Abstract: This research adapts experimental design to investigate
the effect of conditioning or not and pre-exposure or not on brand
attitude, so it is a 2×2=4 factorial design. The results show that the
brand attitude of conditioning group is significantly higher than that of
unconditioning group. The brand attitude with pre-exposure is
significantly higher than that without pre-exposure. Conditioning or
not and pre-exposure or not have significant interaction. No matter the
celebrity is pre-exposure or not, the brand attitude is higher under
conditioning process.
Abstract: This paper presents a systematic approach for the
design of power system stabilizer using genetic algorithm and
investigates the robustness of the GA based PSS. The proposed
approach employs GA search for optimal setting of PSS parameters.
The performance of the proposed GPSS under small and large
disturbances, loading conditions and system parameters is tested.
The eigenvalue analysis and nonlinear simulation results show the
effectiveness of the GPSS to damp out the system oscillations. It is
found tat the dynamic performance with the GPSS shows improved
results, over conventionally tuned PSS over a wide range of
operating conditions.
Abstract: Adaptive control involves modifying the control law
used by the controller to cope with the fact that the parameters of the
system being controlled change drastically due to change in
environmental conditions or in system itself. This technique is based
on the fundamental characteristic of adaptation of living organism.
The adaptive control process is one that continuously and
automatically measures the dynamic behavior of plant, compares it
with the desired output and uses the difference to vary adjustable
system parameters or to generate an actuating signal in such a way so
that optimal performance can be maintained regardless of system
changes. This paper deals with application of model reference
adaptive control scheme in first order system. The rule which is used
for this application is MIT rule. This paper also shows the effect of
adaptation gain on the system performance. Simulation is done in
MATLAB and results are discussed in detail.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: MultiProtocol Label Switching (MPLS) is an
emerging technology that aims to address many of the existing issues
associated with packet forwarding in today-s Internetworking
environment. It provides a method of forwarding packets at a high
rate of speed by combining the speed and performance of Layer 2
with the scalability and IP intelligence of Layer 3. In a traditional IP
(Internet Protocol) routing network, a router analyzes the destination
IP address contained in the packet header. The router independently
determines the next hop for the packet using the destination IP
address and the interior gateway protocol. This process is repeated at
each hop to deliver the packet to its final destination. In contrast, in
the MPLS forwarding paradigm routers on the edge of the network
(label edge routers) attach labels to packets based on the forwarding
Equivalence class (FEC). Packets are then forwarded through the
MPLS domain, based on their associated FECs , through swapping
the labels by routers in the core of the network called label switch
routers. The act of simply swapping the label instead of referencing
the IP header of the packet in the routing table at each hop provides
a more efficient manner of forwarding packets, which in turn allows
the opportunity for traffic to be forwarded at tremendous speeds and
to have granular control over the path taken by a packet. This paper
deals with the process of MPLS forwarding mechanism,
implementation of MPLS datapath , and test results showing the
performance comparison of MPLS and IP routing. The discussion
will focus primarily on MPLS IP packet networks – by far the
most common application of MPLS today.
Abstract: The Integrated Management of Child illnesses (IMCI) and the surveillance Health Information Systems (HIS) are related strategies that are designed to manage child illnesses and community practices of diseases. However, both strategies do not function well together because of classification incompatibilities and, as such, are difficult to use by health care personnel in rural areas where a majority of people lack the basic knowledge of interpreting disease classification from these methods. This paper discusses a single approach on how a stand-alone expert system can be used as a prompt diagnostic tool for all cases of illnesses presented. The system combines the action-oriented IMCI and the disease-oriented HIS approaches to diagnose malaria and typhoid fever in the rural areas of the Niger-delta region.
Abstract: Image coding based on clustering provides immediate
access to targeted features of interest in a high quality decoded
image. This approach is useful for intelligent devices, as well as for
multimedia content-based description standards. The result of image
clustering cannot be precise in some positions especially on pixels
with edge information which produce ambiguity among the clusters.
Even with a good enhancement operator based on PDE, the quality of
the decoded image will highly depend on the clustering process. In
this paper, we introduce an ambiguity cluster in image coding to
represent pixels with vagueness properties. The presence of such
cluster allows preserving some details inherent to edges as well for
uncertain pixels. It will also be very useful during the decoding phase
in which an anisotropic diffusion operator, such as Perona-Malik,
enhances the quality of the restored image. This work also offers a
comparative study to demonstrate the effectiveness of a fuzzy
clustering technique in detecting the ambiguity cluster without losing
lot of the essential image information. Several experiments have been
carried out to demonstrate the usefulness of ambiguity concept in
image compression. The coding results and the performance of the
proposed algorithms are discussed in terms of the peak signal-tonoise
ratio and the quantity of ambiguous pixels.
Abstract: Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.
Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: Ventilation is a fundamental requirement for
occupant health and indoor air quality in buildings. Natural
ventilation can be used as a design strategy in free-running
buildings to:
• Renew indoor air with fresh outside air and lower room
temperatures at times when the outdoor air is cooler.
• Promote air flow to cool down the building structure
(structural cooling).
• Promote occupant physiological cooling processes
(comfort cooling).
This paper focuses on ways in which ventilation can
provide the mechanism for heat dissipation and cooling of the
building structure..It also discusses use of ventilation as a
means of increasing air movement to improve comfort when
indoor air temperatures are too high. The main influencing
factors and design considerations and quantitative guidelines
to help meet the design objectives are also discussed.
Abstract: According to the interaction of inflation and
unemployment, expectation of the rate of inflation in Croatia is
estimated. The interaction between inflation and unemployment is
shown by model based on three first-order differential i.e. difference
equations: Phillips relation, adaptive expectations equation and
monetary-policy equation. The resulting equation is second order
differential i.e. difference equation which describes the time path of
inflation. The data of the rate of inflation and the rate of
unemployment are used for parameters estimation. On the basis of
the estimated time paths, the stability and convergence analysis is
done for the rate of inflation.
Abstract: Scale Time Offset Robust Modulation (STORM) [1]–
[3] is a high bandwidth waveform design that adds time-scale
to embedded reference modulations using only time-delay [4]. In
an environment where each user has a specific delay and scale,
identification of the user with the highest signal power and that
user-s phase is facilitated by the STORM processor. Both of these
parameters are required in an efficient multiuser detection algorithm.
In this paper, the STORM modulation approach is evaluated with
a direct sequence spread quadrature phase shift keying (DS-QPSK)
system. A misconception of the STORM time scale modulation is that
a fine temporal resolution is required at the receiver. STORM will
be applied to a QPSK code division multiaccess (CDMA) system
by modifying the spreading codes. Specifically, the in-phase code
will use a typical spreading code, and the quadrature code will
use a time-delayed and time-scaled version of the in-phase code.
Subsequently, the same temporal resolution in the receiver is required
before and after the application of STORM. In this paper, the bit error
performance of STORM in a synchronous CDMA system is evaluated
and compared to theory, and the bit error performance of STORM
incorporated in a single user WCDMA downlink is presented to
demonstrate the applicability of STORM in a modern communication
system.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.
Abstract: Throughout this paper, a relatively new technique, the Tabu search variable selection model, is elaborated showing how it can be efficiently applied within the financial world whenever researchers come across the selection of a subset of variables from a whole set of descriptive variables under analysis. In the field of financial prediction, researchers often have to select a subset of variables from a larger set to solve different type of problems such as corporate bankruptcy prediction, personal bankruptcy prediction, mortgage, credit scoring and the Arbitrage Pricing Model (APM). Consequently, to demonstrate how the method operates and to illustrate its usefulness as well as its superiority compared to other commonly used methods, the Tabu search algorithm for variable selection is compared to two main alternative search procedures namely, the stepwise regression and the maximum R 2 improvement method. The Tabu search is then implemented in finance; where it attempts to predict corporate bankruptcy by selecting the most appropriate financial ratios and thus creating its own prediction score equation. In comparison to other methods, mostly the Altman Z-Score model, the Tabu search model produces a higher success rate in predicting correctly the failure of firms or the continuous running of existing entities.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: In recent years, most of the regions in the world are
exposed to degradation and erosion caused by increasing
population and over use of land resources. The understanding of
the most important factors on soil erosion and sediment yield are
the main keys for decision making and planning. In this study, the
sediment yield and soil erosion were estimated and the priority of
different soil erosion factors used in the MPSIAC method of soil
erosion estimation is evaluated in AliAbad watershed in southwest
of Isfahan Province, Iran. Different information layers of the
parameters were created using a GIS technique. Then, a
multivariate procedure was applied to estimate sediment yield and
to find the most important factors of soil erosion in the model. The
results showed that land use, geology, land and soil cover are the
most important factors describing the soil erosion estimated by
MPSIAC model.
Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: In this paper, a pipelined version of genetic algorithm,
called PLGA, and a corresponding hardware platform are described.
The basic operations of conventional GA (CGA) are made pipelined
using an appropriate selection scheme. The selection operator, used
here, is stochastic in nature and is called SA-selection. This helps
maintaining the basic generational nature of the proposed pipelined
GA (PLGA). A number of benchmark problems are used to compare
the performances of conventional roulette-wheel selection and the
SA-selection. These include unimodal and multimodal functions with
dimensionality varying from very small to very large. It is seen that
the SA-selection scheme is giving comparable performances with
respect to the classical roulette-wheel selection scheme, for all the
instances, when quality of solutions and rate of convergence are considered.
The speedups obtained by PLGA for different benchmarks
are found to be significant. It is shown that a complete hardware
pipeline can be developed using the proposed scheme, if parallel
evaluation of the fitness expression is possible. In this connection
a low-cost but very fast hardware evaluation unit is described.
Results of simulation experiments show that in a pipelined hardware
environment, PLGA will be much faster than CGA. In terms of
efficiency, PLGA is found to outperform parallel GA (PGA) also.
Abstract: The feasibility of employing solar radiation for
enhanced Fenton process in degradation of combined chlorpyrifos,
cypermethrin and chlorothalonil pesticides was examined. The effect
of various operating conditions of the process on biodegradability
improvement and mineralization of the pesticides were also
evaluated. The optimum operating conditions for treatment of
aqueous solution containing 100, 50 and 250 mg L-1 chlorpyrifos
cypermethrin and chlorothalonil, respectively were observed to be
H2O2/COD molar ratio 2, H2O2/Fe2+ molar ratio 25 and pH 3. Under
the optimum operating conditions, complete degradation of the
pesticides occurred in 1 min. Biodegradability (BOD5/COD)
increased from zero to 0.36 in 60 min, and COD and TOC removal
were 74.19 and 58.32%, respectively in 60 min. Due to
mineralization of organic carbon, decrease in ammonia-nitrogen from
22 to 4.3 mg L-1 and increase in nitrate from 0.7 to 18.1 mg L-1 in
60 min were recorded. The study indicated that solar photo-Fenton
process can be used for pretreatment of chlorpyrifos, cypermethrin
and chlorothalonil pesticides in aqueous solution for further
biological treatment.