Abstract: The building sector is the largest energy consumer and
CO2 emitter in the European Union (EU) and therefore the active
reduction of energy consumption and elimination of energy wastage
are among the main goals in it. Healthy housing and energy
efficiency are affected by many factors which set challenges to
monitoring, control and research of indoor air quality (IAQ) and
energy consumption, especially in old buildings. These challenges
include measurement and equipment costs, for example.
Additionally, the measurement results are difficult to interpret and
their usage in the ventilation control is also limited when taking into
account the energy efficiency of housing at the same time. The main
goal of this study is to develop a cost-effective building monitoring
and control system especially for old buildings. The starting point or
keyword of the development process is a wireless system; otherwise
the installation costs become too high. As the main result, this paper
describes an idea of a wireless building monitoring and control
system. The first prototype of the system has been installed in 10
residential buildings and in 10 school buildings located in the City of
Kuopio, Finland.
Abstract: In this paper, a new approach for design of a fully
differential second order current mode continuous-time sigma-delta
modulator is presented. For circuit implementation, square root
domain (SRD) translinear loop based on floating-gate MOS
transistors that operate in saturation region is employed. The
modulator features, low supply voltage, low power consumption
(8mW) and high dynamic range (55dB). Simulation results confirm
that this design is suitable for data converters.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: This paper presents a watermarking protocol able to
solve the well-known “customer-s right problem" and “unbinding
problem". In particular, the protocol has been purposely designed
to be adopted in a web context, where users wanting to buy digital
contents are usually neither provided with digital certificates issued
by certification authorities (CAs) nor able to autonomously perform
specific security actions. Furthermore, the protocol enables users to
keep their identities unexposed during web transactions as well as
allows guilty buyers, i.e. who are responsible distributors of illegal
replicas, to be unambiguously identified. Finally, the protocol has
been designed so that web content providers (CPs) can exploit
copyright protection services supplied by web service providers (SPs)
in a security context. Thus, CPs can take advantage of complex
services without having to directly implement them.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: This research is a collaborative narrative research, which is mixed with issues of selected papers and researcher's experience as an anonymous user on social networking sites. The objective of this research is to understand the reasons of the regular users who reject to contact with anonymous users, and to study the communication traditions used in the selected studies. Anonymous users are rejected by regular users, because of the fear of cyber bully, the fear of unpleasant behaviors, and unwillingness of changing communication norm. The suggestion for future research design is to use longitudinal design or quantitative design; and the theory in rhetorical tradition should be able to help develop a strong trust message.
Abstract: A methodology to design a nonlinear observer in a
bond graph approach is proposed. The class of nonlinear observer
with multivariable nonlinearities is considered. A junction structure
of the bond graph observer is proposed. The proposed methodology
to an electrical transformer and a DC motor including the nonlinear
saturation is applied. Nonlinear observers for the transformer and DC
motor based on multivariable circle criterion in the physical domain
are proposed. In order to show the saturation effects on the
transformer and DC motor, simulation results are obtained. Finally,
the paper describes that convergence of the estimates to the true
states is achieved.
Abstract: Dorsal hand vein pattern is an emerging biometric which is attracting the attention of researchers, of late. Research is being carried out on existing techniques in the hope of improving them or finding more efficient ones. In this work, Principle Component Analysis (PCA) , which is a successful method, originally applied on face biometric is being modified using Cholesky decomposition and Lanczos algorithm to extract the dorsal hand vein features. This modified technique decreases the number of computation and hence decreases the processing time. The eigenveins were successfully computed and projected onto the vein space. The system was tested on a database of 200 images and using a threshold value of 0.9 to obtain the False Acceptance Rate (FAR) and False Rejection Rate (FRR). This modified algorithm is desirable when developing biometric security system since it significantly decreases the matching time.
Abstract: Dispersions of casein micelles (CM) were studied at a
constant protein concentration of 5 wt % in high NaCl environment
ranging from 0% to 12% by Dynamic light scattering (DLS) and
Fourier Transform Infrared (FTIR). The rehydration profiles obtained
were interpreted in term of wetting, swelling and dispersion stages by
using a turbidity method. Two behaviours were observed depending
on the salt concentration. The first behaviour (low salt concentration)
presents a typical rehydration profile with a significant change
between 3 and 6% NaCl indicating quick wetting, swelling and long
dispersion stage. On the opposite, the dispersion stage of the second
behaviour (high salt concentration) was significantly shortened
indicating a strong modification of the protein backbone. A salt
increase result to a destabilization of the micelle and the formation of
mini-micelles more or less aggregated indicating an average micelles
size ranging from 100 to 200 nm. For the first time, the estimations
of secondary structural elements (irregular, ß-sheet, α-helix and turn)
by the Amide III assignments were correlated with results from
Amide I.
Abstract: This paper presents preliminary results regarding system-level power awareness for FPGA implementations in wireless sensor networks. Re-configurability of field programmable gate arrays (FPGA) allows for significant flexibility in its applications to embedded systems. However, high power consumption in FPGA becomes a significant factor in design considerations. We present several ideas and their experimental verifications on how to optimize power consumption at high level of designing process while maintaining the same energy per operation (low-level methods can be used additionally). This paper demonstrates that it is possible to estimate feasible power consumption savings even at the high level of designing process. It is envisaged that our results can be also applied to other embedded systems applications, not limited to FPGA-based.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: The modeling of inelastic behavior of plastic materials requires measurements providing information on material response to different multiaxial loading conditions. Different triaxiality conditions and values of Lode parameters have to be
covered for complex description of the material plastic behavior.
Samples geometries providing material plastic behavoiur over the range of interest are proposed with the use of FEM analysis. Round samples with 3 different notches and smooth surface are used
together with butterfly type of samples tested at angle ranging for 0 to
90°. Identification of ductile damage parameters is carried out on
the basis of obtained experimental data for austenitic stainless steel.
The obtained material plastic damage parameters are subsequently applied to FEM simulation of notched CT normally samples used for
fracture mechanics testing and results from the simulation are
compared with real tests.
Abstract: In order to alleviate the mental and physical problems
of persons with disabilities, animal-assisted therapy (AAT) is one of
the possible modalities that employs the merit of the human-animal
interaction. Nevertheless, to achieve the purpose of AAT for persons
with severe disabilities (e.g. spinal cord injury, stroke, and
amyotrophic lateral sclerosis), real-time animal language
interpretation is desirable. Since canine behaviors can be visually
notable from its tail, this paper proposes the automatic real-time
interpretation of canine tail language for human-canine interaction in
the case of persons with severe disabilities. Canine tail language is
captured via two 3-axis accelerometers. Directions and frequencies
are selected as our features of interests. The novel fuzzy rules based
on Gaussian-Trapezoidal model and center of gravity (COG)-based
defuzzification method are proposed in order to interpret the features
into four canine emotional behaviors, i.e., agitate, happy, scare and
neutral as well as its blended emotional behaviors. The emotional
behavior model is performed in the simulated dog and has also been
evaluated in the real dog with the perfect recognition rate.
Abstract: In this paper, a Markovian risk model with two-type claims is considered. In such a risk model, the occurrences of the two type claims are described by two point processes {Ni(t), t ¸ 0}, i = 1, 2, where {Ni(t), t ¸ 0} is the number of jumps during the interval (0, t] for the Markov jump process {Xi(t), t ¸ 0} . The ruin probability ª(u) of a company facing such a risk model is mainly discussed. An integral equation satisfied by the ruin probability ª(u) is obtained and the bounds for the convergence rate of the ruin probability ª(u) are given by using key-renewal theorem.
Abstract: The energy consumption and delay in read/write
operation of conventional SRAM is investigated analytically as well
as by simulation. Explicit analytical expressions for the energy
consumption and delay in read and write operation as a function of
device parameters and supply voltage are derived. The expressions are
useful in predicting the effect of parameter changes on the energy
consumption and speed as well as in optimizing the design of
conventional SRAM. HSPICE simulation in standard 0.25μm CMOS
technology confirms precision of analytical expressions derived from
this paper.
Abstract: Detection of squirrel cage induction motor (SCIM) broken bars has long been an important but difficult job in the detection area of motor faults. Early detection of this abnormality in the motor would help to avoid costly breakdowns. A new detection method based on particle swarm optimization (PSO) is presented in this paper. Stator current in an induction motor will be measured and characteristic frequency components of faylted rotor will be detected by minimizing a fitness function using pso. Supply frequency and side band frequencies and their amplitudes can be estimated by the proposed method. The proposed method is applied to a faulty motor with one and two broken bars in different loading condition. Experimental results prove that the proposed method is effective and applicable.
Abstract: Nowadays, hand vein recognition has attracted more attentions in identification biometrics systems. Generally, hand vein image is acquired with low contrast and irregular illumination. Accordingly, if you have a good preprocessing of hand vein image, we can easy extracted the feature extraction even with simple binarization. In this paper, a proposed approach is processed to improve the quality of hand vein image. First, a brief survey on existing methods of enhancement is investigated. Then a Radon Like features method is applied to preprocessing hand vein image. Finally, experiments results show that the proposed method give the better effective and reliable in improving hand vein images.
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: We study the typical domain size and configuration
character of a randomly perturbed system exhibiting continuous
symmetry breaking. As a model system we use rod-like objects
within a cubic lattice interacting via a Lebwohl–Lasher-type
interaction. We describe their local direction with a headless unit
director field. An example of such systems represents nematic LC or
nanotubes. We further introduce impurities of concentration p, which
impose the random anisotropy field-type disorder to directors. We
study the domain-type pattern of molecules as a function of p,
anchoring strength w between a neighboring director and impurity,
temperature, history of samples. In simulations we quenched the
directors either from the random or homogeneous initial
configuration. Our results show that a history of system strongly
influences: i) the average domain coherence length; and ii) the range
of ordering in the system. In the random case the obtained order is
always short ranged (SR). On the contrary, in the homogeneous case,
SR is obtained only for strong enough anchoring and large enough
concentration p. In other cases, the ordering is either of quasi long
range (QLR) or of long range (LR). We further studied memory
effects for the random initial configuration. With increasing external
ordering field B either QLR or LR is realized.
Abstract: The flow field and the motion of the free surface in an
oscillating container are simulated numerically to assess the numerical
approach for studying two-phase flows under oscillating conditions.
Two numerical methods are compared: one is to model the oscillating
container directly using the moving grid of the ALE method, and the
other is to simulate the effect of container motion using the oscillating
body force acting on the fluid in the stationary container. The
two-phase flow field in the container is simulated using the level set
method in both cases. It is found that the calculated results by the body
force method coinsides with those by the moving grid method and the
sloshing behavior is predicted well by both the methods. Theoretical
back ground and limitation of the body force method are discussed,
and the effects of oscillation amplitude and frequency are shown.