Abstract: This paper present the experimental work of double
unit tunnel form building (TFB) subjected to in-plane lateral cyclic
loading. A one third scale of 3-storey double unit of TFB is tested
until its strength degradation. Then, the TFB is repaired and
retrofitted using additional shear wall, steel angle and CFRP sheet.
The crack patterns, lateral strength, stiffness, ductility and equivalent
viscous damping (EVD) were analyzed and compared before and
after repair and retrofit. The result indicates that the lateral strength
increases by 22% in pushing and 27% in pulling direction. Moreover,
the stiffness and ductility obtained before and after retrofit increase
tremendously by 87.87% and 39.66%, respectively. Meanwhile, the
energy absorption measured by equivalent viscous damping obtained
after retrofit increase by 12.34% in pulling direction. It can be
concluded that the proposed retrofit method is capable to increase the
lateral strength capacity, stiffness and energy absorption of double
unit TFB.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: Climate change will affect the hydrological cycle in
many different ways such as increase in evaporation and rainfalls.
There have been growing interests among researchers to identify the
nature of trends in historical rainfall data in many different parts of
the world. This paper examines the trends in annual maximum
rainfall data from 30 stations in New South Wales, Australia by using
two non-parametric tests, Mann-Kendall (MK) and Spearman’s Rho
(SR). Rainfall data were analyzed for fifteen different durations
ranging from 6 min to 3 days. It is found that the sub-hourly
durations (6, 12, 18, 24, 30 and 48 minutes) show statistically
significant positive (upward) trends whereas longer duration (subdaily
and daily) events generally show a statistically significant
negative (downward) trend. It is also found that the MK test and SR
test provide notably different results for some rainfall event durations
considered in this study. Since shorter duration sub-hourly rainfall
events show positive trends at many stations, the design rainfall data
based on stationary frequency analysis for these durations need to be
adjusted to account for the impact of climate change. These shorter
durations are more relevant to many urban development projects
based on smaller catchments having a much shorter response time.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: Esterification of p-bromo-m-cresol led to formation of
2-(4-bromo-3-methylphenoxy)acetate (1). 2-(4-Bromo-3-methyl
phenoxy)acetohydrazide (2) is derived from Compound (1) by
hydrazination. Compound (2) was reacted with different aromatic
aldehydes to yield N-(substituted benzylidiene)-2-(4-bromo-3-methyl
phenoxy)acetamide(3a-c). Cyclization of compound (3a-c) with
thioglycolic acid yielded 2-(4-bromo-3-methylphenoxy)-N-(4-oxo-2-
arylthiazolidin-3-yl) acetamide (4a-c). The newly synthesized
compounds were characterized on the basis of spectral studies and
evaluated for antibacterial and antifungal activities.
Abstract: In this paper, we have proposed a parallel IDS and
honeypot based approach to detect and analyze the unknown and
known attack taxonomy for improving the IDS performance and
protecting the network from intruders. The main theme of our
approach is to record and analyze the intruder activities by using both
the low and high interaction honeypots. Our architecture aims to
achieve the required goals by combing signature based IDS,
honeypots and generate the new signatures. The paper describes the
basic component, design and implementation of this approach and
also demonstrates the effectiveness of this approach to reduce the
probability of network attacks.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Molluca Collision Zone is located at the junction of
the Eurasian, Australian, Pacific and the Philippines plates. Between
the Sangihe arc, west of the collision zone, and to the east of
Halmahera arc is active collision and convex toward the Molluca Sea.
This research will analyze the behavior of earthquake occurrence in
Molluca Collision Zone related to the distributions of an earthquake
in each partition regions, determining the type of distribution of a
occurrence earthquake of partition regions, and the mean occurence
of earthquakes each partition regions, and the correlation between the
partitions region. We calculate number of earthquakes using partition
method and its behavioral using conventional statistical methods. In
this research, we used data of shallow earthquakes type and its
magnitudes ≥4 SR (period 1964-2013). From the results, we can
classify partitioned regions based on the correlation into two classes:
strong and very strong. This classification can be used for early
warning system in disaster management.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: The study identified the socio-economic and
demographic factors of both married and unmarried females in third
world countries. Almost all the countries have same problems but we
have selected Pakistan as a sample country. The main purpose of this
study was to examine which factors forced women to participate in
labor market. So the best technique of data collection was survey of
both married and unmarried females between the ages of 20 to 49.
Two models (probit and logit) were used to analyze the factors which
effect on FLFP. The result showed that some factors e.g. age;
education and marital status have significant effect on FLFP. The
findings showed that educated women and those who belong to joint
families are more participate because of financial pressure.
Abstract: The reachable set bounding estimation for distributed
delay systems with disturbances is a new problem. In this paper,we
consider this problem subject to not only time varying delay and
polytopic uncertainties but also distributed delay systems which is
not studied fully untill now. we can obtain improved non-ellipsoidal
reachable set estimation for neural networks with time-varying delay
by the maximal Lyapunov-Krasovskii fuctional which is constructed
as the pointwise maximum of a family of Lyapunov-Krasovskii
fuctionals corresponds to vertexes of uncertain polytope.On the other
hand,matrix inequalities containing only one scalar and Matlabs
LMI Toolbox is utilized to give a non-ellipsoidal description of the
reachable set.finally,numerical examples are given to illustrate the
existing results.
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: The psychological impact of peer influence on its
individual group members, can make them resist HIV/AIDS
counselling and testing. This study investigated the correlate of peer
influence and resistance to HIV/AIDS counselling and testing among
students in tertiary institutions in Kano state, Nigeria. To achieve
this, three null hypotheses were postulated and tested. Cross-
Sectional Survey Design was employed in which 1512 sample was
selected from a student population of 104,841.Simple Random
Sampling was used in the selection. A self-developed 20-item scale
called Peer Influence and Psychological Resistance Inventory
(PIPRI) was used for data collection. Pearson Product Moment
Correlation (PPMCC) via test-retest method was applied to estimate a
reliability coefficient of 0.86 for the scale. Data obtained was
analyzed using t-test and PPMCC at 0.05 level of confidence. Results
reveal 26.3% (397) of the respondents being influenced by their peer
group, while 39.8% showed resistance. Also, the t-tests and PPMCC
statistics were greater than their respective critical values. This shows
that there was a significant gender difference in peer influence and a
difference between peer influence and resistance to HIV/AIDS
counselling and testing. However, a positive relationship between
peer influence and resistance to HIV/AIDS counselling and testing
was shown. A major recommendation offered suggests the use of
reinforcement and social support for positive attitudes and
maintenance of safe behaviour among students who patronize
HIV/AIDS counselling.
Abstract: This paper presents reliability indices evaluation of the
rotor core magnetization of the induction motor operated as a self
excited induction generator by using probability distribution approach
and Monte Carlo simulation. Parallel capacitors with calculated
minimum capacitive value across the terminals of the induction motor
operated as a SEIG with unregulated shaft speed have been connected
during the experimental study. A three phase, 4 poles, 50Hz, 5.5 hp,
12.3A, 230V induction motor coupled with DC Shunt Motor was
tested in the electrical machine laboratory with variable reactive loads.
Based on this experimental study, it is possible to choose a reliable
induction machines operated as a SEIG for unregulated renewable
energy application in remote area or where grid is not available.
Failure density function, cumulative failure distribution function,
survivor function, hazard model, probability of success and
probability of failure for reliability evaluation of the three phase
induction motor operating as a SEIG have been presented graphically
in this paper.
Abstract: In this paper, the effect of admixtures on the tensional
strength of concrete in Urmia-lake water have been investigated. We
made different types of concretes with the ratio of w/c and replaced
different percentages of micro-silica, air-entraining, super plasticizer,
corrosion-inhibiting, and caulk with two types of cement I and II as
well as investigating in both ordinary water and Urmia-lake water.
The tensional strength was investigated on these samples.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: Nations are still finding it quite difficult to win mega
sport competitions despite the major contribution of sport to society
in terms of social and economic development, personal health, and in
education. Even though the world of sports has been transformed into
a huge global economy, it is important to note that the first step of
sport is usually its introduction to children at school through physical
education or PE. In other words, nations who do not win mega sport
competitions also suffer from a weak and neglected PE system. This
problem of the neglect of PE systems is the main motivation of this
research aimed at examining the factors affecting the perceived
awareness of physical education teachers on the ICTs that are
adoptable for the teaching and learning of physical education. Two
types of research objectives will materialize this aim: relevant
theories will be identified in relation to the analysis of the perceived
ICT awareness of PE teachers and subsequent models will be
compiled and designed from existing literature; the empirical testing
of such theories and models will also be achieved through the survey
of PE teachers from the Camperdown magisterial district of the
KwaZulu-Natal province of South Africa. The main hypothesis at the
heart of this study is the relationship between the demographics of PE
teachers, their behavior both as individuals and as social entities, and
their perceived awareness of the ICTs that are adoptable for PE, as
postulated by existing literature; except that this study categorizes
human behavior under performance expectancy, computer attitude,
and social influence. This hypothesis was partially confirmed by the
survey conducted by this research in the sense that performance
expectancy and teachers’ age, gender, computer usage, and class size
were found to be the only factors affecting their awareness of ICTs
for physical education.