Abstract: Reinforced concrete crash barriers used in road traffic
must meet a number of criteria. Crash barriers are laid lengthwise,
one behind another, and joined using specially designed steel locks.
While developing BSV reinforced concrete crash barriers (type
ŽPSV), experiments and calculations aimed to optimize the shape of
a newly designed lock and the reinforcement quantity and
distribution in a crash barrier were carried out. The tension carrying
capacity of two parallelly joined locks was solved experimentally.
Based on the performed experiments, adjustments of nonlinear
properties of steel were performed in the calculations. The obtained
results served as a basis to optimize the lock design using a
computational model that takes into account the plastic behaviour of
steel and the influence of the surrounding concrete [6]. The response
to the vehicle impact has been analyzed using a specially elaborated
complex computational model, comprising both the nonlinear model
of the damping wall or crash barrier and the detailed model of the
vehicle [7].
Abstract: A pilot project was carried out in 2007 by the senior
students of Cyprus International University, aiming to minimize the
total cost of waste collection in Northern Cyprus. Many developed
and developing countries have cut their transportation costs – which
lies between 30-40% – down at a rate of 40% percent, by
implementing network models for their route assignments.
Accordingly, a network model was implemented at Göçmenköy
district, to optimize and standardize waste collection works. The
work environment of the employees were also redesigned to provide
maximum ergonomy and to increase productivity, efficiency and
safety. Following the collection of the required data including waste
densities, lengths of roads and population, a model was constructed
to allocate the optimal route assignment for the waste collection
trucks at Göçmenköy district.
Abstract: Energy consumption is one of the indices in
determining the levels of development of a nation. Therefore,
availability of energy supply to all sectors of life in any country is
crucial for its development. These exists shortage of all kinds of
energy, particularly electricity which is badly needed for economic
development. Electricity from the sun which is quite abundant in
most of the developing countries is used in rural areas to meet basic
electricity needs of a rural community. Today-s electricity supply in
Myanmar is generated by fuel generators and hydroelectric power
plants. However, far-flung areas which are away from National Grids
cannot enjoy the electricity generated by these sources. Since
Myanmar is a land of plentiful sunshine, especially in central and
southern regions of the country, the first form of energy- solar energy
could hopefully become the final solution to its energy supply
problem. The direct conversion of solar energy into electricity using
photovoltaic system has been receiving intensive installation not only
in developed countries but also in developing countries. It is mainly
intended to present solar energy potential and application in
Myanmar. It is also wanted to get the benefits of using solar energy
for people in remote areas which are not yet connected to the national
grids because of the high price of fossil fuel.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: As an effort to promote wind power industry in Korea,
Korea South-East Power Corporation has been developing 22MW
YeungHeung wind farm consisting of nine 2 to 3MW wind turbines
supplied by three manufacturers. To maximize its availability and
reliability and to solve the difficulty of operating three kinds of
SCADA systems, Korea Electric Power Corporation has been
developing a condition monitoring system integrated with control
functions. This paper presents the developed condition monitoring
system and its application to YeungHeung wind test bed, and the
design of its control functions.
Abstract: This paper presents a research agenda on the SCOR
model adaptation. SCOR model is designated to measure supply
chain performance and logistics impact across the boundaries of
individual organizations. It is at its growing stage of its life cycle and
is enjoying the leverage of becoming the industry standard. The
SCOR model has been developed and used widely in developed
countries context. This research focuses on the SCOR model
adaptation for the manufacturing industry in developing countries.
With a necessary understanding of the characteristics, difficulties and
problems of the manufacturing industry in developing countries-
supply chain; consequently, we will try to designs an adapted model
with its building blocks: business process model, performance
measures and best practices.
Abstract: MANEMO is the integration of Network Mobility
(NEMO) and Mobile Ad Hoc Network (MANET). A MANEMO
node has an interface to both a MANET and NEMO network, and
therefore should choose the optimal interface for packet delivery,
however such a handover between interfaces will introduce packet
loss. We define the steps necessary for a MANEMO handover,
using Mobile IP and NEMO to signal the new binding to the
relevant Home Agent(s). The handover steps aim to minimize the
packet loss by avoiding waiting for Duplicate Address Detection
and Neighbour Unreachability Detection. We present expressions for
handover delay and packet loss, and then use numerical examples to
evaluate a MANEMO handover. The analysis shows how the packet
loss depends on level of nesting within NEMO, the delay between
Home Agents and the load on the MANET, and hence can be used
to developing optimal MANEMO handover algorithms.
Abstract: With the demand of mobility by users, wireless
technologies have become the hotspot developing arena. Internet
Engineering Task Force (IETF) working group has developed Mobile
IP to support node mobility. The concept of node mobility indicates
that in spite of the movement of the node, it is still connected to the
internet and all the data transactions are preserved. It provides
location-independent access to Internet. After the incorporation of
host mobility, network mobility has undergone intense research.
There are several intricacies faced in the real world implementation
of network mobility significantly the problem of nested networks and
their consequences. This article is concerned regarding a problem of
nested network called pinball route problem and proposes a solution
to eliminate the above problem. The proposed mechanism is
implemented using NS2 simulation tool and it is found that the
proposed mechanism efficiently reduces the overload caused by the
pinball route problem.
Abstract: Medical services are usually provided in hospitals; however, in developing country, some rural residences have fewer opportunities to access in healthcare services due to the limitation of transportation communication. Therefore, in Thailand, there are charitable organizations operating to provide medical treatments to these people by shifting the medical services to operation sites; this is commonly known as mobile medical service. Operation routing is important for the organization to reduce its transportation cost in order to focus more on other important activities; for instance, the development of medical apparatus. VRP is applied to solve the problem of high transportation cost of the studied organization with the searching techniques of saving algorithm to find the minimum total distance of operation route and satisfy available time constraints of voluntary medical staffs.
Abstract: The development and use of mobile devices as well as its integration within education systems to deliver electronic contents and to support real-time communications was the focus of this research. In order to investigate the software engineering issues in using mobile devices a research on electronic content was initiated. The Developed MP3 mobile software solution was developed as a prototype for testing and developing a strategy for designing a usable m-learning environment. The mobile software solution was evaluated using mobile device using the link: http://projects.seeu.edu.mk/mlearn. The investigation also tested the correlation between the two mobile learning indicators: electronic content and attention, based on the Task Based learning instructional method. The mobile software solution ''M-Learn“ was developed as a prototype for testing the approach and developing a strategy for designing usable m-learning environment. The proposed methodology is about what learning modeling approach is more appropriate to use when developing mobile learning software.
Abstract: Road authorities have confronted problems to
maintaining the serviceability of road infrastructure systems by using
various traditional methods of contracting. As a solution to these
problems, many road authorities have started contracting out road
maintenance works to the private sector based on performance
measures. This contracting method is named Performance-Based
Maintenance Contracting (PBMC). It is considered more costeffective
than other traditional methods of contracting. It has a
substantial success records in many developed and developing
countries over the last two decades. This paper discusses and
analyses the potential issues to be considered before the introduction
of PBMC in a country.
Abstract: Since 2004, we have been developing an in-situ storage image sensor (ISIS) that captures more than 100 consecutive images at a frame rate of 10 Mfps with ultra-high sensitivity as well as the video camera for use with this ISIS. Currently, basic research is continuing in an attempt to increase the frame rate up to 100 Mfps and above. In order to suppress electro-magnetic noise at such high frequency, a digital-noiseless imaging transfer scheme has been developed utilizing solely sinusoidal driving voltages. This paper presents highly efficient-yet-accurate expressions to estimate attenuation as well as phase delay of driving voltages through RC networks of an ultra-high-speed image sensor. Elmore metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE data, we found a simple expression that significantly improves the accuracy of the approximation. Similarly, another simple closed-form model to estimate phase delay through fundamental RC networks is also obtained. Estimation error of both expressions is much less than previous works, only less 2% for most of the cases . The framework of this analysis can be extended to address similar issues of other VLSI structures.
Abstract: In this paper, algorithms for the automatic localisation
of two anatomical soft tissue landmarks of the head the medial
canthus (inner corner of the eye) and the tragus (a small, pointed,
cartilaginous flap of the ear), in CT images are describet. These
landmarks are to be used as a basis for an automated image-to-patient
registration system we are developing. The landmarks are localised
on a surface model extracted from CT images, based on surface
curvature and a rule based system that incorporates prior knowledge
of the landmark characteristics. The approach was tested on a dataset
of near isotropic CT images of 95 patients. The position of the
automatically localised landmarks was compared to the position of
the manually localised landmarks. The average difference was 1.5
mm and 0.8 mm for the medial canthus and tragus, with a maximum
difference of 4.5 mm and 2.6 mm respectively.The medial canthus
and tragus can be automatically localised in CT images, with
performance comparable to manual localisation
Abstract: Ability of accurate and reliable location estimation in
indoor environment is the key issue in developing great number of
context aware applications and Location Based Services (LBS).
Today, the most viable solution for localization is the Received
Signal Strength (RSS) fingerprinting based approach using wireless
local area network (WLAN). This paper presents two RSS
fingerprinting based approaches – first we employ widely used
WLAN based positioning as a reference system and then investigate
the possibility of using GSM signals for positioning. To compare
them, we developed a positioning system in real world environment,
where realistic RSS measurements were collected. Multi-Layer
Perceptron (MLP) neural network was used as the approximation
function that maps RSS fingerprints and locations. Experimental
results indicate advantage of WLAN based approach in the sense of
lower localization error compared to GSM based approach, but GSM
signal coverage by far outreaches WLAN coverage and for some
LBS services requiring less precise accuracy our results indicate that
GSM positioning can also be a viable solution.
Abstract: Relevant agricultural information disseminator
(extension agent) ratio of 1:3500 farm families which become a
menace to agricultural production capacity in developing countries
necessitate this study. Out of 4 zones in the state, 24 extension agents
in each zone, 4 extension agents using cell phones and 120 farmers
using cell phone and 120 other farmers not using cell phone were
purposively selected to give 240 farmers that participated in the
research. Data were collected using interview guide and analysized
using frequency, percentage and t-test.. Frequency of contact with
agricultural information centers revealed that cell phone user farmers
had greater means score of X 41.43 contact as against the low mean
X19.32 contact recorded by farmers receiving agricultural
information from extension agents not using cell phone and their
production was statistically significant at P < 0.05. Usage of cell
phone increase extension agent contact and increase farmers-
production capacity.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: This paper presents a solution for the behavioural animation of autonomous virtual agent navigation in virtual environments. We focus on using Dempster-Shafer-s Theory of Evidence in developing visual sensor for virtual agent. The role of the visual sensor is to capture the information about the virtual environment or identifie which part of an obstacle can be seen from the position of the virtual agent. This information is require for vitual agent to coordinate navigation in virtual environment. The virual agent uses fuzzy controller as a navigation system and Fuzzy α - level for the action selection method. The result clearly demonstrates the path produced is reasonably smooth even though there is some sharp turn and also still not diverted too far from the potential shortest path. This had indicated the benefit of our method, where more reliable and accurate paths produced during navigation task.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: Human perceives color in categories, which may be
identified using color name such as red, blue, etc. The categorization
is unique for each human being. However despite the individual
differences, the categorization is shared among members in society.
This allows communication among them, especially when using
color name. Sociable robot, to live coexist with human and become
part of human society, must also have the shared color
categorization, which can be achieved through learning. Many
works have been done to enable computer, as brain of robot, to learn
color categorization. Most of them rely on modeling of human color
perception and mathematical complexities. Differently, in this work,
the computer learns color categorization through interaction with
humans. This work aims at developing the innate ability of the
computer to learn the human-like color categorization. It focuses on
the representation of color categorization and how it is built and
developed without much mathematical complexity.