Abstract: .Hardware realization of a Neural Network (NN), to a large extent depends on the efficient implementation of a single neuron. FPGA-based reconfigurable computing architectures are suitable for hardware implementation of neural networks. FPGA realization of ANNs with a large number of neurons is still a challenging task. This paper discusses the issues involved in implementation of a multi-input neuron with linear/nonlinear excitation functions using FPGA. Implementation method with resource/speed tradeoff is proposed to handle signed decimal numbers. The VHDL coding developed is tested using Xilinx XC V50hq240 Chip. To improve the speed of operation a lookup table method is used. The problems involved in using a lookup table (LUT) for a nonlinear function is discussed. The percentage saving in resource and the improvement in speed with an LUT for a neuron is reported. An attempt is also made to derive a generalized formula for a multi-input neuron that facilitates to estimate approximately the total resource requirement and speed achievable for a given multilayer neural network. This facilitates the designer to choose the FPGA capacity for a given application. Using the proposed method of implementation a neural network based application, namely, a Space vector modulator for a vector-controlled drive is presented
Abstract: Obstructive sleep apnea in patients, between 70 and 80
percent, can be cured with just a posture correcting. The most import
thing to do this is detection of obstructive sleep apnea. Detection of
obstructive sleep apnea can be performed through heart rate variability
analysis using power spectrum density analysis. After HRV analysis
we needed to know the current position information for correcting the
position. The pressure sensors of the array type were used to obtain
position information. These sensors can obtain information from the
experimenter about position. In addition, air cylinder corrected the
position of the experimenter by lifting the bed. The experimenter can
be changed position without breaking during sleep by the system.
Polysomnograph recording were obtained from 10 patients. The
results of HRV analysis were that NLF and LF/HF ratio increased,
while NHF decreased during OSA. Position change had to be done the
periods.
Abstract: This paper reported an experimental research of
steady-state heat transfer behaviour of a gas flowing through a fixed
bed under the different operating conditions. Studies had been carried
out in a fixed-bed packed methanol synthesis catalyst percolated by air
at appropriate flow rate. Both radial and axial direction temperature
distribution had been investigated under the different operating
conditions. The effects of operating conditions including the reactor
inlet air temperature, the heating pipe temperature and the air flow rate
on temperature distribution was investigated and the experimental
results showed that a higher inlet air temperature was conducive to
uniform temperature distribution in the fixed bed. A large temperature
drop existed at the radial direction, and the temperature drop increased
with the heating pipe temperature increasing under the experimental
conditions; the temperature profile of the vicinity of the heating pipe
was strongly affected by the heating pipe temperature. A higher air
flow rate can improve the heat transfer in the fixed bed. Based on the
thermal distribution, heat transfer models of the fixed bed could be
established, and the characteristics of the temperature distribution in
the fixed bed could be finely described, that had an important practical
significance.
Abstract: Wireless mesh networks based on IEEE 802.11
technology are a scalable and efficient solution for next generation
wireless networking to provide wide-area wideband internet access to
a significant number of users. The deployment of these wireless mesh
networks may be within different authorities and without any
planning, they are potentially overlapped partially or completely in
the same service area. The aim of the proposed model is design a new
model to Enhancement Throughput of Unplanned Wireless Mesh
Networks Deployment Using Partitioning Hierarchical Cluster
(PHC), the unplanned deployment of WMNs are determinates there
performance. We use throughput optimization approach to model the
unplanned WMNs deployment problem based on partitioning
hierarchical cluster (PHC) based architecture, in this paper the
researcher used bridge node by allowing interworking traffic between
these WMNs as solution for performance degradation.
Abstract: With the exponential rise in the number of multimedia
applications available, the best-effort service provided by the Internet
today is insufficient. Researchers have been working on new
architectures like the Next Generation Network (NGN) which, by
definition, will ensure Quality of Service (QoS) in an all-IP based
network [1]. For this approach to become a reality, reservation of
bandwidth is required per application per user. WiMAX (Worldwide
Interoperability for Microwave Access) is a wireless communication
technology which has predefined levels of QoS which can be
provided to the user [4]. IPv6 has been created as the successor for
IPv4 and resolves issues like the availability of IP addresses and
QoS. This paper provides a design to use the power of WiMAX as an
NSP (Network Service Provider) for NGN using IPv6. The use of the
Traffic Class (TC) field and the Flow Label (FL) field of IPv6 has
been explained for making QoS requests and grants [6], [7]. Using
these fields, the processing time is reduced and routing is simplified.
Also, we define the functioning of the ASN gateway and the NGN
gateway (NGNG) which are edge node interfaces in the NGNWiMAX
design. These gateways ensure QoS management through
built in functions and by certain physical resources and networking
capabilities.
Abstract: Image compression can improve the performance of
the digital systems by reducing time and cost in image storage
and transmission without significant reduction of the image quality.
Furthermore, the discrete cosine transform has emerged as the new
state-of-the art standard for image compression. In this paper, a
hybrid image compression technique based on reversible blockade
transform coding is proposed. The technique, implemented over
regions of interest (ROIs), is based on selection of the coefficients
that belong to different transforms, depending on the coefficients is
proposed. This method allows: (1) codification of multiple kernals
at various degrees of interest, (2) arbitrary shaped spectrum,and (3)
flexible adjustment of the compression quality of the image and the
background. No standard modification for JPEG2000 decoder was
required. The method was applied over different types of images.
Results show a better performance for the selected regions, when
image coding methods were employed for the whole set of images.
We believe that this method is an excellent tool for future image
compression research, mainly on images where image coding can
be of interest, such as the medical imaging modalities and several
multimedia applications. Finally VLSI implementation of proposed
method is shown. It is also shown that the kernal of Hartley and
Cosine transform gives the better performance than any other model.
Abstract: Worm propagation profiles have significantly changed
since 2003-2004: sudden world outbreaks like Blaster or Slammer
have progressively disappeared and slower but stealthier worms
appeared since, most of them for botnets dissemination. Decreased
worm virulence results in more difficult detection.
In this paper, we describe a stealth worm propagation model
which has been extensively simulated and analysed on a huge virtual
network. The main features of this model is its ability to infect any
Internet-like network in a few seconds, whatever may be its size while
greatly limiting the reinfection attempt overhead of already infected
hosts. The main simulation results shows that the combinatorial
topology of routing may have a huge impact on the worm propagation
and thus some servers play a more essential and significant role than
others. The real-time capability to identify them may be essential to
greatly hinder worm propagation.
Abstract: For a given specific problem an efficient algorithm has been the matter of study. However, an alternative approach orthogonal to this approach comes out, which is called a reduction. In general for a given specific problem this reduction approach studies how to convert an original problem into subproblems. This paper proposes a formal modeling language to support this reduction approach in order to make a solver quickly. We show three examples from the wide area of learning problems. The benefit is a fast prototyping of algorithms for a given new problem. It is noted that our formal modeling language is not intend for providing an efficient notation for data mining application, but for facilitating a designer who develops solvers in machine learning.
Abstract: In this paper, we present a cost-effective wireless
distributed load shedding system for non-emergency scenarios. In
power transformer locations where SCADA system cannot be used,
the proposed solution provides a reasonable alternative that combines
the use of microcontrollers and existing GSM infrastructure to send
early warning SMS messages to users advising them to proactively
reduce their power consumption before system capacity is reached
and systematic power shutdown takes place.
A novel communication protocol and message set have been
devised to handle the messaging between the transformer sites, where
the microcontrollers are located and where the measurements take
place, and the central processing site where the database server is
hosted. Moreover, the system sends warning messages to the endusers
mobile devices that are used as communication terminals. The
system has been implemented and tested via different experimental
results.
Abstract: The Taiwan government has started to promote the “Plain Landscape Afforestation and Greening Program" since 2002. A key task of the program was the payment for environmental services (PES), entitled the “Plain Landscape Afforestation Policy" (PLAP), which was certificated by the Executive Yuan on August 31, 2001 and enacted on January 1, 2002. According to the policy, it is estimated that the total area of afforestation will be 25,100 hectares by December 31, 2007. Until the end of 2007, the policy had been enacted for six years in total and the actual area of afforestation was 8,919.18 hectares. Among them, Taiwan Sugar Corporation (TSC) was accounted for 7,960 hectares (with 2,450.83 hectares as public service area) which occupied 86.22% of the total afforestation area; the private farmland promoted by local governments was accounted for 869.18 hectares which occupied 9.75% of the total afforestation area. Based on the above, we observe that most of the afforestation area in this policy is executed by TSC, and the achievement ratio by TSC is better than by others. It implies that the success of the PLAP is seriously related to the execution of TSC. The objective of this study is to analyze the relevant policy planning of TSC's participation in the PLAP, suggest complementary measures, and draw up effective adjustment mechanisms, so as to improve the effectiveness of executing the policy. Our main conclusions and suggestions are summarized as follows: 1. The main reason for TSC’s participation in the PLAP is based on their passive cooperation with the central government or company policy. Prior to TSC’s participation in the PLAP, their lands were mainly used for growing sugarcane. 2. The main factors of TSC's consideration on the selection of tree species are based on the suitability of land and species. The largest proportion of tree species is allocated to economic forests, and the lack of technical instruction was the main problem during afforestation. Moreover, the method of improving TSC’s future development in leisure agriculture and landscape business becomes a key topic. 3. TSC has developed short and long-term plans on participating in the PLAP for the future. However, there is no great willingness or incentive on budgeting for such detailed planning. 4. Most people from TSC interviewed consider the requirements on PLAP unreasonable. Among them, an unreasonable requirement on the number of trees accounted for the greatest proportion; furthermore, most interviewees suggested that the government should continue to provide incentives even after 20 years. 5. Since the government shares the same goals as TSC, there should be sufficient cooperation and communication that support the technical instruction and reduction of afforestation cost, which will also help to improve effectiveness of the policy.
Abstract: In this study, a fuzzy similarity approach for Arabic
web pages classification is presented. The approach uses a fuzzy
term-category relation by manipulating membership degree for the
training data and the degree value for a test web page. Six measures
are used and compared in this study. These measures include:
Einstein, Algebraic, Hamacher, MinMax, Special case fuzzy and
Bounded Difference approaches. These measures are applied and
compared using 50 different Arabic web pages. Einstein measure was
gave best performance among the other measures. An analysis of
these measures and concluding remarks are drawn in this study.
Abstract: Today-s Information and Knowledge Society has
placed new demands on education and a new paradigm of education
is required. Learning, facilitated by educational systems and the
pedagogic process, is globally undergoing dramatic changes. The aim
of this paper is the development of a simple Instructional Design tool
for E-Learning, named IDEL (Instructional Design for Electronic
Learning), that provides the educators with facilities to create their
own courses with the essential educational material and manage
communication with students. It offers flexibility in the way of
learning and provides ease in employment and reusability of
resources. IDEL is a web-based Instructional System and is designed
to facilitate course design process in accordance with the ADDIE
model and the instructional design principles with emphasis placed
on the use of technology enhanced learning. An example case of
using the ADDIE model to systematically develop a course and its
implementation with the aid of IDEL is given and some results from
student evaluation of the tool and the course are reported.
Abstract: The objective of this research was to investigate biodegradation of water hyacinth (Eichhornia crassipes) to produce bioethanol using dilute-acid pretreatment (1% sulfuric acid) results in high hemicellulose decomposition and using yeast (Pachysolen tannophilus) as bioethanol producing strain. A maximum ethanol yield of 1.14g/L with coefficient, 0.24g g-1; productivity, 0.015g l-1h-1 was comparable to predicted value 32.05g/L obtained by Central Composite Design (CCD). Maximum ethanol yield coefficient was comparable to those obtained through enzymatic saccharification and fermentation of acid hydrolysate using fully equipped fermentor. Although maximum ethanol concentration was low in lab scale, the improvement of lignocellulosic ethanol yield is necessary for large scale production.
Abstract: Flash floods are considered natural disasters that can
cause casualties and demolishing of infra structures. The problem is
that flash floods, particularly in arid and semi arid zones, take place
in very short time. So, it is important to forecast flash floods earlier to
its events with a lead time up to 48 hours to give early warning alert
to avoid or minimize disasters. The flash flood took place over Wadi
Watier - Sinai Peninsula, in October 24th, 2008, has been simulated,
investigated and analyzed using the state of the art regional weather
model. The Weather Research and Forecast (WRF) model, which is a
reliable short term forecasting tool for precipitation events, has been
utilized over the study area. The model results have been calibrated
with the real data, for the same date and time, of the rainfall
measurements recorded at Sorah gauging station. The WRF model
forecasted total rainfall of 11.6 mm while the real measured one was
10.8 mm. The calibration shows significant consistency between
WRF model and real measurements results.
Abstract: This paper addresses the problem of determining the current 3D location of a moving object and robustly tracking it from a sequence of camera images. The approach presented here uses a particle filter and does not perform any explicit triangulation. Only the color of the object to be tracked is required, but not any precisemotion model. The observation model we have developed avoids the color filtering of the entire image. That and the Monte Carlotechniques inside the particle filter provide real time performance.Experiments with two real cameras are presented and lessons learned are commented. The approach scales easily to more than two cameras and new sensor cues.
Abstract: This paper investigates the application of Particle Swarm Optimization (PSO) technique for coordinated design of a Power System Stabilizer (PSS) and a Thyristor Controlled Series Compensator (TCSC)-based controller to enhance the power system stability. The design problem of PSS and TCSC-based controllers is formulated as a time domain based optimization problem. PSO algorithm is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. To compare the capability of PSS and TCSC-based controller, both are designed independently first and then in a coordinated manner for individual and coordinated application. The proposed controllers are tested on a weakly connected power system. The eigenvalue analysis and non-linear simulation results are presented to show the effectiveness of the coordinated design approach over individual design. The simulation results show that the proposed controllers are effective in damping low frequency oscillations resulting from various small disturbances like change in mechanical power input and reference voltage setting.
Abstract: The classical temporal scan statistic is often used to
identify disease clusters. In recent years, this method has become as a
very popular technique and its field of application has been notably
increased. Many bioinformatic problems have been solved with this
technique. In this paper a new scan fuzzy method is proposed. The
behaviors of classic and fuzzy scan techniques are studied with
simulated data. ROC curves are calculated, being demonstrated the
superiority of the fuzzy scan technique.
Abstract: This research is aimed to describe the application of robust regression and its advantages over the least square regression method in analyzing financial data. To do this, relationship between earning per share, book value of equity per share and share price as price model and earning per share, annual change of earning per share and return of stock as return model is discussed using both robust and least square regressions, and finally the outcomes are compared. Comparing the results from the robust regression and the least square regression shows that the former can provide the possibility of a better and more realistic analysis owing to eliminating or reducing the contribution of outliers and influential data. Therefore, robust regression is recommended for getting more precise results in financial data analysis.
Abstract: This essay presents applicative methods to reduce human exposure levels in the area around base transceiver stations in a environment with multiple sources based on ITU-T recommendation K.70. An example is presented to understand the mitigation techniques and their results and also to learn how they can be applied, especially in developing countries where there is not much research on non-ionizing radiations.
Abstract: Classification is an important topic in machine learning
and bioinformatics. Many datasets have been introduced for
classification tasks. A dataset contains multiple features, and the quality of features influences the classification accuracy of the dataset.
The power of classification for each feature differs. In this study, we
suggest the Classification Influence Index (CII) as an indicator of classification power for each feature. CII enables evaluation of the
features in a dataset and improved classification accuracy by transformation of the dataset. By conducting experiments using CII
and the k-nearest neighbor classifier to analyze real datasets, we confirmed that the proposed index provided meaningful improvement
of the classification accuracy.