Abstract: This paper presents an adaptive technique for generation
of data required for construction of artificial neural network-based
performance model of nano-scale CMOS inverter circuit. The training
data are generated from the samples through SPICE simulation. The
proposed algorithm has been compared to standard progressive sampling
algorithms like arithmetic sampling and geometric sampling.
The advantages of the present approach over the others have been
demonstrated. The ANN predicted results have been compared with
actual SPICE results. A very good accuracy has been obtained.
Abstract: The calculation of buckling length factor (K) for steel
frames columns is a major and governing processes to determine the
dimensions steel frame columns cross sections during design. The
buckling length of steel frames columns has a direct effect on the cost
(weight) of using cross section. A new formula is required to
determine buckling length factor (K) by simplified way. In this
research a new formula for buckling length factor (K) was established
to determine by accurate method for a limited interval of columns
ends rigidity (GA, GB). The new formula can be used ease to
evaluate the buckling length factor without needing to complicated
equations or difficult charts.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: In production planning (PP) periods with excess capacity
and growing demand, the manufacturers have two options to use the excess capacity. First, it could do more changeovers and thus reduce lot sizes, inventories, and inventory costs. Second, it could produce in excess of demand in the period and build additional inventory that can be used to satisfy future demand increments, thus
delaying the purchase of the next machine that is required to meet the growth in demand. In this study we propose an enhanced supply
chain planning model with flexible planning capability. In addition, a 3D supply chain planning system is illustrated.
Abstract: There are three main ways of categorizing capital in banking operations: accounting, regulatory and economic capital. However, the 2008-2009 global crisis has shown that none of these categories adequately reflects the real risks of bank operations, especially in light of the failures Bear Stearns, Lehman Brothers or Northern Rock. This paper deals with the economic capital allocation of global banks. In theory, economic capital should reflect the real risks of a bank and should be publicly available. Yet, as discovered during the global financial crisis, even when economic capital information was publicly disclosed, the underlying assumptions rendered the information useless. Specifically, some global banks that reported relatively high levels of economic capital before the crisis went bankrupt or had to be bailed-out by their government. And, only 15 out of 50 global banks reported their economic capital during the 2007-2010 period. In this paper, we analyze the changes in reported bank economic capital disclosure during this period. We conclude that relative shares of credit and business risks increased in 2010 compared to 2007, while both operational and market risks decreased their shares on the total economic capital of top-rated global banks. Generally speaking, higher levels of disclosure and transparency of bank operations are required to obtain more confidence from stakeholders. Moreover, additional risks such as liquidity risks should be included in these disclosures.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: Producing IT products/services required carefully
designed. IT development process is intangible and labour intensive.
Making optimal use of available resources, both soft (knowledge,
skill-set etc.) and hard (computer system, ancillary equipment etc.),
is vital if IT development is to achieve sensible economical
advantages. Apart from the norm of Project Life Cycle and System
Development Life Cycle (SDLC), there is an urgent need to establish
a general yet widely acceptable guideline on the most effective and
efficient way to precede an IT project in the broader view of Product
Life Cycle. The current paper proposes such a framework with two
major areas of concern: (1) an integration of IT Products and IT
Services within an existing IT Process architecture and; (2) how IT
Product and IT Services are built into the framework of Product Life
Cycle, Project Life Cycle and SDLC.
Abstract: To determine the presence and location of faults in a transmission by the adaptation of protective distance relay based on the measurement of fixed settings as line impedance is achieved by several different techniques. Moreover, a fast, accurate and robust technique for real-time purposes is required for the modern power systems. The appliance of radial basis function neural network in transmission line protection is demonstrated in this paper. The method applies the power system via voltage and current signals to learn the hidden relationship presented in the input patterns. It is experiential that the proposed technique is competent to identify the particular fault direction more speedily. System simulations studied show that the proposed approach is able to distinguish the direction of a fault on a transmission line swiftly and correctly, therefore suitable for the real-time purposes.
Abstract: This paper determines most common model of in-pipe
robots to derive its degree of freedom in order to compare with the
necessary degree of freedom required for a system to move inside
pipelines freely in order to derive analytical reason for losing control
of in-pipe robots at branched pipe. DOF of most common mechanism
in in-pipe robots can be calculated by considering the robot as a
parallel manipulator. A new design based on previously researched
in-pipe robot PAROYS has been suggested, and its possibility to
overcome branched section has been simulated.
Abstract: This paper will provide the kinematic and dynamic
analysis of a lower limb exoskeleton. The forward and inverse
kinematics of proposed exoskeleton is performed using Denevit and
Hartenberg method. The torques required for the actuators will be
calculated using Lagrangian formulation technique. This research can
be used to design the control of the proposed exoskeleton.
Abstract: Dredging activities inevitably cause sediment
dispersion. In certain locations, where there are important ecological
areas such as mangroves or coral reefs, carefully planning the
dredging can significantly reduce negative impacts. This article
utilizes the dredging at Phuket port, Thailand, as a case study to
demonstrate how computer simulations can be helpful to protect
existing coral reefs. A software package named MIKE21 was
applied. Necessary information required by the simulations was
gathered. After calibrating and verifying the model, various dredging
scenario were simulated to predict spoil movement. The simulation
results were used as guidance to setting up an environmental
measure. Finally, the recommendation to dredge during flood tide
with silt curtains installed was made.
Abstract: It was determined that woody biomass and livestock excreta can be utilized as hydrogen resources and hydrogen produced from such sources can be used to fill fuel cell vehicles (FCVs) at hydrogen stations. It was shown that the biomass transport costs for hydrogen production may be reduced the costs for co-generation. In the Tokyo Metropolitan Area, there are only a few sites capable of producing hydrogen from woody biomass in amounts greater than 200 m3/h-the scale required for a hydrogen station to be operationally practical. However, in the case of livestock excreta, it was shown that 15% of the municipalities in this area are capable of securing sufficient biomass to be operationally practical for hydrogen production. The differences in feasibility of practical operation depend on the type of biomass.
Abstract: Under the limitation of investment budget, a utility
company is required to maximize the utilization of their existing
assets during their life cycle satisfying both engineering and financial
requirements. However, utility does not have knowledge about the
status of each asset in the portfolio neither in terms of technical nor
financial values. This paper presents a knowledge based model for
the utility companies in order to make an optimal decision on power
transformer with their utilization. CommonKADS methodology, a
structured development for knowledge and expertise representation,
is utilized for designing and developing knowledge based model. A
case study of One MVA power transformer of Nepal Electricity
Authority is presented. The results show that the reusable knowledge
can be categorized, modeled and utilized within the utility company
using the proposed methodologies. Moreover, the results depict that
utility company can achieve both engineering and financial benefits
from its utilization.
Abstract: The upgrading of low quality crude natural gas (NG) is attracting interest due to high demand of pipeline-grade gas in recent years. Membrane processes are commercially proven technology for the removal of impurities like carbon dioxide from NG. In this work, cross flow mathematical model has been suggested to be incorporated with ASPEN HYSYS as a user defined unit operation in order to design the membrane system for CO2/CH4 separation. The effect of operating conditions (such as feed composition and pressure) and membrane selectivity on the design parameters (methane recovery and total membrane area required for the separation) has been studied for different design configurations. These configurations include single stage (with and without recycle) and double stage membrane systems (with and without permeate or retentate recycle). It is shown that methane recovery can be improved by recycling permeate or retentate stream as well as by using double stage membrane systems. The ASPEN HYSYS user defined unit operation proposed in the study has potential to be applied for complex membrane system design and optimization.
Abstract: In this paper the problem of face recognition under variable illumination conditions is considered. Most of the works in the literature exhibit good performance under strictly controlled acquisition conditions, but the performance drastically drop when changes in pose and illumination occur, so that recently number of approaches have been proposed to deal with such variability. The aim of this work is to introduce an efficient local appearance feature extraction method based steerable pyramid (SP) for face recognition. Local information is extracted from SP sub-bands using LBP(Local binary Pattern). The underlying statistics allow us to reduce the required amount of data to be stored. The experiments carried out on different face databases confirm the effectiveness of the proposed approach.
Abstract: Vehicular Ad-Hoc Networks (VANET) can provide
communications between vehicles or infrastructures. It provides the
convenience of driving and the secure driving to reduce accidents. In
VANET, the security is more important because it is closely related to
accidents. Additionally, VANET raises a privacy issue because it can
track the location of vehicles and users- identity when a security
mechanism is provided. In this paper, we analyze the problem of an
existing solution for security requirements required in VANET, and
resolve the problem of the existing method when a key management
mechanism is provided for the security operation in VANET.
Therefore, we show suitability of the Long Term Evolution (LTE) in
VANET for the solution of this problem.
Abstract: This study investigates CO2 mitigation by methanol
synthesis from flue gas CO2 and H2 generation through water
electrolysis. Electrolytic hydrogen generation is viable provided that
the required electrical power is supplied from renewable energy
resources; whereby power generation from renewable resources is yet
commercial challenging. This approach contribute to zero-emission,
moreover it produce oxygen which could be used as feedstock for
chemical process. At ZPC, however, oxygen would be utilized
through partial oxidation of methane in autothermal reactor (ATR);
this makes ease the difficulties of O2 delivery and marketing. On the
other hand, onboard hydrogen storage and consumption; in methanol
plant; make the project economically more competitive.