Abstract: This paper reports the viability of developing Zn-27Al
alloy matrix hybrid composites reinforced with alumina, graphite and
fly ash (solid waste bye product of coal in thermal power plants).
This research work was aimed at developing low cost-high
performance Zn-27Al matrix composite with low density. Alumina
particulates (Al2O3), graphite added with 0, 2, 3, 4 and 5 wt% fly ash
were utilized to prepare 10wt% reinforcing phase with Zn-27Al alloy
as matrix using two-step stir casting method. Density measurement,
estimated percentage porosity, tensile testing, micro hardness
measurement and optical microscopy were used to assess the
performance of the composites produced. The results show that the
hardness, ultimate tensile strength, and percent elongation of the
hybrid composites decrease with increase in fly ash content. The
maximum decrease in hardness and ultimate tensile strength of
13.72% and 15.25% respectively were observed for composite grade
containing 5wt% fly ash. The percentage elongation of composite
sample without fly ash is 8.9% which is comparable with that of the
sample containing 2wt% fly ash with percentage elongation of 8.8%.
The fracture toughness of the fly ash containing composites was
however superior to those of composites without fly ash with 5wt%
fly ash containing composite exhibiting the highest fracture
toughness. The results show that fly ash can be utilized as
complementary reinforcement in ZA-27 alloy matrix composite to
reduce cost.
Abstract: Rapid population growth, urbanization and
industrialization are known as the most important factors of
environment problems. Elimination and management of solid wastes
are also within the most important environment problems. One of the
main problems in solid waste management is the selection of the best
site for elimination of solid wastes. Lately, Geographical Information
System (GIS) has been used for easing selection of landfill area. GIS
has the ability of imitating necessary economic, environmental and
political limitations. They play an important role for the site selection
of landfill area as a decision support tool. In this study; map layers will be studied for minimum effect of
environmental, social and cultural factors and maximum effect for
engineering/economic factors for site selection of landfill areas and
using GIS for a decision support mechanism in solid waste landfill
areas site selection will be presented in Aksaray/Turkey city,
Güzelyurt district practice.
Abstract: The consumption of food contaminated with molds
(microscopic filamentous fungi) and their toxic metabolites results in
the development of food-borne mycotoxicosis. The spores of molds
are ubiquitously spread in the environment and can be detected
everywhere. Ochratoxin A is a toxic and potentially carcinogenic
fungal toxin found in a variety of food commodities. In this study, the
mycological quality of various ready-to-eat local and imported pork
meat and meat byproducts sold in Egyptian markets were assessed
and the presence of various molds was determined in pork used as a
raw material, edible organs as liver and kidney as well as in
fermented raw meat by-products. The study assessed the mycological
quality of pork raw meat and their by-products sold in commercial
shops in Cairo, Egypt. Mycological analysis was conducted on
(n=110) samples which included pig’s livers and kidneys from
Egyptian Bassatin slaughter house; local and imported processed
pork meat by-products from Egyptian pork markets. The isolates
were identified using traditional mycological and biochemical tests.
All kidney and liver samples were positive to molds growth while all
byproducts were negative. Ochratoxin A levels were quantitatively
analyzed using the high performance liquid chromatography (HPLC)
and the highest results were present in kidney 7.51 part per billion
(ppb) followed by minced meat 6.19 ppb generally the local samples
showed higher levels than the imported ones. To the best of our
knowledge, this is the first report on mycotoxins detection and
quantification from pork by-products in Egypt.
Abstract: The purpose of the study is to find out relation of
moral massage between the authority and globalization in proverb.
Proverb is one of the many forms of cultural identity of the
Indonesian/Malay people filled with moral values. The values
contained within those proverbs are beneficial not only to the society,
but also to those who held power amidst on this era of globalization.
The method being used is qualitative research through content
analysis which is done by describing and uncovering the forms and
meanings of proverbs used within Indonesia Minangkabau society.
Sources for this study’s data were extracted from a Minangkabau
native speaker in the sub district of Tanah Abang, Jakarta. Said
sources were retrieved through a series of interviews with the
Minangkabau native speaker, whose speech is still adorned with
idiomatic expressions. The research findings show that there are 30
existed proverbs or idiomatic expressions in the Minangkabau
language often used by its indigenous people. The thirty data contain
moral values which are closely interwoven with the matter of power
and globalization. Analytical results show that the fourteen moral
values contained within proverbs reflect a firm connection between
rule and power in globalization; such as: responsible, brave,
togetherness and consensus, tolerance, politeness, thorough and
meticulous, honest and keeping promise, ingenious and learning,
care, self-correction, be fair, alert, arbitrary, self-awareness.
Structurally, proverbs possess an unchangeably formal construction;
symbolically, proverbs possess meanings that are clearly decided
through ethnographic communicative factors along with situational
and cultural contexts. Values contained within proverbs may be used
as a guide in social management, be it between fellow men, between
men and nature, or even between men and their Creator. Therefore,
the meanings and values contained within the morals of proverbs
could also be utilized as a counsel for those who rule and in charge of
power in order to stem the tides of globalization that had already
spread into sectoral, territorial and educational continuums.
Abstract: Plate is one of the popular structural elements used in a wide range of industries and structures. They may be subjected to blast loads during explosion events, missile attacks or aircraft attacks. This study is to investigate dynamic responses of the rectangular plate subjected to explosive loads. The effects of material properties and plate thickness on responses of the plate are to be investigated. The compressive pressure is applied to the surface of the plate. Different amounts of thickness in the range from 1mm to 30mm are considered for the plate to evaluate the changes in responses of the plate with respect to plate thickness. Two different properties are considered for the steel. First, the analysis is performed by considering only the elastic-plastic properties for the steel plate. Later on damping is considered to investigate its effects on the responses of the plate. To do analysis, numerical method using a finite element based package ABAQUS is applied. Finally, dynamic responses and graphs showing the relation between maximum displacement of the plate and aim parameters are provided.
Abstract: The study focused on the analysis of the Adjusted
Rorschach Comprehensive System’s responses. The objective of this
study is to analyse the participants’ response rate of the Adjusted
Rorschach Comprehensive System with regards to critical
psychology approach. The use of critical psychology theory in this
study was crucial because it responds to the current inadequate
western theory or practice in the field of psychology. The study
adopted a qualitative approach and a case study design. The study
was grounded on interpretivist paradigm. The sample size comprised
six learners (three boys and three girls, aged of 14 years) from
historically disadvantaged school in the Western Cape, South Africa.
The Adjusted Rorschach Comprehensive System (ARCS)
administration procedure, biographical information, semi-structured
interviews, and observation were used to collect data. Data was
analysed using thematic framework. The study found out that, factors
that increased the response rates during the administration of ARCS
were, language, seating arrangement, drawing, viewing, and
describing. The study recommended that, psychological test
designers take into consideration the philosophy or worldviews of the
local people for whom the test is designed to minimize low response
rates.
Abstract: As a basic physiology need, threat to sufficient food
production is threat to human survival. Food security has been an
issue that has gained global concern. This paper looks at the food
security in Nigeria by assessing the availability of food and
accessibility of the available food. The paper employed multiple
linear regression technique and graphic trends of growth rates of
relevant variables to show the situation of food security in Nigeria.
Results of the tests revealed that population growth rate was higher
than the growth rate of food availability in Nigeria for the earlier
period of the study. Commercial bank credit to agricultural sector,
foreign exchange utilization for food and the Agricultural Credit
Guarantee Scheme Fund (ACGSF) contributed significantly to food
availability in Nigeria. Food prices grew at a faster rate than the
average income level, making it difficult to access sufficient food. It
implies that prior to the year 2012; there was insufficient food to feed
the Nigerian populace. However, continued credit to the food and
agricultural sector will ensure sustained and sufficient production of
food in Nigeria. Microfinance banks should make sufficient credit
available to smallholder farmer. Government should further control
and subsidize the rising price of food to make it more accessible by
the people.
Abstract: MHD chemically reacting viscous fluid flow towards
a vertical surface with slip and convective boundary conditions has
been conducted. The temperature and the chemical species
concentration of the surface and the velocity of the external flow are
assumed to vary linearly with the distance from the vertical surface.
The governing differential equations are modeled and transformed
into systems of ordinary differential equations, which are then solved
numerically by a shooting method. The effects of various parameters
on the heat and mass transfer characteristics are discussed. Graphical
results are presented for the velocity, temperature, and concentration
profiles whilst the skin-friction coefficient and the rate of heat and
mass transfers near the surface are presented in tables and discussed.
The results revealed that increasing the strength of the magnetic field
increases the skin-friction coefficient and the rate of heat and mass
transfers toward the surface. The velocity profiles are increased
towards the surface due to the presence of the Lorenz force, which
attracts the fluid particles near the surface. The rate of chemical
reaction is seen to decrease the concentration boundary layer near the
surface due to the destructive chemical reaction occurring near the
surface.
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: Elliptic curve discrete logarithm problem(ECDLP) is
one of problems on which the security of pairing-based cryptography
is based. This paper considers Pollard’s rho method to evaluate
the security of ECDLP on Barreto-Naehrig(BN) curve that is an
efficient pairing-friendly curve. Some techniques are proposed to
make the rho method efficient. Especially, the group structure on
BN curve, distinguished point method, and Montgomery trick are
well-known techniques. This paper applies these techniques and
shows its optimization. According to the experimental results for
which a large-scale parallel system with MySQL is applied, 94-bit
ECDLP was solved about 28 hours by parallelizing 71 computers.
Abstract: Two normal populations with different means and same
variance are considered, where the variance is known. The population
with the smaller sample mean is selected. Various estimators are
constructed for the mean of the selected normal population. Finally,
they are compared with respect to the bias and MSE risks by
the mehod of Monte-Carlo simulation and their performances are
analysed with the help of graphs.
Abstract: The influence of cultivation factors such as content of ammonium sulfate, glucose and water in the culture medium and particle size of dry orange waste, on their bioconversion for pectinase production was studied using complete factorial design. A polygalacturonase (PG) was isolated using ion exchange chromatography under gradient elution 0-0,5 m/l NaCl (column equilibrate with acetate buffer pH 4,5), subsequently by sephadex G75 column chromatography was applied and the molecular weight was obtained about 51,28 KDa. Purified PG enzyme exhibits a pH and temperature optima of activity at 5 and 35°C respectively. Treatment of apple juice by purified enzyme extract yielded a clear juice, which was competitive with juice yielded by pure Sigma Aldrich Aspergillus niger enzyme.
Abstract: Ecological systems are exposed and are influenced by
various natural and anthropogenic disturbances. They produce
various effects and states seeking response symmetry to a state of
global phase coherence or stability and balance of their food webs.
This research project addresses the development of a computational
methodology for modeling plankton food webs. The use of
algorithms to establish connections, the generation of representative
fuzzy multigraphs and application of technical analysis of complex
networks provide a set of tools for defining, analyzing and evaluating
community structure of coastal aquatic ecosystems, beyond the
estimate of possible external impacts to the networks. Thus, this
study aims to develop computational systems and data models to
assess how these ecological networks are structurally and
functionally organized, to analyze the types and degree of
compartmentalization and synchronization between oscillatory and
interconnected elements network and the influence of disturbances on
the overall pattern of rhythmicity of the system.
Abstract: Graphene was dispersed using a tip sonicator and the
effect of surfactants were analysed. Sodium Dodecyl Sulphate (SDS)
and Polyvinyl Alcohol (PVA) were compared to observe whether or
not they had any effect on any de-wrinkling, and secondly whether
they aided to achieve better dispersions. There is a huge demand for
wrinkle free graphene as this will greatly increase its usefulness in
various engineering applications. A comprehensive literature on dewrinkling
graphene has been discussed. Low magnification Scanning
Electronic Microscopy (SEM) was conducted to assess the quality of
graphene de-wrinkling. The utilization of the PVA has significant
effect on de-wrinkling whereas SDS had minimal effect on the dewrinkling
of graphene.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: This research paper presents the current practices of
teacher professional development, perceived as beneficial by teachers
themselves, in a private secondary school in Brunei Darussalam. This
is part of the findings of a larger qualitative study on teacher
empowerment, using ethnographic methods for data collection, i.e.
participant observation, interviews and document analysis. The field
work was carried out over a period of six months in 2013. An
analysis of the field data revealed multiple pathways of teacher
professional development existing in the school. The results indicate
that school leaders, the teacher community in the school, students,
and the teachers themselves were the agents in a school that
facilitated teacher empowerment. Besides contributing to the
knowledge base on teacher professional development, the results of
this study provide directions for educational policy makers in their
efforts to enhance professional development in secondary schools of
similar characteristics. For school leaders and the teacher community,
these findings offer guidelines for maximizing the opportunities for
these professional development practices, by strengthening
collegiality and by using the existing structures optimally for the
benefit of all concerned.
Abstract: Below-knee amputees commonly experience
asymmetrical gait patterns. It is generally believed that ischemia is
related to the formation of pressure sores due to uneven distribution
of forces. Micro-vascular responses can reveal local malnutrition.
Changes in local skin blood supply under various external loading
conditions have been studied for a number of years. Radionuclide
clearance, photo-plethysmography, trans-cutaneous oxygen tension
along with other studies showed that the blood supply would be
influenced by the epidermal forces, and the rate and the amount of
blood supply would decrease with increased epidermal loads being
shear forces or normal forces. Several cases of socket designs were
investigated using Finite Element Model (FEM) and Design of
Experiment (DOE) to increase flexibility and minimize the pressure
at the limb/socket interface using ultra high molecular weight
polyethylene (UHMWPE) and polyamide 6 (PA6) or Duraform. The
pressure reliefs at designated areas where reducing thickness is
involved are seen to be critical in determination of amputees’ comfort
and are very important to clinical applications. Implementing a hole
between the Patellar Tendon (PT) and Distal Tibia (DT) would
decrease stiffness and increase prosthesis range of motion where
flexibility is needed. In addition, displacement and prosthetic energy
storage increased without compromising mechanical efficiency and
prosthetic design integrity.
Abstract: The aim of this study is to investigate the relationship
between expectation, satisfaction and loyalty of South Korean
tourists visiting Turkey. In the research, a questionnaire was used as a
data collecting tool. The questionnaires are filled by South Korean
tourists coming to Turkey through package tours and individual. The
survey was conducted in 2014 in Nevsehir (Cappadocia Region) and
Istanbul. Tourist guides and agency staff have helped the
implementation of surveys. The survey questions are composed of 4
parts, which are “demographic characteristics of tourists”, “travel
behavior characteristics”, “perception of expectations on destination
attributes” and “perception of destination loyalty”. 5-point Likert
type scale including 28 destination attributes was used to measure the
expectations of South Korean tourists coming to Turkey. Questions
were directed to the tourists to measure the destination loyalty. The
questions relating to destination loyalty are “Talking about Turkey to
others”, “Recommendation Turkey to others” and “Tourists’
intentions to revisit Turkey”. The basic hypothesis of the research is
that there is a statistically significant relationship among
expectations, satisfactions and destination loyalty of South Korean
tourists coming to Turkey. The results indicated that the expectation
had a significant effect on overall satisfaction. In addition it was seen
that between overall satisfaction of tourists and destination loyalty
had a significant relationship. Based on findings, some suggestions
for tour operators and travel agencies were made.
Abstract: Computer aided diagnosis systems provide vital
opinion to radiologists in the detection of early signs of breast cancer
from mammogram images. Architectural distortions, masses and
microcalcifications are the major abnormalities. In this paper, a
computer aided diagnosis system has been proposed for
distinguishing abnormal mammograms with architectural distortion
from normal mammogram. Four types of texture features GLCM
texture, GLRLM texture, fractal texture and spectral texture features
for the regions of suspicion are extracted. Support vector machine
has been used as classifier in this study. The proposed system yielded
an overall sensitivity of 96.47% and an accuracy of 96% for
mammogram images collected from digital database for screening
mammography database.
Abstract: Batch production plants provide a wide range of
scheduling problems. In pharmaceutical industries a batch process
is usually described by a recipe, consisting of an ordering of tasks
to produce the desired product. In this research work we focused
on pharmaceutical production processes requiring the culture of
a microorganism population (i.e. bacteria, yeasts or antibiotics).
Several sources of uncertainty may influence the yield of the culture
processes, including (i) low performance and quality of the cultured
microorganism population or (ii) microbial contamination. For
these reasons, robustness is a valuable property for the considered
application context. In particular, a robust schedule will not collapse
immediately when a cell of microorganisms has to be thrown away
due to a microbial contamination. Indeed, a robust schedule should
change locally in small proportions and the overall performance
measure (i.e. makespan, lateness) should change a little if at all.
In this research work we formulated a constraint programming
optimization (COP) model for the robust planning of antibiotics
production. We developed a discrete-time model with a multi-criteria
objective, ordering the different criteria and performing a
lexicographic optimization. A feasible solution of the proposed
COP model is a schedule of a given set of tasks onto available
resources. The schedule has to satisfy tasks precedence constraints,
resource capacity constraints and time constraints. In particular
time constraints model tasks duedates and resource availability
time windows constraints. To improve the schedule robustness, we
modeled the concept of (a, b) super-solutions, where (a, b) are input
parameters of the COP model. An (a, b) super-solution is one in
which if a variables (i.e. the completion times of a culture tasks)
lose their values (i.e. cultures are contaminated), the solution can be
repaired by assigning these variables values with a new values (i.e.
the completion times of a backup culture tasks) and at most b other
variables (i.e. delaying the completion of at most b other tasks).
The efficiency and applicability of the proposed model is
demonstrated by solving instances taken from a real-life
pharmaceutical company. Computational results showed that
the determined super-solutions are near-optimal.