Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: In this paper, we present an innovative scheme of
blindly extracting message bits from an image distorted by an attack.
Support Vector Machine (SVM) is used to nonlinearly classify the
bits of the embedded message. Traditionally, a hard decoder is used
with the assumption that the underlying modeling of the Discrete
Cosine Transform (DCT) coefficients does not appreciably change.
In case of an attack, the distribution of the image coefficients is
heavily altered. The distribution of the sufficient statistics at the
receiving end corresponding to the antipodal signals overlap and a
simple hard decoder fails to classify them properly. We are
considering message retrieval of antipodal signal as a binary
classification problem. Machine learning techniques like SVM is
used to retrieve the message, when certain specific class of attacks is
most probable. In order to validate SVM based decoding scheme, we
have taken Gaussian noise as a test case. We generate a data set using
125 images and 25 different keys. Polynomial kernel of SVM has
achieved 100 percent accuracy on test data.
Abstract: Studies revealing the positive relationship between
trade and income are often criticized with the argument that
“development should mean more than rising incomes". Taking this
argument as a base and utilizing panel data, Davies and Quinlivan [1]
have demonstrated that increases in trade are positively associated
with future increases in social welfare as measured by the Human
Development Index (HDI). The purpose of this study is twofold:
Firstly, utilizing an income based country classification; it is aimed
to investigate whether the positive association between foreign trade
and HDI is valid within all country groups. Secondly, keeping the
same categorization as a base; it is aimed to reveal whether the
positive link between trade and HDI still exists when the income
components of the index are excluded. Employing a panel data
framework of 106 countries, this study reveals that the positive link
between trade and human development is valid only for high and
medium income countries. Moreover, the positive link between trade
and human development diminishes in lower-medium income
countries when only non-income components of the index are taken
into consideration.
Abstract: In the article there have been revealed the properties
of designing the research teaching the military masters and in the context it has been offered the program of mastering by the masters
military men the methodology of research work, in the course of practical teaching activity there has been considered the developed
and approbated model of organization of the process of mastering by the masters the methodology of research work. As a whole, the research direction of master preparation leaves its
sign to the content of education, forms of organization of educational
process, scientific work of masters. In this connection the offered in
the article properties of organization of research teaching and a model
of organization of mastering by the masters military men the methodology of research work can be taken into account when
designing the content of master preparation.
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.
Abstract: In this study, it is investigated the stability boundary of
Functionally Graded (FG) panel under the heats and supersonic
airflows. Material properties are assumed to be temperature
dependent, and a simple power law distribution is taken. First-order
shear deformation theory (FSDT) of plate is applied to model the
panel, and the von-Karman strain- displacement relations are
adopted to consider the geometric nonlinearity due to large
deformation. Further, the first-order piston theory is used to model the
supersonic aerodynamic load acting on a panel and Rayleigh damping
coefficient is used to present the structural damping. In order to find a
critical value of the speed, linear flutter analysis of FG panels is
performed. Numerical results are compared with the previous works,
and present results for the temperature dependent material are
discussed in detail for stability boundary of the panel with various
volume fractions, and aerodynamic pressures.
Abstract: Steganography meaning covered writing. Steganography includes the concealment of information within computer files [1]. In other words, it is the Secret communication by hiding the existence of message. In this paper, we will refer to cover image, to indicate the images that do not yet contain a secret message, while we will refer to stego images, to indicate an image with an embedded secret message. Moreover, we will refer to the secret message as stego-message or hidden message. In this paper, we proposed a technique called RGB intensity based steganography model as RGB model is the technique used in this field to hide the data. The methods used here are based on the manipulation of the least significant bits of pixel values [3][4] or the rearrangement of colors to create least significant bit or parity bit patterns, which correspond to the message being hidden. The proposed technique attempts to overcome the problem of the sequential fashion and the use of stego-key to select the pixels.
Abstract: In this paper, a class of impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms is formulated and investigated. By employing the delay differential inequality and inequality technique developed by Xu et al., some sufficient conditions ensuring the existence, uniqueness and global exponential stability of equilibrium point for impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms are obtained. In particular, the estimate of the exponential convergence rate is also provided, which depends on system parameters, diffusion effect and impulsive disturbed intention. It is believed that these results are significant and useful for the design and applications of BAM fuzzy cellular neural networks. An example is given to show the effectiveness of the results obtained here.
Abstract: Implementation of response surface methodology (RSM) was employed to study the effects of two factor (rubber clearance and round per minute) in brown rice peeling machine of The optimal BROKENS yield (19.02, average of three repeats),.The optimized composition derived from RSM regression was analyzed using Regression analysis and Analysis of Variance (ANOVA). At a significant level α = 0.05, the values of Regression coefficient, R 2 (adj)were 97.35 % and standard deviation were 1.09513. The independent variables are initial rubber clearance, and round per minute parameters namely. The investigating responses are final rubber clearance, and round per minute (RPM). The restriction of the optimization is the designated.
Abstract: The research was set up on chernozem soil at the Látókép AGTC MÉK research area of the University of Debrecen in Hungary. We examined the yield, the yield production per 1kg NPK fertilizer and the water and nutrient utilization of hybrid PR37N01 and PR37M81 in 2013. We found that PR37N01 produced the most yield at the level of N120+P (17,476kg ha-1) while PR37M81 reached the highest yield at level N150+PK (16,754kg ha-1). Studies related to yield production per 1kg NPK indicated that the best results were achieved at level N30+PK compared to the control treatment. Yield production per 1kg NPK was17.6kg kg-1 by P37N01 and 44.2kg kg-1 by PR37M81. By comparing the water utilization of hybrids we found that the worst water utilization results were reached in the control treatment (PR37N01: 26.2kg mm-1, PR37M81: 19.5kg mm-1). The best water utilization values were produced at level N120+PK in the case of hybrid PR37N01 (32.1kg mm-1) and at N150+PK in the case of hybrid PR37M81 (30.8kg mm-1). We established the values of the nutrient reaction and the fertilizer optimum of hybrids. We discovered a strong relationship between the amount of fertilizer applied and the yield produced (r2= 0.8228–0.9515). The best nutrient response was induced by hybrid PR37N01, while the weakest results were reached by hybrid PR37M81.
Abstract: Now a days, a significant part of commercial and governmental organisations like museums, cultural organizations, libraries, commercial enterprises, etc. invest intensively in new technologies for image digitization, digital libraries, image archiving and retrieval. Hence image authorization, authentication and security has become prime need. In this paper, we present a semi-fragile watermarking scheme for color images. The method converts the host image into YIQ color space followed by application of orthogonal dual domains of DCT and DWT transforms. The DCT helps to separate relevant from irrelevant image content to generate silent image features. DWT has excellent spatial localisation to help aid in spatial tamper characterisation. Thus image adaptive watermark is generated based of image features which allows the sharp detection of microscopic changes to locate modifications in the image. Further, the scheme utilises the multipurpose watermark consisting of soft authenticator watermark and chrominance watermark. Which has been proved fragile to some predefined processing like intentinal fabrication of the image or forgery and robust to other incidental attacks caused in the communication channel.
Abstract: the reliability analysis of the medical equipments can
help to increase the availability and the efficiency of the systems. In
this manuscript we present a simple method of decomposition that
could be easily applied on the complex medical systems. Using this
method we can easily calculate the effect of the subsystems or
components on the reliability of the overall system. Furthermore, to
investigate the effect of subsystems or components on system
performance, we perform a numerical study varying every time the
worst reliability of subsystem or component with another which has
higher reliability. It can also be useful to engineers and designers of
medical equipment, who wishes to optimize the complex systems.
Abstract: Economic freedoms, most emphasized issue in the recent years, are considered to affect economic growth and performance via institutional structure. In this context, a model that includes Turkey and Middle East Countries, and where the effects of economic freedom on growth are examined, was formed. For the groups of countries determined, in the study carried out by using the dataset belonging the period of 2004 - 2009, between economic freedoms and growth, a negative relationship was observed as group. In the sense of individual effects, it was identified that there was a positive relationship in terms of some Middle East Countries and Turkey.
Abstract: The aim of this study was to establish the relationship between the principles of Educational Sport and the objectives of Physical Education in two brasilian laws: National Curriculum Guidelines (PCNs) for the Elementary and Middle School Levels and the Guidelines and Basis Legislation (LDB). The method used was the survey analysis in order to determine the practices present in, or the opinions of, a specific population. The instrument used in this research was a questionnaire. After a broad review of the bibliography and according to the methodological procedures, the aim was to set the relationships between the Principles of Educational Sport and the objectives of Physical Education, according to the Brazilian Law (LDB) and National Curriculum Guidelines (PCNs) in a table made under the analysis of a group of specialists. As the relation between the principles of Educational Sport and the objectives of School Physical Education have shown, we can state that School Physical Education has gained pedagogical security for the potential use of Educational Sport as part of its contents.
Abstract: Noble metal participation in nanostructured
semiconductor catalysts has drawn much interest because of their
improved properties. Recently, it has been discussed by many
researchers that Ag participation in TiO2, CuO, ZnO semiconductors
showed improved photocatalytic and optical properties. In this
research, Ag/ZnO nanocomposite particles were prepared by
Ultrasonic Spray Pyrolysis(USP) Method. 0.1M silver and zinc
nitrate aqueous solutions were used as precursor solutions. The
Ag:Zn atomic ratio of the solution was selected 1:1. Experiments
were taken place under constant air flow of 400 mL/min at 800°C
furnace temperature. Particles were characterized by X-Ray
Diffraction (XRD), Scanning Electron Microscope (SEM) and
Energy Dispersive Spectroscopy (EDS). The crystallite sizes of Ag
and ZnO in composite particles are 24.6 nm, 19.7 nm respectively.
Although, spherical nanocomposite particles are in a range of 300-
800 nm, these particles are formed by the aggregation of primary
particles which are in a range of 20-60 nm.
Abstract: The paper deals with hydrodynamics of liquid-gas
layers under gas streaming through liquid layer on perforated plates
in column apparatuses. The plates with large apertures have been
investigated especially. It was shown that hydrodynamic regularities
for these plates are essentially different from known laws for foam
forming on fine-perforated plates. Main regularities of liquid-gas
interaction on plates with large apertures have been established.
Abstract: Researchers have been applying artificial/ computational intelligence (AI/CI) methods to computer games. In this research field, further researchesare required to compare AI/CI methods with respect to each game application. In thispaper, we report our experimental result on the comparison of evolution strategy, genetic algorithm and their hybrids, applied to evolving controller agents for MarioAI. GA revealed its advantage in our experiment, whereas the expected ability of ES in exploiting (fine-tuning) solutions was not clearly observed. The blend crossover operator and the mutation operator of GA might contribute well to explore the vast search space.
Abstract: This paper deals with the application of a fuzzy set in
measuring teachers- beliefs about mathematics. The vagueness of
beliefs was transformed into standard mathematical values using a
fuzzy preferences model. The study employed a fuzzy approach
questionnaire which consists of six attributes for measuring
mathematics teachers- beliefs about mathematics. The fuzzy conjoint
analysis approach based on fuzzy set theory was used to analyze the
data from twenty three mathematics teachers from four secondary
schools in Terengganu, Malaysia. Teachers- beliefs were recorded in
form of degrees of similarity and its levels of agreement. The
attribute 'Drills and practice is one of the best ways of learning
mathematics' scored the highest degree of similarity at 0. 79860 with
level of 'strongly agree'. The results showed that the teachers- beliefs
about mathematics were varied. This is shown by different levels of
agreement and degrees of similarity of the measured attributes.
Abstract: Several numerical schemes utilizing central difference
approximations have been developed to solve the Goursat problem.
However, in a recent years compact discretization methods which
leads to high-order finite difference schemes have been used since it
is capable of achieving better accuracy as well as preserving certain
features of the equation e.g. linearity. The basic idea of the new
scheme is to find the compact approximations to the derivative terms
by differentiating centrally the governing equations. Our primary
interest is to study the performance of the new scheme when applied
to two Goursat partial differential equations against the traditional
finite difference scheme.
Abstract: International competitiveness receives much attention
nowadays, but up to now its assessment has been heavily based on
manufacturing industry statistics. This paper addresses the need for
competitiveness indicators that cover the service sector and sets out a
multilevel framework for measuring international services trade
competitiveness. The approach undertaken here aims at
comparatively examining the international competitiveness of the
EU-25 (the twenty-five European Union member states before the 1st
of January 2007), Romanian and Bulgarian services trade, as well as
the last two countries- structure of specialization on the EU-25
services market. The primary changes in the international
competitiveness of three major services sectors – transportation,
travel and other services - are analyzed. This research attempts to
determine the ability of the two recent European Union (EU) member
states to contend with the challenges that might arise from the hard
competition within the enlarged EU, in the field of services trade.