Abstract: In this paper an algorithm based on the adaptive
neuro-fuzzy controller is provided to enhance the tipover stability of
mobile manipulators when they are subjected to predefined
trajectories for the end-effector and the vehicle. The controller
creates proper configurations for the manipulator to prevent the robot
from being overturned. The optimal configuration and thus the most
favorable control are obtained through soft computing approaches
including a combination of genetic algorithm, neural networks, and
fuzzy logic. The proposed algorithm, in this paper, is that a look-up
table is designed by employing the obtained values from the genetic
algorithm in order to minimize the performance index and by using
this data base, rule bases are designed for the ANFIS controller and
will be exerted on the actuators to enhance the tipover stability of the
mobile manipulator. A numerical example is presented to
demonstrate the effectiveness of the proposed algorithm.
Abstract: In this paper, linear multistep technique using power
series as the basis function is used to develop the block methods
which are suitable for generating direct solution of the special second
order ordinary differential equations with associated initial or
boundary conditions. The continuous hybrid formulations enable us
to differentiate and evaluate at some grids and off – grid points to
obtain two different four discrete schemes, each of order (5,5,5,5)T,
which were used in block form for parallel or sequential solutions of
the problems. The computational burden and computer time wastage
involved in the usual reduction of second order problem into system
of first order equations are avoided by this approach. Furthermore, a
stability analysis and efficiency of the block methods are tested on
linear and non-linear ordinary differential equations and the results
obtained compared favorably with the exact solution.
Abstract: The Marangoni convective instability in a horizontal
fluid layer with the insoluble surfactant and nondeformable free
surface is investigated. The surface tension at the free surface is
linearly dependent on the temperature and concentration gradients.
At the bottom surface, the temperature conditions of uniform
temperature and uniform heat flux are considered. By linear stability
theory, the exact analytical solutions for the steady Marangoni
convection are derived and the marginal curves are plotted. The
effects of surfactant or elasticity number, Lewis number and Biot
number on the marginal Marangoni instability are assessed. The
surfactant concentration gradients and the heat transfer mechanism at
the free surface have stabilizing effects while the Lewis number
destabilizes fluid system. The fluid system with uniform temperature
condition at the bottom boundary is more stable than the fluid layer
that is subjected to uniform heat flux at the bottom boundary.
Abstract: In this paper, the problem of asymptotical stability of neutral systems with nonlinear perturbations is investigated. Based on a class of novel augment Lyapunov functionals which contain freeweighting matrices, some new delay-dependent asymptotical stability criteria are formulated in terms of linear matrix inequalities (LMIs) by using new inequality analysis technique. Numerical examples are given to demonstrate the derived condition are much less conservative than those given in the literature.
Abstract: Power System Security is a major concern in real time
operation. Conventional method of security evaluation consists of
performing continuous load flow and transient stability studies by
simulation program. This is highly time consuming and infeasible
for on-line application. Pattern Recognition (PR) is a promising
tool for on-line security evaluation. This paper proposes a Support
Vector Machine (SVM) based binary classification for static and
transient security evaluation. The proposed SVM based PR approach
is implemented on New England 39 Bus and IEEE 57 Bus systems.
The simulation results of SVM classifier is compared with the other
classifier algorithms like Method of Least Squares (MLS), Multi-
Layer Perceptron (MLP) and Linear Discriminant Analysis (LDA)
classifiers.
Abstract: Biplot can be used to evaluate cultivars for their oil
percent potential and stability and to evaluate trial sites for their
discriminating ability and representativeness. Multi-environmental
trial (MET) data for oil percent of 10 open pollinating sunflower
cultivars were analyzed to investigate the genotype-environment
interactions. The genotypes were evaluated in four locations with
different climatic conditions in Iran in 2010. In each location, a
Randomized Complete Block design with four replications was used.
According to both mean and stability, Zaria, Master and R453, had
highest performances among all cultivars. The graphical analysis
identified best cultivar for each environment. Cultivars Berezans and
Record performed best in Khoy and Islamabad. Zaria and R453 were
the best genotypes in Sari and Karaj followed by Master and Favorit.
The GGE bi-plot indicated two mega-environments, group one
contained Karaj, Khoy and Islamabad and the second group
contained Sari. The best discriminating location was Karaj followed
with Khoy, Islamabad and Sari. The best representative genotypes
were Zaria, R453, Master and Favorit. Ranking of ten cultivars based
their oil percent was as Zaria > R453 ≈ Master ≈ Favorit > Record ≈
Berezans > Sor > Lakumka > Bulg3 > Bulg5.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: IFP Group Technology “Sulfrex process" was used in
Iran-s South Pars Gas Complex Refineries for removing sulfur
compounds such as mercaptans, carbonyl sulfide and hydrogen
sulfide, which uses sulfonated cobalt phthalocyanine dispersed in
alkaline solution as catalyst. In this technology, catalyst and alkaline
solution were used circularly. However the stability of catalyst due to
effect of some parameters would reduce with the running of the unit
and therefore sweetening efficiency would be decreased. Hence, the
aim of this research is study the factors effecting on the stability of
catalyst.
Abstract: This paper presents how the real-time chatter
prevention can be realized by feedback of acoustic cutting signal, and
the efficacy of the proposed adaptive spindle speed tuning algorithm is
verified by intensive experimental simulations. A pair of
microphones, perpendicular to each other, is used to acquire the
acoustic cutting signal resulting from milling chatter. A real-time
feedback control loop is constructed for spindle speed compensation
so that the milling process can be ensured to be within the stability
zone of stability lobe diagram. Acoustic Chatter Signal Index (ACSI)
and Spindle Speed Compensation Strategy (SSCS) are proposed to
quantify the acoustic signal and actively tune the spindle speed
respectively. By converting the acoustic feedback signal into ACSI,
an appropriate Spindle Speed Compensation Rate (SSCR) can be
determined by SSCS based on real-time chatter level or ACSI.
Accordingly, the compensation command, referred to as Added-On
Voltage (AOV), is applied to increase/decrease the spindle motor
speed. By inspection on the precision and quality of the workpiece
surface after milling, the efficacy of the real-time chatter prevention
strategy via acoustic signal feedback is further assured.
Abstract: We investigate the ZnO role in the inherent protection
of old manuscripts to protect them against environmental damaging
effect of ultraviolet radiation, pollutant gasses, mold and bacteria. In
this study a cellulosic nanocomposite of ZnO were used as protective
coating on the surface of paper fibers. This layered nanocomposite
can act as a consolidate materials too. Furthermore, to determine how
well paper works screen objects from the damaging effects, two
accelerated aging mechanisms due to light and heat are discussed.
Results show good stability of papers with nanocomposite coating.
Also, a good light stability was shown in the colored paper that
treated with this nanocomposite. Furthermore, to demonstrate the
degree of antifungal and antibacterial properties of coated papers,
papers was treated with four common molds and bacteria and the
good preventive effects of coated paper against molds and bacteria
are described.
Abstract: Reversible logic is becoming more and more prominent
as the technology sets higher demands on heat, power, scaling
and stability. Reversible gates are able at any time to "undo" the
current step or function. Multiple-valued logic has the advantage of
transporting and evaluating higher bits each clock cycle than binary.
Moreover, we demonstrate in this paper, combining these disciplines
we can construct powerful multiple-valued reversible logic structures.
In this paper a reversible block implemented by pseudo floatinggate
can perform AD-function and a DA-function as its reverse
application.
Abstract: Electricity market activities and a growing demand for electricity have led to heavily stressed power systems. This requires operation of the networks closer to their stability limits. Power system operation is affected by stability related problems, leading to unpredictable system behavior. Voltage stability refers to the ability of a power system to sustain appropriate voltage levels through large and small disturbances. Steady-state voltage stability is concerned with limits on the existence of steady-state operating points for the network. FACTS devices can be utilized to increase the transmission capacity, the stability margin and dynamic behavior or serve to ensure improved power quality. Their main capabilities are reactive power compensation, voltage control and power flow control. Among the FACTS controllers, Static Var Compensator (SVC) provides fast acting dynamic reactive compensation for voltage support during contingency events. In this paper, voltage stability assessment with appropriate representations of tap-changer transformers and SVC is investigated. Integrating both of these devices is the main topic of this paper. Effect of the presence of tap-changing transformers on static VAR compensator controller parameters and ratings necessary to stabilize load voltages at certain values are highlighted. The interrelation between transformer off nominal tap ratios and the SVC controller gains and droop slopes and the SVC rating are found. P-V curves are constructed to calculate loadability margins.
Abstract: A variational method is used to obtain the growth rate of a transverse long-wavelength perturbation applied to the soliton solution of a nonlinear Schr¨odinger equation with a three-half order potential. We demonstrate numerically that this unstable perturbed soliton will eventually transform into a cylindrical soliton.
Abstract: A logic model for analyzing complex systems- stability
is very useful to many areas of sciences. In the real world, we are
enlightened from some natural phenomena such as “biosphere", “food
chain", “ecological balance" etc. By research and practice, and taking
advantage of the orthogonality and symmetry defined by the theory of
multilateral matrices, we put forward a logic analysis model of
stability of complex systems with three relations, and prove it by
means of mathematics. This logic model is usually successful in
analyzing stability of a complex system. The structure of the logic
model is not only clear and simple, but also can be easily used to
research and solve many stability problems of complex systems. As an
application, some examples are given.
Abstract: We have fabricated a-IGZO TFT and investigated the
stability under positive DC and AC bias stress. The threshold voltage
of a-IGZO TFT shifts positively under those biases, and that reduces
on-current. For this reason, conventional shift-register circuit
employing TFTs which stressed by positive bias will be unstable, may
do not work properly. We have designed a new 6-transistor
shift-register, which has less transistors than prior circuits. The TFTs
of the proposed shift-register are not suffering from positive DC or AC
stress, mainly kept unbiased. Despite the compact design, the stable
output signal was verified through the SPICE simulation even under
RC delay of clock signal.
Abstract: The objective of the research was to evaluate the
hardness stability of milk pomade sweets packed in several
packaging materials (OPP, Multibarrier 60 HFP, BIALON 65
HFP, BIALON 50 HFP, ECOLEAN) by several packaging
technologies – modified atmosphere (MAP) (consisting of
30% CO2+70% N2; 30% N2+70% CO2 and 100% CO2) and
control – in air ambiance. Samples were stored at the room
temperature +21±1 °C. The studies of the samples were
carried out before packaging and after 2, 4, 6, 8, and 10
storage weeks.
Abstract: The corrugated steel cladding used to cover most of
steel buildings is considered as non-structural element. This research
will reflect the effect of cladding as a shear diaphragm in increasing
the normal elastic capacity of columns. This study is important
because of the lack of information of the behavior of cladding and
secondary members in various codes. Mathematical models for six
different cases are carried by software. The results extracted from the
program have been plotted showing the effects of different variables
on the ultimate load of column. The variables considered in our
research are the spacing between columns and the thickness of the
corrugated sheet representing the sheet stiffness.
Abstract: In this paper, by using Mawhin-s continuation theorem of coincidence degree and a method based on delay differential inequality, some sufficient conditions are obtained for the existence and global exponential stability of periodic solutions of cellular neural networks with distributed delays and impulses on time scales. The results of this paper generalized previously known results.
Abstract: The problem of controlling a two link robotic manipulator, consisting of a rotating and a prismatic links, is addressed. The actuations of both links are assumed to have unknown dead zone nonlinearities and friction torques modeled by LuGre friction model. Because of the existence of the unknown dead zone and friction torque at the actuations, unknown parameters and unmeasured states would appear to be part of the overall system dynamics that need for estimation. Unmeasured states observer, unknown parameters estimators, and robust adaptive control laws have been derived such that closed loop global stability is achieved. Simulation results have been performed to show the efficacy of the suggested approach.
Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.