Abstract: The genetic algorithm (GA) based solution techniques
are found suitable for optimization because of their ability of
simultaneous multidimensional search. Many GA-variants have been
tried in the past to solve optimal power flow (OPF), one of the
nonlinear problems of electric power system. The issues like
convergence speed and accuracy of the optimal solution obtained
after number of generations using GA techniques and handling
system constraints in OPF are subjects of discussion. The results
obtained for GA-Fuzzy OPF on various power systems have shown
faster convergence and lesser generation costs as compared to other
approaches. This paper presents an enhanced GA-Fuzzy OPF (EGAOPF)
using penalty factors to handle line flow constraints and load
bus voltage limits for both normal network and contingency case
with congestion. In addition to crossover and mutation rate
adaptation scheme that adapts crossover and mutation probabilities
for each generation based on fitness values of previous generations, a
block swap operator is also incorporated in proposed EGA-OPF. The
line flow limits and load bus voltage magnitude limits are handled by
incorporating line overflow and load voltage penalty factors
respectively in each chromosome fitness function. The effects of
different penalty factors settings are also analyzed under contingent
state.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of sensitivity analysis on port operation quantity provide useful information for managers to choose the best scenario for port planning with the lowest investment risks. Despite all limitations-due to data availability-the model offers a straightforward decision tools to port planners aspiring to achieve optimum port planning steps.
Abstract: An accurate optimal design of laminated composite
structures may present considerable difficulties due to the complexity
and multi-modality of the functional design space. The Big Bang
– Big Crunch (BB-BC) optimization method is a relatively new
technique and has already proved to be a valuable tool for structural
optimization. In the present study the exceptional efficiency of the
method is demonstrated by an example of the lay-up optimization
of multilayered anisotropic cylinders based on a three-dimensional
elasticity solution. It is shown that, due to its simplicity and speed,
the BB-BC is much more efficient for this class of problems when
compared to the genetic algorithms.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: Multirate multimedia delivery applications in multihop Wireless Mesh Network (WMN) are data redundant and delay-sensitive, which brings a lot of challenges for designing efficient transmission systems. In this paper, we propose a new cross layer resource allocation scheme to minimize the receiver side distortion within the delay bound requirements, by exploring application layer Position and Value (P-V) diversity as well as the multihop Effective Capacity (EC). We specifically consider image transmission optimization here. First of all, the maximum supportable source traffic rate is identified by exploring the multihop Effective Capacity (EC) model. Furthermore, the optimal source coding rate is selected according to the P-V diversity of multirate media streaming, which significantly increases the decoded media quality. Simulation results show the proposed approach improved media quality significantly compared with traditional approaches under the same QoS requirements.
Abstract: Fossil fuel-firing power plants dominate electric
power generation in Taiwan, which are also the major contributor to
Green House gases (GHG). CO2 is the most important greenhouse
gas that cause global warming. This paper penetrates the relationship
between carbon trading for GHG reduction and power generation
expansion planning (GEP) problem for the electrical utility. The
Particle Swarm Optimization (PSO) Algorithm is presented to deal
with the generation expansion planning strategy of the utility with
independent power providers (IPPs). The utility has to take both the
IPPs- participation and environment impact into account when a new
generation unit is considering expanded from view of supply side.
Abstract: Cross layer optimization based on utility functions has
been recently studied extensively, meanwhile, numerous types of
utility functions have been examined in the corresponding literature.
However, a major drawback is that most utility functions take a fixed
mathematical form or are based on simple combining, which can
not fully exploit available information. In this paper, we formulate a
framework of cross layer optimization based on Adaptively Weighted
Utility Functions (AWUF) for fairness balancing in OFDMA networks.
Under this framework, a two-step allocation algorithm is
provided as a sub-optimal solution, whose control parameters can be
updated in real-time to accommodate instantaneous QoS constrains.
The simulation results show that the proposed algorithm achieves
high throughput while balancing the fairness among multiple users.
Abstract: State-of-the-art methods for secondary structure (Porter, Psi-PRED, SAM-T99sec, Sable) and solvent accessibility (Sable, ACCpro) predictions use evolutionary profiles represented by the position specific scoring matrix (PSSM). It has been demonstrated that evolutionary profiles are the most important features in the feature space for these predictions. Unfortunately applying PSSM matrix leads to high dimensional feature spaces that may create problems with parameter optimization and generalization. Several recently published suggested that applying feature extraction for the PSSM matrix may result in improvements in secondary structure predictions. However, none of the top performing methods considered here utilizes dimensionality reduction to improve generalization. In the present study, we used simple and fast methods for features selection (t-statistics, information gain) that allow us to decrease the dimensionality of PSSM matrix by 75% and improve generalization in the case of secondary structure prediction compared to the Sable server.
Abstract: In this paper we present a Feed-Foward Neural
Networks Autoregressive (FFNN-AR) model with genetic algorithms
training optimization in order to predict the gross domestic product
growth of six countries. Specifically we propose a kind of weighted
regression, which can be used for econometric purposes, where the
initial inputs are multiplied by the neural networks final optimum
weights from input-hidden layer of the training process. The
forecasts are compared with those of the ordinary autoregressive
model and we conclude that the proposed regression-s forecasting
results outperform significant those of autoregressive model.
Moreover this technique can be used in Autoregressive-Moving
Average models, with and without exogenous inputs, as also the
training process with genetics algorithms optimization can be
replaced by the error back-propagation algorithm.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: This paper presents an analytical model to estimate
the cost of an optimized design of reinforced concrete isolated
footing base on structural safety. Flexural and optimized formulas for
square and rectangular footingare derived base on ACI building code
of design, material cost and optimization. The optimization
constraints consist of upper and lower limits of depth and area of
steel. Footing depth and area of reinforcing steel are to be minimized
to yield the optimal footing dimensions. Optimized footing materials
cost of concrete, reinforcing steel and formwork of the designed
sections are computed. Total cost factor TCF and other cost factors
are developed to generalize and simplify the calculations of footing
material cost. Numerical examples are presented to illustrate the
model capability of estimating the material cost of the footing for a
desired axial load.
Abstract: Order reduction of linear-time invariant systems employing two methods; one using the advantages of Routh approximation and other by an evolutionary technique is presented in this paper. In Routh approximation method the denominator of the reduced order model is obtained using Routh approximation while the numerator of the reduced order model is determined using the indirect approach of retaining the time moments and/or Markov parameters of original system. By this method the reduced order model guarantees stability if the original high order model is stable. In the second method Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical examples.
Abstract: This paper proposes a new version of the Particle
Swarm Optimization (PSO) namely, Modified PSO (MPSO) for
model order formulation of Single Input Single Output (SISO) linear
time invariant continuous systems. In the General PSO, the
movement of a particle is governed by three behaviors namely
inertia, cognitive and social. The cognitive behavior helps the
particle to remember its previous visited best position. In Modified
PSO technique split the cognitive behavior into two sections like
previous visited best position and also previous visited worst
position. This modification helps the particle to search the target very
effectively. MPSO approach is proposed to formulate the higher
order model. The method based on the minimization of error
between the transient responses of original higher order model and
the reduced order model pertaining to the unit step input. The results
obtained are compared with the earlier techniques utilized, to validate
its ease of computation. The proposed method is illustrated through
numerical example from literature.
Abstract: The authors of this work indicate by means of a concrete example that it is possible to apply efficaciously the method of multiple criteria programming in dealing with the problem of determining the optimal production plan for a certain period of time. The work presents: (1) the selection of optimization criteria, (2) the setting of the problem of determining an optimal production plan, (3) the setting of the model of multiple criteria programming in finding a solution to a given problem, (4) the revised surrogate trade-off method, (5) generalized multicriteria model for solving production planning problem and problem of choosing technological variants in the metal manufacturing industry. In the final part of this work the authors reflect on the application of the method of multiple criteria programming while determining the optimal production plan in manufacturing enterprises.
Abstract: Global approximation using metamodel for complex
mathematical function or computer model over a large variable
domain is often needed in sensibility analysis, computer simulation,
optimal control, and global design optimization of complex, multiphysics
systems. To overcome the limitations of the existing
response surface (RS), surrogate or metamodel modeling methods for
complex models over large variable domain, a new adaptive and
regressive RS modeling method using quadratic functions and local
area model improvement schemes is introduced. The method applies
an iterative and Latin hypercube sampling based RS update process,
divides the entire domain of design variables into multiple cells,
identifies rougher cells with large modeling error, and further divides
these cells along the roughest dimension direction. A small number
of additional sampling points from the original, expensive model are
added over the small and isolated rough cells to improve the RS
model locally until the model accuracy criteria are satisfied. The
method then combines local RS cells to regenerate the global RS
model with satisfactory accuracy. An effective RS cells sorting
algorithm is also introduced to improve the efficiency of model
evaluation. Benchmark tests are presented and use of the new
metamodeling method to replace complex hybrid electrical vehicle
powertrain performance model in vehicle design optimization and
optimal control are discussed.
Abstract: Semnan is a city in semnan province, northern Iran
with a population estimated at 119,778 inhabitants. It is the
provincial capital of semnan province. Iran is a developing country
and construction is a basic factor of developing too. Hence, Semnan
city needs to a special programming for construction of buildings,
structures and infrastructures. Semnan municipality tries to begin this
program. In addition to, city has some historical monuments which
can be interesting for tourists. Hence, Semnan inhabitants can benefit
from tourist industry. Optimization of Energy in construction
industry is another activity of this municipality and the inhabitants
who execute these regulations receive some discounts. Many parts of
Iran such as semnan are located in highly seismic zones and
structures must be constructed safe e.g., according to recent seismic
codes. In this paper opportunities of IT in construction industry of
Iran are investigated in three categories. Pre-construction phase,
construction phase and earthquake disaster mitigation are studied.
Studies show that information technology can be used in these items
for reducing the losses and increasing the benefits. Both government
and private sectors must contribute to this strategic project for
obtaining the best result.
Abstract: Activated carbon was prepared from agricultural waste “almond (Prunus amygdalus) nut shells" by chemical activation with phosphoric acid as an activating agent at 450 °C for 24 hr soaking time. The physical and chemical properties were analyzed. The adsorption of chromium VI from aqueous solution on almond nut shell activated carbon (ASAC) was investigated. The adsorption process parameters pH, agitation speed, agitation time, adsorbent dose were optimized. 98% of Cr VI was sorbed at pH 2 and stirring speed 200 rpm.. Surface structure showed that ASAC has a spongy type structure showing large number of pores
Abstract: Over Current Relays (OCRs) and Directional Over Current Relays (DOCRs) are widely used for the radial protection and ring sub transmission protection systems and for distribution systems. All previous work formulates the DOCR coordination problem either as a Non-Linear Programming (NLP) for TDS and Ip or as a Linear Programming (LP) for TDS using recently a social behavior (Particle Swarm Optimization techniques) introduced to the work. In this paper, a Modified Particle Swarm Optimization (MPSO) technique is discussed for the optimal settings of DOCRs in power systems as a Non-Linear Programming problem for finding Ip values of the relays and for finding the TDS setting as a linear programming problem. The calculation of the Time Dial Setting (TDS) and the pickup current (Ip) setting of the relays is the core of the coordination study. PSO technique is considered as realistic and powerful solution schemes to obtain the global or quasi global optimum in optimization problem.
Abstract: In this paper, novel statistical sampling based equalization techniques and CNN based detection are proposed to increase the spectral efficiency of multiuser communication systems over fading channels. Multiuser communication combined with selective fading can result in interferences which severely deteriorate the quality of service in wireless data transmission (e.g. CDMA in mobile communication). The paper introduces new equalization methods to combat interferences by minimizing the Bit Error Rate (BER) as a function of the equalizer coefficients. This provides higher performance than the traditional Minimum Mean Square Error equalization. Since the calculation of BER as a function of the equalizer coefficients is of exponential complexity, statistical sampling methods are proposed to approximate the gradient which yields fast equalization and superior performance to the traditional algorithms. Efficient estimation of the gradient is achieved by using stratified sampling and the Li-Silvester bounds. A simple mechanism is derived to identify the dominant samples in real-time, for the sake of efficient estimation. The equalizer weights are adapted recursively by minimizing the estimated BER. The near-optimal performance of the new algorithms is also demonstrated by extensive simulations. The paper has also developed a (Cellular Neural Network) CNN based approach to detection. In this case fast quadratic optimization has been carried out by t, whereas the task of equalizer is to ensure the required template structure (sparseness) for the CNN. The performance of the method has also been analyzed by simulations.