of coagulase-negative staphylococcus strains (CNS).
Abstract: In India, the quarrel between the budding human
populace and the planet-s unchanging supply of freshwater and
falling water tables has strained attention the reuse of gray water as
an alternative water resource in rural development. This paper
present the finest design of laboratory scale gray water treatment
plant, which is a combination of natural and physical operations such
as primary settling with cascaded water flow, aeration, agitation and
filtration, hence called as hybrid treatment process. The economical
performance of the plant for treatment of bathrooms, basins and
laundries gray water showed in terms of deduction competency of
water pollutants such as COD (83%), TDS (70%), TSS (83%), total
hardness (50%), oil and grease (97%), anions (46%) and cations
(49%). Hence, this technology could be a good alternative to treat
gray water in residential rural area.
Abstract: This paper applies Bayesian Networks to support
information extraction from unstructured, ungrammatical, and
incoherent data sources for semantic annotation. A tool has been
developed that combines ontologies, machine learning, and
information extraction and probabilistic reasoning techniques to
support the extraction process. Data acquisition is performed with the
aid of knowledge specified in the form of ontology. Due to the
variable size of information available on different data sources, it is
often the case that the extracted data contains missing values for
certain variables of interest. It is desirable in such situations to
predict the missing values. The methodology, presented in this paper,
first learns a Bayesian network from the training data and then uses it
to predict missing data and to resolve conflicts. Experiments have
been conducted to analyze the performance of the presented
methodology. The results look promising as the methodology
achieves high degree of precision and recall for information
extraction and reasonably good accuracy for predicting missing
values.
Abstract: This study is concerned with a new adaptive impedance control strategy to compensate for unknown time-varying environment stiffness and position. The uncertainties are expressed by Function Approximation Technique (FAT), which allows the update laws to be derived easily using Lyapunov stability theory. Computer simulation results are presented to validate the effectiveness of the proposed strategy.
Abstract: The join dependency provides the basis for obtaining
lossless join decomposition in a classical relational schema. The
existence of Join dependency shows that that the tables always
represent the correct data after being joined. Since the classical
relational databases cannot handle imprecise data, they were
extended to fuzzy relational databases so that uncertain, ambiguous,
imprecise and partially known information can also be stored in
databases in a formal way. However like classical databases, the
fuzzy relational databases also undergoes decomposition during
normalization, the issue of joining the decomposed fuzzy relations
remains intact. Our effort in the present paper is to emphasize on this
issue. In this paper we define fuzzy join dependency in the
framework of type-1 fuzzy relational databases & type-2 fuzzy
relational databases using the concept of fuzzy equality which is
defined using fuzzy functions. We use the fuzzy equi-join operator
for computing the fuzzy equality of two attribute values. We also
discuss the dependency preservation property on execution of this
fuzzy equi- join and derive the necessary condition for the fuzzy
functional dependencies to be preserved on joining the decomposed
fuzzy relations. We also derive the conditions for fuzzy join
dependency to exist in context of both type-1 and type-2 fuzzy
relational databases. We find that unlike the classical relational
databases even the existence of a trivial join dependency does not
ensure lossless join decomposition in type-2 fuzzy relational
databases. Finally we derive the conditions for the fuzzy equality to
be non zero and the qualification of an attribute for fuzzy key.
Abstract: This paper presents the experimental results on
artificial ageing test of 22 kV XLPE cable for distribution system
application in Thailand. XLPE insulating material of 22 kV cable
was sliced to 60-70 μm in thick and was subjected to ac high voltage
at 23
Ôùª
C, 60
Ôùª
C and 75
Ôùª
C. Testing voltage was constantly applied to
the specimen until breakdown. Breakdown voltage and time to
breakdown were used to evaluate life time of insulating material.
Furthermore, the physical model by J. P. Crine for predicts life time
of XLPE insulating material was adopted as life time model and was
calculated in order to compare the experimental results. Acceptable
life time results were obtained from Crine-s model comparing with
the experimental result. In addition, fourier transform infrared
spectroscopy (FTIR) for chemical analysis and scanning electron
microscope (SEM) for physical analysis were conducted on tested
specimens.
Abstract: Aptamers are useful tools in microorganism
researches, diagnoses, and treatment. Aptamers are specific target
molecules formed by oligonucleic acid molecules, and are not
decomposed by alcohol. Aptamers used to detect Mycobacterium
tuberculosis (MTB) have been proved to have specific affinity to the
outer membrane proteins of MTB. This article presents a biosensor
chip set with aptamers for early detection of MTB with high specificity
and sensitivity, even in very low concentration. Meanwhile, we have
already made a modified hydrophobic facial mask module with
internal rendering hydrophobic for effectively collecting M.
tuberculosis.
Abstract: In this research paper we have presented control
architecture for robotic arm movement and trajectory planning using
Fuzzy Logic (FL) and Genetic Algorithms (GAs). This architecture is
used to compensate the uncertainties like; movement, friction and
settling time in robotic arm movement. The genetic algorithms and
fuzzy logic is used to meet the objective of optimal control
movement of robotic arm. This proposed technique represents a
general model for redundant structures and may extend to other
structures. Results show optimal angular movement of joints as result
of evolutionary process. This technique has edge over the other
techniques as minimum mathematics complexity used.
Abstract: A scalable QoS aware multicast deployment in
DiffServ networks has become an important research dimension in
recent years. Although multicasting and differentiated services are
two complementary technologies, the integration of the two
technologies is a non-trivial task due to architectural conflicts
between them. A popular solution proposed is to extend the
functionality of the DiffServ components to support multicasting. In
this paper, we propose an algorithm to construct an efficient QoSdriven
multicast tree, taking into account the available bandwidth per
service class. We also present an efficient way to provision the
limited available bandwidth for supporting heterogeneous users. The
proposed mechanism is evaluated using simulated tests. The
simulated result reveals that our algorithm can effectively minimize
the bandwidth use and transmission cost
Abstract: This paper presents a new sensor-based online method for generating collision-free near-optimal paths for mobile robots pursuing a moving target amidst dynamic and static obstacles. At each iteration, first the set of all collision-free directions are calculated using velocity vectors of the robot relative to each obstacle and target, forming the Directive Circle (DC), which is a novel concept. Then, a direction close to the shortest path to the target is selected from feasible directions in DC. The DC prevents the robot from being trapped in deadlocks or local minima. It is assumed that the target's velocity is known, while the speeds of dynamic obstacles, as well as the locations of static obstacles, are to be calculated online. Extensive simulations and experimental results demonstrated the efficiency of the proposed method and its success in coping with complex environments and obstacles.
Abstract: The term hybrid composite refers to the composite
containing more than one type of fiber material as reinforcing fillers.
It has become attractive structural material due to the ability of
providing better combination of properties with respect to single fiber
containing composite. The eco-friendly nature as well as processing
advantage, light weight and low cost have enhanced the attraction
and interest of natural fiber reinforced composite. The objective of
present research is to study the mechanical properties of jute-coir
fiber reinforced hybrid polypropylene (PP) composite according to
filler loading variation. In the present work composites were
manufactured by using hot press machine at four levels of fiber
loading (5, 10, 15 and 20 wt %). Jute and coir fibers were utilized at a
ratio of (1:1) during composite manufacturing. Tensile, flexural,
impact and hardness tests were conducted for mechanical
characterization. Tensile test of composite showed a decreasing trend
of tensile strength and increasing trend of the Young-s modulus with
increasing fiber content. During flexural, impact and hardness tests,
the flexural strength, flexural modulus, impact strength and hardness
were found to be increased with increasing fiber loading. Based on
the fiber loading used in this study, 20% fiber reinforced composite
resulted the best set of mechanical properties.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.
Abstract: By means of the extended homoclinic test approach (shortly EHTA) with the aid of a symbolic computation system such as Maple, some complexiton type solutions for the (3+1)-dimensional Jimbo-Miwa equation are presented.
Abstract: We present a new intuitionistic fuzzy aggregation
operator called the intuitionistic fuzzy ordered weighted
averaging-weighted average (IFOWAWA) operator. The main
advantage of the IFOWAWA operator is that it unifies the OWA
operator with the WA in the same formulation considering the degree
of importance that each concept has in the aggregation. Moreover, it is
able to deal with an uncertain environment that can be assessed with
intuitionistic fuzzy numbers. We study some of its main properties and
we see that it has a lot of particular cases such as the intuitionistic
fuzzy weighted average (IFWA) and the intuitionistic fuzzy OWA
(IFOWA) operator. Finally, we study the applicability of the new
approach on a financial decision making problem concerning the
selection of financial strategies.