Abstract: This paper presents a 24 watts SEPIC converter design
and control using microprocessor. SEPIC converter has advantages of
a wide input range and miniaturization caused by the low stress at
elements. There is also an advantage that the input and output are
isolated in MOSFET-off state. This paper presents the PID control
through the SEPIC converter transfer function using a DSP and the
protective circuit for fuel cell from the over-current and
inverse-voltage by using the characteristic of SEPIC converter. Then it
derives them through the experiments.
Abstract: This paper presents the adaptive control scheme
with sliding mode compensator for vibration control problem
in the presence of disturbance. The dynamic model of the
flexible cantilever beam using finite element modeling is
derived. The adaptive control with sliding mode compensator
using output feedback for output tracking is developed to
reject the external disturbance, and to improve the tracking
performance. Satisfactory simulation results verify that the
effectiveness of adaptive control scheme with sliding mode
compensator.
Abstract: This paper presents a new high speed simulation methodology to solve the long simulation time problem of CMOS image sensor matrix. Generally, for integrating the pixel matrix in SOC and simulating the system performance, designers try to model the pixel in various modeling languages such as VHDL-AMS, SystemC or Matlab. We introduce a new alternative method based on spice model in cadence design platform to achieve accuracy and reduce simulation time. The simulation results indicate that the pixel output voltage maximum error is at 0.7812% and time consumption reduces from 2.2 days to 13 minutes achieving about 240X speed-up for the 256x256 pixel matrix.
Abstract: In this paper, many techniques for blind identification of moving average (MA) process are presented. These methods utilize third- and fourth-order cumulants of the noisy observations of the system output. The system is driven by an independent and identically distributed (i.i.d) non-Gaussian sequence that is not observed. Two nonlinear optimization algorithms, namely the Gradient Descent and the Gauss-Newton algorithms are exposed. An algorithm based on the joint-diagonalization of the fourth-order cumulant matrices (FOSI) is also considered, as well as an improved version of the classical C(q, 0, k) algorithm based on the choice of the Best 1-D Slice of fourth-order cumulants. To illustrate the effectiveness of our methods, various simulation examples are presented.
Abstract: Multi-level voltage source inverters offer several
advantages such as; derivation of a refined output voltage with
reduced total harmonic distortion (THD), reduction of voltage ratings
of the power semiconductor switching devices and also the reduced
electro-magnetic-interference problems etc. In this paper, new
carrier-overlapped phase-disposition or sub-harmonic sinusoidal
pulse width modulation (CO-PD-SPWM) and also the carrieroverlapped
phase-disposition space vector modulation (CO-PDSVPWM)
schemes for a six-level diode-clamped inverter topology
are proposed. The principle of the proposed PWM schemes is similar
to the conventional PD-PWM with a little deviation from it in the
sense that the triangular carriers are all overlapped. The overlapping
of the triangular carriers on one hand results in an increased number
of switchings, on the other hand this facilitates an improved spectral
performance of the output voltage. It is demonstrated through
simulation studies that the six-level diode-clamped inverter with the
use of CO-PD-SPWM and CO-PD-SVPWM proposed in this paper is
capable of generating multiple levels in its output voltage. The
advantages of the proposed PWM schemes can be derived to benefit,
especially at lower modulation indices of the inverter and hence this
aspect of the proposed PWM schemes can be well exploited in high
power applications requiring low speeds of operation of the drive.
Abstract: Induction motors are being used in greater numbers
throughout a wide variety of industrial and commercial applications
because it provides many benefits and reliable device to convert the
electrical energy into mechanical motion. In some application it-s
desired to control the speed of the induction motor. Because of the
physics of the induction motor the preferred method of controlling its
speed is to vary the frequency of the AC voltage driving the motor. In
recent years, with the microcontroller incorporated into an appliance
it becomes possible to use it to generate the variable frequency AC
voltage to control the speed of the induction motor.
This study investigates the microcontroller based variable
frequency power inverter. the microcontroller is provide the variable
frequency pulse width modulation (PWM) signal that control the
applied voltage on the gate drive, which is provides the required
PWM frequency with less harmonics at the output of the power
inverter.
The fully controlled bridge voltage source inverter has been
implemented with semiconductors power devices isolated gate
bipolar transistor (IGBT), and the PWM technique has been
employed in this inverter to supply the motor with AC voltage.
The proposed drive system for three & single phase power inverter
is simulated using Matlab/Simulink. The Matlab Simulation Results
for the proposed system were achieved with different SPWM. From
the result a stable variable frequency inverter over wide range has
been obtained and a good agreement has been found between the
simulation and hardware of a microcontroller based single phase
inverter.
Abstract: This article proposes a voltage-mode
multifunction filter using differential voltage current
controllable current conveyor transconductance amplifier
(DV-CCCCTA). The features of the circuit are that: the
quality factor and pole frequency can be tuned independently
via the values of capacitors: the circuit description is very
simple, consisting of merely 1 DV-CCCCTA, and 2
capacitors. Without any component matching conditions, the
proposed circuit is very appropriate to further develop into
an integrated circuit. Additionally, each function response
can be selected by suitably selecting input signals with
digital method. The PSpice simulation results are depicted.
The given results agree well with the theoretical anticipation.
Abstract: A new fuzzy filter is presented for noise reduction of
images corrupted with additive noise. The filter consists of two
stages. In the first stage, all the pixels of image are processed for
determining noisy pixels. For this, a fuzzy rule based system
associates a degree to each pixel. The degree of a pixel is a real
number in the range [0,1], which denotes a probability that the pixel
is not considered as a noisy pixel. In the second stage, another fuzzy
rule based system is employed. It uses the output of the previous
fuzzy system to perform fuzzy smoothing by weighting the
contributions of neighboring pixel values. Experimental results are
obtained to show the feasibility of the proposed filter. These results
are also compared to other filters by numerical measure and visual
inspection.
Abstract: Fuel cell's system requires regulating circuit for
voltage and current in order to control power in case of connecting to
other generative devices or load. In this paper Fuel cell system and
convertor, which is a multi-variable system, are controlled using
sliding mode method. Use of weighting matrix in design procedure
made it possible to regulate speed of control. Simulation results show
the robustness and accuracy of proposed controller for controlling
desired of outputs.
Abstract: An additive fuzzy system comprising m rules with
n inputs and p outputs in each rule has at least t m(2n + 2 p + 1)
parameters needing to be tuned. The system consists of a large
number of if-then fuzzy rules and takes a long time to tune its
parameters especially in the case of a large amount of training data
samples. In this paper, a new learning strategy is investigated to cope
with this obstacle. Parameters that tend toward constant values at the
learning process are initially fixed and they are not tuned till the end
of the learning time. Experiments based on applications of the
additive fuzzy system in function approximation demonstrate that the
proposed approach reduces the learning time and hence improves
convergence speed considerably.
Abstract: SDMA (Space-Division Multiple Access) is a MIMO
(Multiple-Input and Multiple-Output) based wireless communication
network architecture which has the potential to significantly increase
the spectral efficiency and the system performance. The maximum
likelihood (ML) detection provides the optimal performance, but its
complexity increases exponentially with the constellation size of
modulation and number of users. The QR decomposition (QRD)
MUD can be a substitute to ML detection due its low complexity and
near optimal performance. The minimum mean-squared-error
(MMSE) multiuser detection (MUD) minimises the mean square
error (MSE), which may not give guarantee that the BER of the
system is also minimum. But the minimum bit error rate (MBER)
MUD performs better than the classic MMSE MUD in term of
minimum probability of error by directly minimising the BER cost
function. Also the MBER MUD is able to support more users than
the number of receiving antennas, whereas the rest of MUDs fail in
this scenario. In this paper the performance of various MUD
techniques is verified for the correlated MIMO channel models based
on IEEE 802.16n standard.
Abstract: An approach and its implementation in 0.18 m CMOS process of the multichannel ASIC for capacitive (up to 30 pF) sensors are described in the paper. The main design aim was to study an analog data-driven architecture. The design was done for an analog derandomizing function of the 128 to 16 structure. That means that the ASIC structure should provide a parallel front-end readout of 128 input analog sensor signals and after the corresponding fast commutation with appropriate arbitration logic their processing by means of 16 output chains, including analog-to-digital conversion. The principal feature of the ASIC is a low power consumption within 2 mW/channel (including a 9-bit 20Ms/s ADC) at a maximum average channel hit rate not less than 150 kHz.
Abstract: This paper presents the design and analysis of a parallel
connected inverter configuration of. The configuration consists of
parallel connected three-phase dc/ac inverter. Series resistors added
to the inverter output to maintain same current in each inverter of the
two parallel inverters, and to reduce the circulating current in the
parallel inverters to the minimum. High frequency third harmonic
injection PWM (THIPWM) employed to reduce the total harmonic
distortion and to make maximum use of the voltage source. DSP was
used to generate the THIPWM and the control algorithm for the
converter. Selected experimental results have been shown to validate
the proposed system.
Abstract: In a complex project environment, project teams face
multi-dimensional communication problems that can ultimately lead
to project breakdown. Team Performance varies in Face-to-Face
(FTF) environment versus groups working remotely in a computermediated
communication (CMC) environment. A brief review of the
Input_Process_Output model suggested by James E. Driskell, Paul H.
Radtke and Eduardo Salas in “Virtual Teams: Effects of
Technological Mediation on Team Performance (2003)", has been
done to develop the basis of this research. This model theoretically
analyzes the effects of technological mediation on team processes,
such as, cohesiveness, status and authority relations, counternormative
behavior and communication. An empirical study
described in this paper has been undertaken to test the
“cohesiveness" of diverse project teams in a multi-national
organization. This study uses both quantitative and qualitative
techniques for data gathering and analysis. These techniques include
interviews, questionnaires for data collection and graphical data
representation for analyzing the collected data. Computer-mediated
technology may impact team performance because of difference in
cohesiveness among teams and this difference may be moderated by
factors, such as, the type of communication environment, the type of
task and the temporal context of the team. Based on the reviewed
model, sets of hypotheses are devised and tested. This research,
reports on a study that compared team cohesiveness among virtual
teams using CMC and non-CMC communication mediums. The
findings suggest that CMC can help virtual teams increase team
cohesiveness among their members, making CMC an effective
medium for increasing productivity and team performance.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: We consider linear regression models where both input data (the values of independent variables) and output data (the observations of the dependent variable) are interval-censored. We introduce a possibilistic generalization of the least squares estimator, so called OLS-set for the interval model. This set captures the impact of the loss of information on the OLS estimator caused by interval censoring and provides a tool for quantification of this effect. We study complexity-theoretic properties of the OLS-set. We also deal with restricted versions of the general interval linear regression model, in particular the crisp input – interval output model. We give an argument that natural descriptions of the OLS-set in the crisp input – interval output cannot be computed in polynomial time. Then we derive easily computable approximations for the OLS-set which can be used instead of the exact description. We illustrate the approach by an example.
Abstract: Cosmic showers, during the transit through space, produce
sub - products as a result of interactions with the intergalactic
or interstellar medium which after entering earth generate secondary
particles called Extensive Air Shower (EAS). Detection and analysis
of High Energy Particle Showers involve a plethora of theoretical and
experimental works with a host of constraints resulting in inaccuracies
in measurements. Therefore, there exist a necessity to develop a
readily available system based on soft-computational approaches
which can be used for EAS analysis. This is due to the fact that soft
computational tools such as Artificial Neural Network (ANN)s can be
trained as classifiers to adapt and learn the surrounding variations. But
single classifiers fail to reach optimality of decision making in many
situations for which Multiple Classifier System (MCS) are preferred
to enhance the ability of the system to make decisions adjusting
to finer variations. This work describes the formation of an MCS
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN) with data inputs
from correlation mapping Self Organizing Map (SOM) blocks and
the output optimized by another SOM. The results show that the setup
can be adopted for real time practical applications for prediction
of primary energy and location of EAS from density values captured
using detectors in a circular grid.
Abstract: Since communications between tag and reader in RFID
system are by radio, anyone can access the tag and obtain its any
information. And a tag always replies with the same ID so that it is
hard to distinguish between a real and a fake tag. Thus, there are many
security problems in today-s RFID System. Firstly, unauthorized
reader can easily read the ID information of any Tag. Secondly,
Adversary can easily cheat the legitimate reader using the collected
Tag ID information, such as the any legitimate Tag. These security
problems can be typically solved by encryption of messages
transmitted between Tag and Reader and by authentication for Tag.
In this paper, to solve these security problems on RFID system, we
propose the Tag Authentication Scheme based on self shrinking
generator (SSG). SSG Algorithm using in our scheme is proposed by
W.Meier and O.Staffelbach in EUROCRYPT-94. This Algorithm is
organized that only one LFSR and selection logic in order to generate
random stream. Thus it is optimized to implement the hardware logic
on devices with extremely limited resource, and the output generating
from SSG at each time do role as random stream so that it is allow our
to design the light-weight authentication scheme with security against
some network attacks. Therefore, we propose the novel tag
authentication scheme which use SSG to encrypt the Tag-ID
transmitted from tag to reader and achieve authentication of tag.
Abstract: This paper addresses functional projective lag synchronization of Lorenz system with four unknown parameters, where the output of the master system lags behind the output of the slave system proportionally. For this purpose, an adaptive control law is proposed to make the states of two identical Lorenz systems asymptotically synchronize up. Based on Lyapunov stability theory, a novel criterion is given for asymptotical stability of the null solution of an error dynamics. Finally, some numerical examples are provided to show the effectiveness of our results.