Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: Concrete performance is strongly affected by the
particle packing degree since it determines the distribution of the
cementitious component and the interaction of mineral particles. By
using packing theory designers will be able to select optimal
aggregate materials for preparing concrete with low cement content,
which is beneficial from the point of cost. Optimum particle packing
implies minimizing porosity and thereby reducing the amount of
cement paste needed to fill the voids between the aggregate particles,
taking also the rheology of the concrete into consideration. For
reaching good fluidity superplasticizers are required. The results from
pilot tests at Luleå University of Technology (LTU) show various
forms of the proposed theoretical models, and the empirical approach
taken in the study seems to provide a safer basis for developing new,
improved packing models.
Abstract: This paper deals with a new way for designing
external fixators applied in traumatology and orthopaedics. These
fixators can be applied in the treatment of open and unstable
fractures or for lengthening human or animal bones etc. The new
design is based on the development of Ilizarov and other techniques
(i.e. shape and weight optimalization based on composite materials,
application of smart materials, nanotechnology, low x-ray absorption,
antibacterial protection, patient's comfort, reduction in the duration
of the surgical treatment, and cost).
Abstract: The state-of-the-art Bag of Words model in Content-
Based Image Retrieval has been used for years but the relevance
feedback strategies for this model are not fully investigated. Inspired
from text retrieval, the Bag of Words model has the ability to use the
wealth of knowledge and practices available in text retrieval. We
study and experiment the relevance feedback model in text retrieval
for adapting it to image retrieval. The experiments show that the
techniques from text retrieval give good results for image retrieval
and that further improvements is possible.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: In this work study the location of interface in a stirred vessel with a Concave impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: This paper proposes the concept of aerocapture with
aerodynamic-environment-adaptive variable geometry flexible
aeroshell that vehicle deploys. The flexible membrane is composed
of thin-layer film or textile as its aeroshell in order to solve some
problems obstructing realization of aerocapture technique.
Multi-objective optimization study is conducted to investigate
solutions and derive design guidelines. As a result, solutions which
can avoid aerodynamic heating and enlarge the corridor width up
to 10% are obtained successfully, so that the effectiveness of this
concept can be demonstrated. The deformation-use optimum
solution changes its drag coefficient from 1.6 to 1.1, along with the
change in dynamic pressure. Moreover, optimization results show
that deformation-use solution requires the membrane for which
upper temperature limit and strain limit are more than 700 K and
120%, respectively, and elasticity (Young-s modulus) is of order of
106 Pa.
Abstract: Bangladesh is a developing country with large
population. Demand of electrical energy is increasing day by day
because of increasing population and industrialization. But due to
limited resources, people here are suffering from power crisis
problem which is considered as a major obstacle to the economic
development. In most of the cases, it is extremely difficult to extend
high tension transmission lines to some of the places that are
separated from the mainland. Renewable energy is considered to be
the right choice for providing clean energy to these remote
settlements. This paper proposes a cost effective design of off-grid
wind-diesel hybrid power system using combined heat and power
(CHP) technology in a grid isolated island, Sandwip, Bangladesh.
Design and simulation of the wind-diesel hybrid power system is
performed considering different factors for the island Sandwip.
Detailed economic analysis and comparison with solar PV system
clearly reveals that wind-diesel hybrid power system can be a cost
effective solution for the isolated island like Sandwip.
Abstract: Image Searching was always a problem specially when these images are not properly managed or these are distributed over different locations. Currently different techniques are used for image search. On one end, more features of the image are captured and stored to get better results. Storing and management of such features is itself a time consuming job. While on the other extreme if fewer features are stored the accuracy rate is not satisfactory. Same image stored with different visual properties can further reduce the rate of accuracy. In this paper we present a new concept of using polynomials of sorted histogram of the image. This approach need less overhead and can cope with the difference in visual features of image.
Abstract: In this paper, we propose a Perceptually Optimized Embedded ZeroTree Image Coder (POEZIC) that introduces a perceptual weighting to wavelet transform coefficients prior to control SPIHT encoding algorithm in order to reach a targeted bit rate with a perceptual quality improvement with respect to the coding quality obtained using the SPIHT algorithm only. The paper also, introduces a new objective quality metric based on a Psychovisual model that integrates the properties of the HVS that plays an important role in our POEZIC quality assessment. Our POEZIC coder is based on a vision model that incorporates various masking effects of human visual system HVS perception. Thus, our coder weights the wavelet coefficients based on that model and attempts to increase the perceptual quality for a given bit rate and observation distance. The perceptual weights for all wavelet subbands are computed based on 1) luminance masking and Contrast masking, 2) the contrast sensitivity function CSF to achieve the perceptual decomposition weighting, 3) the Wavelet Error Sensitivity WES used to reduce the perceptual quantization errors. The new perceptually optimized codec has the same complexity as the original SPIHT techniques. However, the experiments results show that our coder demonstrates very good performance in terms of quality measurement.
Abstract: This paper presents a hybrid fuzzy-PD plus PID
(HFPP) controller and its application to steam distillation process for
essential oil extraction system. Steam temperature is one of the most
significant parameters that can influence the composition of essential
oil yield. Due to parameter variations and changes in operation
conditions during distillation, a robust steam temperature controller becomes nontrivial to avoid the degradation of essential oil quality.
Initially, the PRBS input is triggered to the system and output of steam temperature is modeled using ARX model structure. The
parameter estimation and tuning method is adopted by simulation
using HFPP controller scheme. The effectiveness and robustness of
proposed controller technique is validated by real time
implementation to the system. The performance of HFPP using 25 and 49 fuzzy rules is compared. The experimental result demonstrates the proposed HFPP using 49 fuzzy rules achieves a
better, consistent and robust controller compared to PID when considering the test on tracking the set point and the effects due to disturbance.
Abstract: We introduce an adaptive technique for the joint mitigation of transients and continuous-wave radio-frequency co-channel interference (CW RFI) in high-frequency (HF) over-the-horizon radars (OTHRs). The performance of this technique is illustrated using data from an operational surface-wave radar (SECAR) and from recent experimental trials with sky-wave (SW) and sky-wave–line-of-sight (SKYLOS) HF OTHRs.
Abstract: Crime is a major societal problem for most of the
world's nations. Consequently, the police need to develop new
methods to improve their efficiency in dealing with these ever increasing crime rates. Two of the common difficulties that the police
face in crime control are crime investigation and the provision of crime information to the general public to help them protect themselves. Crime control in police operations involves the use of
spatial data, crime data and the related crime data from different organizations (depending on the nature of the analysis to be made).
These types of data are collected from several heterogeneous sources
in different formats and from different platforms, resulting in a lack of standardization. Moreover, there is no standard framework for
crime data collection, integration and dissemination through mobile
devices. An investigation into the current situation in crime control was carried out to identify the needs to resolve these issues. This
paper proposes and investigates the use of service oriented
architecture (SOA) and the mobile spatial information service in crime control. SOA plays an important role in crime control as an
appropriate way to support data exchange and model sharing from
heterogeneous sources. Crime control also needs to facilitate mobile
spatial information services in order to exchange, receive, share and release information based on location to mobile users anytime and
anywhere.
Abstract: The possibility of using cassava residue containing
49.66% starch, 21.47% cellulose, 12.97% hemicellulose, and 21.86%
lignin as a raw material to produce glucose using enzymatic
hydrolysis was investigated. In the experiment, each reactor
contained the cassava residue, bacteria cells, and production medium.
The effects of particles size (40 mesh and 60 mesh) and strains of
bacteria (A002 and M015) isolated from Thai higher termites,
Microcerotermes sp., on the glucose concentration at 37°C were
focused. High performance liquid chromatography (HPLC) with a
refractive index detector was used to determine the quantity of
glucose. The maximum glucose concentration obtained at 37°C using
strain A002 and 60 mesh of the cassava residue was 1.51 g/L at 10 h.
Abstract: An interesting method to produce calcium carbonate is based in a gas-liquid reaction between carbon dioxide and aqueous solutions of calcium hydroxide. The design parameters for gas-liquid phase are flow regime, individual mass transfer, gas-liquid specific interfacial area. Most studies on gas-liquid phase were devoted to the experimental determination of some of these parameters, and more specifically, of the mass transfer coefficient, kLa which depends fundamentally on the superficial gas velocity and on the physical properties of absorption phase. The principle investigation was directed to study the effect of the vibration on the mass transfer coefficient kLa in gas-liquid phase during absorption of CO2 in the in aqueous solution of calcium hydroxide. The vibration with a higher frequency increase the mass transfer coefficient kLa, but vibration with lower frequency didn-t improve it, the mass transfer coefficient kLa increase with increase the superficial gas velocity.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: The data exchanged on the Web are of different nature
from those treated by the classical database management systems;
these data are called semi-structured data since they do not have a
regular and static structure like data found in a relational database;
their schema is dynamic and may contain missing data or types.
Therefore, the needs for developing further techniques and
algorithms to exploit and integrate such data, and extract relevant
information for the user have been raised. In this paper we present
the system OSIX (Osiris based System for Integration of XML
Sources). This system has a Data Warehouse model designed for the
integration of semi-structured data and more precisely for the
integration of XML documents. The architecture of OSIX relies on
the Osiris system, a DL-based model designed for the representation
and management of databases and knowledge bases. Osiris is a viewbased
data model whose indexing system supports semantic query
optimization. We show that the problem of query processing on a
XML source is optimized by the indexing approach proposed by
Osiris.