Abstract: To successfully provide a fast FIR filter with FTT algorithms, overlapped-save algorithms can be used to lower the computational complexity and achieve the desired real-time processing. As the length of the input block increases in order to improve the efficiency, a larger volume of zero padding will greatly increase the computation length of the FFT. In this paper, we use the overlapped block digital filtering to construct a parallel structure. As long as the down-sampling (or up-sampling) factor is an exact multiple lengths of the impulse response of a FIR filter, we can process the input block by using a parallel structure and thus achieve a low-complex fast FIR filter with overlapped-save algorithms. With a long filter length, the performance and the throughput of the digital filtering system will also be greatly enhanced.
Abstract: The Elliptic Curve Digital Signature Algorithm
(ECDSA) is the elliptic curve analogue of DSA, where it is a digital
signature scheme designed to provide a digital signature based on a
secret number known only to the signer and also on the actual
message being signed. These digital signatures are considered the
digital counterparts to handwritten signatures, and are the basis for
validating the authenticity of a connection. The security of these
schemes results from the infeasibility to compute the signature
without the private key. In this paper we introduce a proposed to
development the original ECDSA with more complexity.
Abstract: Sample of CsAg2I3 was prepared by solid state reaction. Then, microstructure parameters of this sample have been determined using wide angle X-ray scattering WAXS method. As well as, Cell parameters of crystal structure have been refined using CHEKCELL program. This analysis states that the lattice intrinsic strainof the sample is so small and the crystal size is on the order of 559Å.
Abstract: Crystallization has been used for the separation of
chloronitrobenzene or CNBs, which are isomeric substances (o-, mand
p-CNB) and important intermediates in chemical productions. Effects of feed composition on the crystallization of m- and p-CNB was first studied. The results conform to the binary phase diagram of
m- and p-CNB. After that, effects of FAU zeolites (NaX, CaX, BaX, NaY and CaY) above the eutectic composition (63.5 and 65.0 wt% m-CNB in the feed) was also investigated. The results showed that
the FAU zeolites significantly affected the precipitates, the
composition of which was shifted from being rich in m-CNB to rich
in p-CNB. Effects of the number of FAU zeolites on the precipitate composition was then studied. The results revealed that the
precipitates from the lower number of the zeolites had higher p-CNB purity than those from the higher number of zeolite.
Abstract: This study considers the problem of determining
operation and maintenance schedules for a containership equipped
with components during its sailing according to a pre-determined
navigation schedule. The operation schedule, which specifies work
time of each component, determines the due-date of each maintenance
activity, and the maintenance schedule specifies the actual start
time of each maintenance activity. The main constraints are component
requirements, workforce availability, working time limitation,
and inter-maintenance time. To represent the problem mathematically,
a mixed integer programming model is developed. Then,
due to the problem complexity, we suggest a heuristic for the objective
of minimizing the sum of earliness and tardiness between the
due-date and the starting time of each maintenance activity. Computational
experiments were done on various test instances and the
results are reported.
Abstract: When the profile information of an existing road is
missing or not up-to-date and the parameters of the vertical
alignment are needed for engineering analysis, the engineer has to recreate
the geometric design features of the road alignment using
collected profile data. The profile data may be collected using
traditional surveying methods, global positioning systems, or digital
imagery. This paper develops a method that estimates the parameters
of the geometric features that best characterize the existing vertical
alignments in terms of tangents and the expressions of the curve, that
may be symmetrical, asymmetrical, reverse, and complex vertical
curves. The method is implemented using an Excel-based
optimization method that minimizes the differences between the
observed profile and the profiles estimated from the equations of the
vertical curve. The method uses a 'wireframe' representation of the
profile that makes the proposed method applicable to all types of
vertical curves. A secondary contribution of this paper is to introduce
the properties of the equal-arc asymmetrical curve that has been
recently developed in the highway geometric design field.
Abstract: In this paper in consideration of each available
techniques deficiencies for speech recognition, an advanced method
is presented that-s able to classify speech signals with the high
accuracy (98%) at the minimum time. In the presented method, first,
the recorded signal is preprocessed that this section includes
denoising with Mels Frequency Cepstral Analysis and feature
extraction using discrete wavelet transform (DWT) coefficients; Then
these features are fed to Multilayer Perceptron (MLP) network for
classification. Finally, after training of neural network effective
features are selected with UTA algorithm.
Abstract: Rockfall is a kind of irregular geological disaster. Its
destruction time, space and movements are highly random. The impact
force is determined by the way and velocity rocks move. The
movement velocity of a rockfall depends on slope gradient of its
moving paths, height, slope surface roughness and rock shapes. For
effectively mitigate and prevent disasters brought by rockfalls, it is
required to precisely calculate the moving paths of a rockfall so as to
provide the best protective design. This paper applies Colorado
Rockfall Simulation Program (CRSP) as our study tool to discuss the
impact of slope shape and surface roughness on the moving paths of a
single rockfall. The analytical results showed that the slope, m=1:1,
acted as the threshold for rockfall bounce height on a monoclinal slight
slope. When JRC ´╝£ 1.2, movement velocity reduced and bounce
height increased as JCR increased. If slope fixed and JRC increased,
the bounce height of rocks increased gradually with reducing
movement velocity. Therefore, the analysis on the moving paths of
rockfalls with CRSP could simulate bouncing of falling rocks. By
analyzing moving paths, velocity, and bounce height of falling rocks,
we could effectively locate impact points of falling rocks on a slope.
Such analysis can be served as a reference for future disaster
prevention and control.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: Recently, a growing interest has emerged on the
development of new and efficient energy sources, due to the inevitable extinction of the nonrenewable energy reserves. One of
these alternative sources which has a great potential and sustainability to meet up the energy demand is biomass energy. This
significant energy source can be utilized with various energy
conversion technologies, one of which is biomass gasification in
supercritical water.
Water, being the most important solvent in nature, has very important characteristics as a reaction solvent under supercritical
circumstances. At temperatures above its critical point (374.8oC and
22.1 MPa), water becomes more acidic and its diffusivity increases.
Working with water at high temperatures increases the thermal
reaction rate, which in consequence leads to a better dissolving of the
organic matters and a fast reaction with oxygen. Hence, supercritical water offers a control mechanism depending on solubility, excellent
transport properties based on its high diffusion ability and new reaction possibilities for hydrolysis or oxidation.
In this study the gasification of a real biomass, namely olive mill
wastewater (OMW), in supercritical water is investigated with the
use of Pt/Al2O3 and Ni/Al2O3 catalysts. OMW is a by-product
obtained during olive oil production, which has a complex nature
characterized by a high content of organic compounds and
polyphenols. These properties impose OMW a significant pollution
potential, but at the same time, the high content of organics makes
OMW a desirable biomass candidate for energy production.
All of the catalytic gasification experiments were made with five
different reaction temperatures (400, 450, 500, 550 and 600°C),
under a constant pressure of 25 MPa. For the experiments conducted
with Ni/Al2O3 catalyst, the effect of five reaction times (30, 60, 90,
120 and 150 s) was investigated. However, procuring that similar
gasification efficiencies could be obtained at shorter times, the experiments were made by using different reaction times (10, 15, 20,
25 and 30 s) for the case of Pt/Al2O3 catalyst. Through these experiments, the effects of temperature, time and catalyst type on the
gasification yields and treatment efficiencies were investigated.
Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: In the real application of active control systems to
mitigate the response of structures subjected to sever external
excitations such as earthquake and wind induced vibrations, since the
capacity of actuators is limited then the actuators saturate. Hence, in
designing controllers for linear and nonlinear structures under sever
earthquakes, the actuator saturation should be considered as a
constraint. In this paper optimal design of active controllers for
nonlinear structures by considering the actuator saturation has been
studied. To this end a method has been proposed based on defining
an optimization problem which considers the minimizing of the
maximum displacement of the structure as objective when a limited
capacity for actuator has been used as a constraint in optimization
problem. To evaluate the effectiveness of the proposed method, a
single degree of freedom (SDF) structure with a bilinear hysteretic
behavior has been simulated under a white noise ground acceleration
of different amplitudes. Active tendon control mechanism, comprised
of pre-stressed tendons and an actuator, and extended nonlinear
Newmark method based instantaneous optimal control algorithm
have been used as active control mechanism and algorithm. To
enhance the efficiency of the controllers, the weights corresponding
to displacement, velocity, acceleration and control force in the
performance index have been found by using the Distributed Genetic
Algorithm (DGA). According to the results it has been concluded
that the proposed method has been effective in considering the
actuator saturation in designing optimal controllers for nonlinear
frames. Also it has been shown that the actuator capacity and the
average value of required control force are two important factors in
designing nonlinear controllers for considering the actuator
saturation.
Abstract: The Linear discriminant analysis (LDA) can be
generalized into a nonlinear form - kernel LDA (KLDA) expediently
by using the kernel functions. But KLDA is often referred to a general
eigenvalue problem in singular case. To avoid this complication, this
paper proposes an iterative algorithm for the two-class KLDA. The
proposed KLDA is used as a nonlinear discriminant classifier, and the
experiments show that it has a comparable performance with SVM.
Abstract: Due to the non- intuitive nature of Quantum
algorithms, it becomes difficult for a classically trained person to
efficiently construct new ones. So rather than designing new
algorithms manually, lately, Genetic algorithms (GA) are being
implemented for this purpose. GA is a technique to automatically
solve a problem using principles of Darwinian evolution. This has
been implemented to explore the possibility of evolving an n-qubit
circuit when the circuit matrix has been provided using a set of
single, two and three qubit gates. Using a variable length population
and universal stochastic selection procedure, a number of possible
solution circuits, with different number of gates can be obtained for
the same input matrix during different runs of GA. The given
algorithm has also been successfully implemented to obtain two and
three qubit Boolean circuits using Quantum gates. The results
demonstrate the effectiveness of the GA procedure even when the
search spaces are large.
Abstract: With the rapid expansion of city scale and the
excessive concentration of population, achieving relative equality of
extracurricular education resources and improving spatial service
performance of relevant facilities become necessary arduous tasks. In
urban space, extracurricular education facilities should offer better
service to its targeted area and promote the equality and efficiency of
education, which is accomplished by the allocation of facilities. Based
on questionnaire and survey for local students in Hangzhou City in
2009, this study classifies extracurricular education facilities in
meg-city and defines the equalization of these facilities. Then it is
suggested to establish extracurricular education facilities system
according to the development level of city and demands of local
students, and to introduce a spatial analysis method into urban
planning through the aspects of spatial distribution, travel cost and
spatial service scope. Finally, the practice of nine sub-districts of
Hangzhou is studied.
Abstract: Lurking behavior is common in information-seeking oriented communities. Transferring users with lurking behavior to be contributors can assist virtual communities to obtain competitive advantages. Based on the ecological cognition framework, this study proposes a model to examine the antecedents of lurking behavior in information-seeking oriented virtual communities. This study argues desire for emotional support, desire for information support, desire for performance-approach, desire for performance -avoidance, desire for mastery-approach, desire for mastery-avoidance, desire for ability trust, desire for benevolence trust, and desire for integrity trust effect on lurking behavior. This study offers an approach to understanding the determinants of lurking behavior in online contexts.
Abstract: In this study, we used a two-stage process and
potassium hydroxide (KOH) to transform waste biomass (rice straw)
into activated carbon and then evaluated the adsorption capacity of the
waste for removing carbofuran from an aqueous solution. Activated
carbon was fast and effective for the removal of carbofuran because of
its high surface area. The native and carbofuran-loaded adsorbents
were characterized by elemental analysis. Different adsorption
parameters, such as the initial carbofuran concentration, contact time,
temperature and pH for carbofuran adsorption, were studied using a
batch system. This study demonstrates that rice straw can be very
effective in the adsorption of carbofuran from bodies of water.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: In this paper, Differential Evolution (DE) algorithm, a new promising evolutionary algorithm, is proposed to train Radial Basis Function (RBF) network related to automatic configuration of network architecture. Classification tasks on data sets: Iris, Wine, New-thyroid, and Glass are conducted to measure the performance of neural networks. Compared with a standard RBF training algorithm in Matlab neural network toolbox, DE achieves more rational architecture for RBF networks. The resulting networks hence obtain strong generalization abilities.