Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: Medical image modalities such as computed
tomography (CT), magnetic resonance imaging (MRI), ultrasound
(US), X-ray are adapted to diagnose disease. These modalities
provide flexible means of reviewing anatomical cross-sections and
physiological state in different parts of the human body. The raw
medical images have a huge file size and need large storage
requirements. So it should be such a way to reduce the size of those
image files to be valid for telemedicine applications. Thus the image
compression is a key factor to reduce the bit rate for transmission or
storage while maintaining an acceptable reproduction quality, but it is
natural to rise the question of how much an image can be compressed
and still preserve sufficient information for a given clinical
application. Many techniques for achieving data compression have
been introduced. In this study, three different MRI modalities which
are Brain, Spine and Knee have been compressed and reconstructed
using wavelet transform. Subjective and objective evaluation has
been done to investigate the clinical information quality of the
compressed images. For the objective evaluation, the results show
that the PSNR which indicates the quality of the reconstructed image
is ranging from (21.95 dB to 30.80 dB, 27.25 dB to 35.75 dB, and
26.93 dB to 34.93 dB) for Brain, Spine, and Knee respectively. For
the subjective evaluation test, the results show that the compression
ratio of 40:1 was acceptable for brain image, whereas for spine and
knee images 50:1 was acceptable.
Abstract: wind catchers have been served as a cooling system, used to provide acceptable ventilation by means of renewable energy of wind. In the present study, the city of Yazd in arid climate is selected as case study. From the architecture point of view, learning about wind catchers in this study is done by means of field surveys. Research method for selection of the case is based on random form, and analytical method. Wind catcher typology and knowledge of relationship governing the wind catcher's architecture were those measures that are taken for the first time. 53 wind catchers were analyzed. The typology of the wind-catchers is done by the physical analyzing, patterns and common concepts as incorporated in them. How the architecture of wind catcher can influence their operations by analyzing thermal behavior are the archetypes of selected wind catchers. Calculating fluids dynamics science, fluent software and numerical analysis are used in this study as the most accurate analytical approach. The results obtained from these analyses show the formal specifications of wind catchers with optimum operation in Yazd. The knowledge obtained from the optimum model could be used for design and construction of wind catchers with more improved operation
Abstract: It has become crucial over the years for nations to
improve their credit scoring methods and techniques in light of the
increasing volatility of the global economy. Statistical methods or
tools have been the favoured means for this; however artificial
intelligence or soft computing based techniques are becoming
increasingly preferred due to their proficient and precise nature and
relative simplicity. This work presents a comparison between Support
Vector Machines and Artificial Neural Networks two popular soft
computing models when applied to credit scoring. Amidst the
different criteria-s that can be used for comparisons; accuracy,
computational complexity and processing times are the selected
criteria used to evaluate both models. Furthermore the German credit
scoring dataset which is a real world dataset is used to train and test
both developed models. Experimental results obtained from our study
suggest that although both soft computing models could be used with
a high degree of accuracy, Artificial Neural Networks deliver better
results than Support Vector Machines.
Abstract: Within the realm of e-government, the development has moved towards testing new means for democratic decisionmaking, like e-panels, electronic discussion forums, and polls. Although such new developments seem promising, they are not problem-free, and the outcomes are seldom used in the subsequent formal political procedures. Nevertheless, process models offer promising potential when it comes to structuring and supporting transparency of decision processes in order to facilitate the integration of the public into decision-making procedures in a reasonable and manageable way. Based on real-life cases of urban planning processes in Sweden, we present an outline for an integrated framework for public decision making to: a) provide tools for citizens to organize discussion and create opinions; b) enable governments, authorities, and institutions to better analyse these opinions; and c) enable governments to account for this information in planning and societal decision making by employing a process model for structured public decision making.
Abstract: One of the basic concepts in marketing is the concept
of meeting customers- needs. Since customer satisfaction is essential
for lasting survival and development of a business, screening and
observing customer satisfaction and recognizing its underlying
factors must be one of the key activities of every business.
The purpose of this study is to recognize the drivers that effect
customer satisfaction in a business-to-business situation in order to
improve marketing activities. We conducted a survey in which 93
business customers of a manufacturer of Diesel Generator in Iran
participated and they talked about their ideas and satisfaction of
supplier-s services related to its products. We developed the measures
for drivers of satisfaction first by as investigative research (by means
of feedback from executives and customers of sponsoring firm). Then
based on these measures, we created a mail survey, and asked the
respondents to explain their opinion about the sponsoring firm which
was a supplier of diesel generator and similar products. Furthermore,
the survey required the participants to mention their functional areas
and their company features.
In Conclusion we found that there are three drivers for customer
satisfaction, which are reliability, information about product, and
commercial features. Buyers/users from different functional areas
attribute different degree of importance to the last two drivers. For
instance, people from buying and management areas believe that
commercial features are more important than information about
products. But people in engineering, maintenance and production
areas believe that having information about products is more
important than commercial aspects. Marketing experts should
consider the attribute of customers regarding information about the
product and commercial features to improve market share.
Abstract: An important step in three-dimensional reconstruction
and computer vision is camera calibration, whose objective is to
estimate the intrinsic and extrinsic parameters of each camera. In this
paper, two linear methods based on the different planes are given. In
both methods, the general plane is used to replace the calibration
object with very good precision. In the first method, after controlling
the camera to undergo five times- translation movements and taking
pictures of the orthogonal planes, a set of linear constraints of the
camera intrinsic parameters is then derived by means of homography
matrix. The second method is to get all camera parameters by taking
only one picture of a given radius circle. experiments on simulated
data and real images,indicate that our method is reasonable and is a
good supplement to camera calibration.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.
Abstract: In technological processes, in addition to the main
product, result a large amount of materials, called wastes, but due to
the possibilities of recovery, by means of recycling and reusing it can
fit in the category of by-products. These large amounts of dust from
the steel industry are a major problem in terms of environmental and
human health, landscape, etc. Solving these problems, the impressive
amounts of waste can be done through their proper management and
recovery for every type of waste. In this article it was watched the
capitalizing through pelleting and briquetting of small and powdery
waste aiming to obtain the sponge iron as raw material, used in blast
furnaces and electric arc furnaces. The data have been processed in
the Excel spreadsheet program, being presented in the form of
diagrams.
Abstract: The development of Artificial Neural Networks
(ANNs) is usually a slow process in which the human expert has to
test several architectures until he finds the one that achieves best
results to solve a certain problem. This work presents a new
technique that uses Genetic Programming (GP) for automatically
generating ANNs. To do this, the GP algorithm had to be changed in
order to work with graph structures, so ANNs can be developed. This
technique also allows the obtaining of simplified networks that solve
the problem with a small group of neurons. In order to measure the
performance of the system and to compare the results with other
ANN development methods by means of Evolutionary Computation
(EC) techniques, several tests were performed with problems based
on some of the most used test databases. The results of those
comparisons show that the system achieves good results comparable
with the already existing techniques and, in most of the cases, they
worked better than those techniques.
Abstract: Segmenting the lungs in medical images is a
challenging and important task for many applications. In particular,
automatic segmentation of lung cavities from multiple magnetic
resonance (MR) images is very useful for oncological applications
such as radiotherapy treatment planning. However, distinguishing of
the lung areas is not trivial due to largely changing lung shapes, low
contrast and poorly defined boundaries. In this paper, we address
lung segmentation problem from pulmonary magnetic resonance
images and propose an automated method based on a robust regionaided
geometric snake with a modified diffused region force into the
standard geometric model definition. The extra region force gives the
snake a global complementary view of the lung boundary
information within the image which along with the local gradient
flow, helps detect fuzzy boundaries. The proposed method has been
successful in segmenting the lungs in every slice of 30 magnetic
resonance images with 80 consecutive slices in each image. We
present results by comparing our automatic method to manually
segmented lung cavities provided by an expert radiologist and with
those of previous works, showing encouraging results and high
robustness of our approach.
Abstract: Biological sequences from different species are called or-thologs if they evolved from a sequence of a common ancestor species and they have the same biological function. Approximations of Kolmogorov complexity or entropy of biological sequences are already well known to be useful in extracting similarity information between such sequences -in the interest, for example, of ortholog detection. As is well known, the exact Kolmogorov complexity is not algorithmically computable. In prac-tice one can approximate it by computable compression methods. How-ever, such compression methods do not provide a good approximation to Kolmogorov complexity for short sequences. Herein is suggested a new ap-proach to overcome the problem that compression approximations may notwork well on short sequences. This approach is inspired by new, conditional computations of Kolmogorov entropy. A main contribution of the empir-ical work described shows the new set of entropy-based machine learning attributes provides good separation between positive (ortholog) and nega-tive (non-ortholog) data - better than with good, previously known alter-natives (which do not employ some means to handle short sequences well).Also empirically compared are the new entropy based attribute set and a number of other, more standard similarity attributes sets commonly used in genomic analysis. The various similarity attributes are evaluated by cross validation, through boosted decision tree induction C5.0, and by Receiver Operating Characteristic (ROC) analysis. The results point to the conclu-sion: the new, entropy based attribute set by itself is not the one giving the best prediction; however, it is the best attribute set for use in improving the other, standard attribute sets when conjoined with them.
Abstract: In this paper, the two-dimensional reversed stagnationpoint
flow is solved by means of an anlytic approach. There are
similarity solutions in case the similarity equation and the boundary
condition are modified. Finite analytic method are applied to obtain
the similarity velocity function.
Abstract: The understanding of the system level of biological behavior and phenomenon variously needs some elements such as gene sequence, protein structure, gene functions and metabolic pathways. Challenging problems are representing, learning and reasoning about these biochemical reactions, gene and protein structure, genotype and relation between the phenotype, and expression system on those interactions. The goal of our work is to understand the behaviors of the interactions networks and to model their evolution in time and in space. We propose in this study an ontological meta-model for the knowledge representation of the genetic regulatory networks. Ontology in artificial intelligence means the fundamental categories and relations that provide a framework for knowledge models. Domain ontology's are now commonly used to enable heterogeneous information resources, such as knowledge-based systems, to communicate with each other. The interest of our model is to represent the spatial, temporal and spatio-temporal knowledge. We validated our propositions in the genetic regulatory network of the Aarbidosis thaliana flower
Abstract: In Data mining, Fuzzy clustering algorithms have
demonstrated advantage over crisp clustering algorithms in dealing
with the challenges posed by large collections of vague and uncertain
natural data. This paper reviews concept of fuzzy logic and fuzzy
clustering. The classical fuzzy c-means algorithm is presented and its
limitations are highlighted. Based on the study of the fuzzy c-means
algorithm and its extensions, we propose a modification to the cmeans
algorithm to overcome the limitations of it in calculating the
new cluster centers and in finding the membership values with
natural data. The efficiency of the new modified method is
demonstrated on real data collected for Bhutan-s Gross National
Happiness (GNH) program.
Abstract: Segmentation of Magnetic Resonance Imaging (MRI) images is the most challenging problems in medical imaging. This paper compares the performances of Seed-Based Region Growing (SBRG), Adaptive Network-Based Fuzzy Inference System (ANFIS) and Fuzzy c-Means (FCM) in brain abnormalities segmentation. Controlled experimental data is used, which designed in such a way that prior knowledge of the size of the abnormalities are known. This is done by cutting various sizes of abnormalities and pasting it onto normal brain tissues. The normal tissues or the background are divided into three different categories. The segmentation is done with fifty seven data of each category. The knowledge of the size of the abnormalities by the number of pixels are then compared with segmentation results of three techniques proposed. It was proven that the ANFIS returns the best segmentation performances in light abnormalities, whereas the SBRG on the other hand performed well in dark abnormalities segmentation.
Abstract: Modes of occurrence of Pb, As, Cr, Co, Cu, and Ni in bituminous coal and lignite were determined by means of sequential extraction using NH4OAc, HCl, HF and HNO3 extraction solutions. Elemental affinities obtained were then evaluated in relation to volatility of these elements during the combustion of these coals in two circulating fluidised-bed power stations. It was found out that higher percentage of the elements bound in silicates brought about lower volatility, while higher elemental proportion with monosulphides association (or bound as exchangeable ion) resulted in higher volatility. The only exception was the behavior of arsenic, whose volatility depended on amount of limestone added during the combustion process (as desulphurisation additive) rather than to its association in coal.
Abstract: Change in impedance of an encircling coil is obtained
in the present paper for the case where the electric conductivity and
magnetic permeability of a metal cylindrical tube depend on the
radial coordinate. The system of equations for the vector potential is
solved by means of the Fourier cosine transform. The solution is
expressed in terms of improper integral containing modified Bessel
functions of complex order.
Abstract: Skip cycle is a working strategy for spark ignition
engines, which allows changing the effective stroke of an engine
through skipping some of the four stroke cycles. This study proposes
a new mechanism to achieve the desired skip-cycle strategy for
internal combustion engines. The air and fuel leakage, which occurs
through the gas exchange, negatively affects the efficiency of the
engine at high speeds and loads. An absolute sealing is assured by
direct use of poppet valves, which are kept in fully closed position
during the skipped mode. All the components of the mechanism were
designed according to the real dimensions of the Anadolu Motor's
gasoline engine and modeled in 3D by means of CAD software. As
the mechanism operates in two modes, two dynamically equivalent
models are established to obtain the force and strength analysis for
critical components.