Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: This paper presents a robust proportionalderivative
(PD) based cerebellar model articulation
controller (CMAC) for vertical take-off and landing flight
control systems. Successful on-line training and recalling
process of CMAC accompanying the PD controller is
developed. The advantage of the proposed method is mainly
the robust tracking performance against aerodynamic
parametric variation and external wind gust. The
effectiveness of the proposed algorithm is validated through
the application of a vertical takeoff and landing aircraft
control system.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: Calcium [Ca2+] dynamics is studied as a potential form
of neuron excitability that can control many irregular processes like
metabolism, secretion etc. Ca2+ ion enters presynaptic terminal and
increases the synaptic strength and thus triggers the neurotransmitter
release. The modeling and analysis of calcium dynamics in neuron
cell becomes necessary for deeper understanding of the processes
involved. A mathematical model has been developed for cylindrical
shaped neuron cell by incorporating physiological parameters like
buffer, diffusion coefficient, and association rate. Appropriate initial
and boundary conditions have been framed. The closed form solution
has been developed in terms of modified Bessel function. A computer
program has been developed in MATLAB 7.11 for the whole
approach.
Abstract: In this paper, the effect of transmission codes on the
performance of coherent square M-ary quadrature amplitude
modulation (CSMQAM) under hybrid selection/maximal-ratio
combining (H-S/MRC) diversity is analysed. The fading channels are
modeled as frequency non-selective slow independent and identically
distributed Rayleigh fading channels corrupted by additive white
Gaussian noise (AWGN). The results for coded MQAM are
computed numerically for the case of (24,12) extended Golay code
and compared with uncoded MQAM under H-S/MRC diversity by
plotting error probabilities versus average signal to noise ratio (SNR)
for various values L and N in order to examine the improvement in
the performance of the digital communications system as the number
of selected diversity branches is increased. The results for no
diversity, conventional SC and Lth order MRC schemes are also
plotted for comparison. Closed form analytical results derived in this
paper are sufficiently simple and therefore can be computed
numerically without any approximations. The analytical results
presented in this paper are expected to provide useful information
needed for design and analysis of digital communication systems
over wireless fading channels.
Abstract: In the past 20 years the economy of the Czech
Republic has experienced substantial changes. In the 1990s the
development was affected by the transformation which sought to
establish the right conditions for privatization and creation of
elementary market relations. In the last decade the characteristic
elements such as private ownership and corresponding institutional
framework have been strengthened. This development was marked by
the accession of the Czech Republic to the EU. The Czech Republic
is striving to reduce the difference between its level of economic
development and the quality of institutional framework in
comparison with other developed countries. The process of finding
the adequate solutions has been hampered by the negative impact of
the world financial crisis on the Czech Republic and the standard of
living of its inhabitants. This contribution seeks to address the
question of whether and to which extent the economic development
of the transitive Czech economy is affected by the change in
behaviour of households and their tendency to consumption, i.e. in
the sense of reduction or increase in demand for goods and services.
It aims to verify whether the increasing trend of household
indebtedness and decreasing trend of saving pose a significant risk in
the Czech Republic. At a general level the analysis aims to contribute
to finding an answer to the question of whether the debt increase of
Czech households is connected to the risk of "eating through" the
borrowed money and whether Czech households risk falling into a
debt trap. In addition to household indebtedness risks in the Czech
Republic the analysis will focus on identification of specifics of the
transformation phase of the Czech economy in comparison with the
EU countries, or selected OECD countries.
Abstract: The number of the companies accepting RFID in Korea
has been increased continuously due to the domestic development of
information technology. The acceptance of RFID by companies in
Korea enabled them to do business with many global enterprises in a
much more efficient and effective way. According to a survey[33,
p76], many companies in Korea have used RFID for inventory or
distribution manages. But, the use of RFID in the companies in Korea
is in the early stages and its potential value hasn-t fully been realized
yet. At this time, it would be very important to investigate the factors
that affect RFID acceptance. For this study, many previous studies
were referenced and some RFID experts were interviewed. Through
the pilot test, four factors were selected - Security Trust, Employee
Knowledge, Partner Influence, Service Provider Trust - affecting
RFID acceptance and an extended technology acceptance
model(e-TAM) was presented with those factors. The proposed model
was empirically tested using data collected from employees in
companies or public enterprises. In order to analyze some
relationships between exogenous variables and four variables in TAM,
structural equation modeling(SEM) was developed and SPSS12.0 and
AMOS 7.0 were used for analyses. The results are summarized as
follows: 1) security trust perceived by employees positively
influences on perceived usefulness and perceived ease of use; 2)
employee-s knowledge on RFID positively influences on only
perceived ease of use; 3) a partner-s influence for RFID acceptance
positively influences on only perceived usefulness; 4) service provider
trust very positively influences on perceived usefulness and perceived
ease of use 5) the relationships between TAM variables are the same as
the previous studies.
Abstract: This paper presents a cold chain monitoring system which focuses on assessment of quality and dynamic pricing information about food in cold chain. Cold chain is composed of many actors and stages; however it can be seen as a single entity since a breakdown in temperature control at any stage can impact the final quality of the product. In a cold chain, the shelf life, quality, and safety of perishable food throughout the supply chain is greatly impacted by environmental factors especially temperature. In this paper, a prototype application is implemented to retrieve timetemperature history, the current quality and the dynamic price setting according to changing quality impacted by temperature fluctuations in real-time.
Abstract: Bentonitic material from South Aswan, Egypt was evaluated in terms of mineral-ogy and chemical composition as bleaching clay in refining of transformer oil before and after acid activation and thermal treatment followed by acid leaching using HCl and H2SO4 for different contact times. Structural modification and refining power of bento-nite were investigated during modification by means of X-ray diffraction and infrared spectroscopy. The results revealed that the activated bentonite could be used for refining of transformer oil. The oil parameters such as; dielectric strength, viscosity and flash point had been improved. The dielectric breakdown strength of used oil increased from 29 kV for used oil treated with unactivated bentonite to 74 kV after treatment with activated bentonite. Kinematic Viscosity changed from 19 to 11 mm2 /s after treatment with activated bentonite. However, flash point achieved 149 ºC.
Abstract: Work-life balance has been acknowledged and
promoted for the sake of employee retention. It is essential for a
manager to realize the human resources situation within a company to
help employees work happily and perform at their best. This paper
suggests knowledge management and critical thinking are useful to
motivate employees to think about their work-life balance. A
qualitative case study is presented, which aimed to discover the
meaning of work-life balance-s meaning from the perspective of Thai
knowledge workers and how it affects their decision-making towards
work resignation. Results found three types of work-life balance
dimensions; a work- life balance including a workplace and a private
life setting, an organizational working life balance only, and a worklife
balance only in a private life setting. These aspects all influenced
the decision-making of the employees. Factors within a theme of an
organizational work-life balance were involved with systematic
administration, fair treatment, employee recognition, challenging
assignments to gain working experience, assignment engagement,
teamwork, relationship with superiors, and working environment,
while factors concerning private life settings were about personal
demands such as an increasing their salary or starting their own
business.
Abstract: In this contribution, a way to enhance the performance of the classic Genetic Algorithm is proposed. The idea of restarting a Genetic Algorithm is applied in order to obtain better knowledge of the solution space of the problem. A new operator of 'insertion' is introduced so as to exploit (utilize) the information that has already been collected before the restarting procedure. Finally, numerical experiments comparing the performance of the classic Genetic Algorithm and the Genetic Algorithm with restartings, for some well known test functions, are given.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: The purpose of this study is to derive optimal shapes of
a body located in viscous flows by the finite element method using the
acoustic velocity and the four-step explicit scheme. The formulation
is based on an optimal control theory in which a performance function
of the fluid force is introduced. The performance function should be
minimized satisfying the state equation. This problem can be transformed
into the minimization problem without constraint conditions
by using the adjoint equation with adjoint variables corresponding to
the state equation. The performance function is defined by the drag
and lift forces acting on the body. The weighted gradient method
is applied as a minimization technique, the Galerkin finite element
method is used as a spatial discretization and the four-step explicit
scheme is used as a temporal discretization to solve the state equation
and the adjoint equation. As the interpolation, the orthogonal basis
bubble function for velocity and the linear function for pressure
are employed. In case that the orthogonal basis bubble function is
used, the mass matrix can be diagonalized without any artificial
centralization. The shape optimization is performed by the presented
method.
Abstract: The aim of this study was to examine the dynamics of functional composition of a non flooded Amazonian forest in response to drought stress in terms of diameter growth, recruitment and mortality. The survey was carried out in the continuous forest of the Biological dynamics of forest fragments project 90 km outside the city of Manaus, state of Amazonas Brazil. All stems >10 cm dbh where identified to species level and monitored in 18 one hectare permanent sample plots from 1981 to 2004.For statistical analysis all species where aggregated in three ecological guilds. Two distinct drought events occurred in 1983 and 1997. Results showed that more early successional species performed better than later successional ones. Response was significant for both events but for the 1997 event this was more pronounced possibly because of the fact that the event was in the middle of the dry rather than the wet period as was the 1983 one.
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: Permeability reduction induced by asphaltene
precipitation during gas injection is one of the serious problems in
the oil industry. This problem can lead to formation damage and
decrease the oil production rate. In this work, Malaysian light oil
sample has been used to investigate the effect CO2 injection and
Water Alternating Gas (WAG) injection on permeability reduction.
In this work, dynamic core flooding experiments were conducted to
study the effect of CO2 and WAG injection on the amount of
asphaltene precipitated. Core properties after displacement were
inspected for any permeability reduction to study the effect of
asphaltene precipitation on rock properties.
The results showed that WAG injection gave less asphaltene
precipitation and formation damage compared to CO2 injection. The
study suggested that WAG injection can be one of the important
factors of managing asphaltene precipitation.
Abstract: Recent research on seeds of bio-diesel plants like
Jatropha curcas, constituting 40-50% bio-crude oil indicates its
potential as one of the most promising alternatives to conventional
sources of energy. Also, limited studies on utilization of de-oiled cake
have revealed that Jatropha bio-waste has good potential to be used as
organic fertilizers produced via aerobic and anaerobic treatment.
However, their commercial exploitation has not yet been possible. The
present study aims at developing appropriate bio-processes and
formulations utilizing Jatropha seed cake as organic fertilizer, for
improving the growth of Polianthes tuberose L. (Tuberose). Pot
experiments were carried out by growing tuberose plants on soil
treated with composted formulations of Jatropha de-oiled cake, Farm
Yard Manure (FYM) and inorganic fertilizers were also blended in
soil. The treatment was carried out through soil amendment as well as
foliar spray. The growth and morphological parameters were
monitored for entire crop cycle.
The growth Length and number of leaves, spike length, rachis
length, number of bulb per plant and earliness of sprouting of bulb and
yield enhancement were comparable to that achieved under inorganic
fertilizer. Furthermore, performance of inorganic fertilizer also showed
an improvement when blended with composted bio-waste. These
findings would open new avenues for Jatropha based bio-wastes to be
composted and used as organic fertilizers for commercial floriculture.
Abstract: Cosmic showers, from their places of origin in space,
after entering earth generate secondary particles called Extensive Air
Shower (EAS). Detection and analysis of EAS and similar High
Energy Particle Showers involve a plethora of experimental setups
with certain constraints for which soft-computational tools like
Artificial Neural Network (ANN)s can be adopted. The optimality
of ANN classifiers can be enhanced further by the use of Multiple
Classifier System (MCS) and certain data - dimension reduction
techniques. This work describes the performance of certain data
dimension reduction techniques like Principal Component Analysis
(PCA), Independent Component Analysis (ICA) and Self Organizing
Map (SOM) approximators for application with an MCS formed
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN). The data inputs are
obtained from an array of detectors placed in a circular arrangement
resembling a practical detector grid which have a higher dimension
and greater correlation among themselves. The PCA, ICA and SOM
blocks reduce the correlation and generate a form suitable for real
time practical applications for prediction of primary energy and
location of EAS from density values captured using detectors in a
circular grid.
Abstract: Nowadays, ontologies are the only widely accepted paradigm for the management of sharable and reusable knowledge in a way that allows its automatic interpretation. They are collaboratively created across the Web and used to index, search and annotate documents. The vast majority of the ontology based approaches, however, focus on indexing texts at document level. Recently, with the advances in ontological engineering, it became clear that information indexing can largely benefit from the use of general purpose ontologies which aid the indexing of documents at word level. This paper presents a concept indexing algorithm, which adds ontology information to words and phrases and allows full text to be searched, browsed and analyzed at different levels of abstraction. This algorithm uses a general purpose ontology, OntoRo, and an ontologically tagged corpus, OntoCorp, both developed for the purpose of this research. OntoRo and OntoCorp are used in a two-stage supervised machine learning process aimed at generating ontology tagging rules. The first experimental tests show a tagging accuracy of 78.91% which is encouraging in terms of the further improvement of the algorithm.
Abstract: One of the robust fault detection filter (RFDF)
designing method is based on sliding-mode theory. The main purpose
of our study is to introduce an innovative simplified reference
residual model generator to formulate the RFDF as a sliding-mode
observer without any manipulation package or transformation matrix,
through which the generated residual signals can be evaluated. So the
proposed design is more explicit and requires less design parameters
in comparison with approaches requiring changing coordinates. To
the best author's knowledge, this is the first time that the sliding
mode technique is applied to detect actuator and sensor faults in a
real boiler. The designing procedure is proposed in a drum boiler in
Synvendska Kraft AB Plant in Malmo, Sweden as a multivariable
and strongly coupled system. It is demonstrated that both sensor and
actuator faults can robustly be detected. Also sensor faults can be
diagnosed and isolated through this method.