Abstract: During the process of compaction in Hot-Mix Asphalt
(HMA) mixtures, the distance between aggregate particles decreases
as they come together and eliminate air-voids. By measuring the
inter-particle distances in a cut-section of a HMA sample the degree
of compaction can be estimated. For this, a calibration curve is
generated by computer simulation technique when the gradation and
asphalt content of the HMA mixture are known. A two-dimensional
cross section of HMA specimen was simulated using the mixture
design information (gradation, asphalt content and air-void content).
Nearest neighbor distance methods such as Delaunay triangulation
were used to study the changes in inter-particle distance and area
distribution during the process of compaction in HMA. Such
computer simulations would enable making several hundreds of
repetitions in a short period of time without the necessity to compact
and analyze laboratory specimens in order to obtain good statistics on
the parameters defined. The distributions for the statistical
parameters based on computer simulations showed similar trends as
those of laboratory specimens.
Abstract: In this work, a characterization and modeling of
packet loss of a Voice over Internet Protocol (VoIP) communication
is developed. The distributions of the number of consecutive received
and lost packets (namely gap and burst) are modeled from the
transition probabilities of two-state and four-state model.
Measurements show that both models describe adequately the burst
distribution, but the decay of gap distribution for non-homogeneous
losses is better fit by the four-state model. The respective
probabilities of transition between states for each model were
estimated with a proposed algorithm from a set of monitored VoIP
calls in order to obtain representative minimum, maximum and
average values for both models.
Abstract: In the present paper the displacement-based nonconforming quadrilateral affine thin plate bending finite element ARPQ4 is presented, derived directly from non-conforming quadrilateral thin plate bending finite element RPQ4 proposed by Wanji and Cheung [19]. It is found, however, that element RPQ4 is only conditionally unisolvent. The new element is shown to be inherently unisolvent. This convenient property results in the element ARPQ4 being more robust and thus better suited for computations than its predecessor. The convergence is proved and the rate of convergence estimated. The mathematically rigorous proof of convergence presented in the paper is based on Stummel-s generalized patch test and the consideration of the element approximability condition, which are both necessary and sufficient for convergence.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: Virtual touch screen using camera is an ordinary screen which uses a camera to imitate the touch screen by taking a picture of an indicator, e.g., finger, which is laid on the screen, converting the indicator tip position on the picture to the position on the screen, and moving the cursor on the screen to that position. In fact, the indicator is not laid on the screen directly, but it is intervened by the cover at some intervals. In spite of this gap, if the eye-indicator-camera angle is not large, the mapping from the indicator tip positions on the image to the corresponding cursor positions on the screen is not difficult and could be done with a little error. However, the larger the angle is, the bigger the error in the mapping occurs. This paper proposes cursor position estimation model for virtual touch screen using camera which could eliminate this kind of error. The proposed model (i) moves the on-screen pilot cursor to the screen position which locates on the screen at the position just behind the indicator tip when the indicator tip has been looked from the camera position, and then (ii) converts that pilot cursor position to the desirable cursor position (the position on the screen when it has been looked from the user-s eye through the indicator tip) by using the bilinear transformation. Simulation results show the correctness of the estimated cursor position by using the proposed model.
Abstract: In this work we study the effect of several covariates X on a censored response variable T with unknown probability distribution. In this context, most of the studies in the literature can be located in two possible general classes of regression models: models that study the effect the covariates have on the hazard function; and models that study the effect the covariates have on the censored response variable. Proposals in this paper are in the second class of models and, more specifically, on least squares based model approach. Thus, using the bootstrap estimate of the bias, we try to improve the estimation of the regression parameters by reducing their bias, for small sample sizes. Simulation results presented in the paper show that, for reasonable sample sizes and censoring levels, the bias is always smaller for the new proposals.
Abstract: The electrical interaction between two axisymmetric
spheroidal particles in an electrolyte solution is examined numerically.
A Galerkin finite element method combined with a Newton-Raphson
iteration scheme is proposed to evaluate the spatial variation in the
electrical potential, and the result obtained used to estimate the
interaction energy between two particles. We show that if the surface
charge density is fixed, the potential gradient is larger at a point, which
has a larger curvature, and if surface potential is fixed, surface charge
density is proportional to the curvature. Also, if the total interaction
energy against closest surface-to-surface curve exhibits a primary
maximum, the maximum follows the order (oblate-oblate) >
(sphere-sphere)>(oblate-prolate)>(prolate-prolate), and if the curve
has a secondary minimum, the absolute value of the minimum follows
the same order.
Abstract: The main criteria of designing in the most hydraulic
constructions essentially are based on runoff or discharge of water. Two of those important criteria are runoff and return period. Mostly,
these measures are calculated or estimated by stochastic data.
Another feature in hydrological data is their impreciseness.
Therefore, in order to deal with uncertainty and impreciseness, based
on Buckley-s estimation method, a new fuzzy method of evaluating hydrological measures are developed. The method introduces
triangular shape fuzzy numbers for different measures in which both
of the uncertainty and impreciseness concepts are considered. Besides, since another important consideration in most of the
hydrological studies is comparison of a measure during different
months or years, a new fuzzy method which is consistent with special form of proposed fuzzy numbers, is also developed. Finally, to
illustrate the methods more explicitly, the two algorithms are tested on one simple example and a real case study.
Abstract: This study uses simulated meta-analysis to assess the effects of publication bias on meta-analysis estimates and to evaluate the efficacy of the trim and fill method in adjusting for these biases. The estimated effect sizes and the standard error were evaluated in terms of the statistical bias and the coverage probability. The results demonstrate that if publication bias is not adjusted it could lead to up to 40% bias in the treatment effect estimates. Utilization of the trim and fill method could reduce the bias in the overall estimate by more than half. The method is optimum in presence of moderate underlying bias but has minimal effects in presence of low and severe publication bias. Additionally, the trim and fill method improves the coverage probability by more than half when subjected to the same level of publication bias as those of the unadjusted data. The method however tends to produce false positive results and will incorrectly adjust the data for publication bias up to 45 % of the time. Nonetheless, the bias introduced into the estimates due to this adjustment is minimal
Abstract: This paper discusses the implementation of the Kalman
Filter along with the Global Positioning System (GPS) for indoor
robot navigation. Two dimensional coordinates is used for the map
building, and refers to the global coordinate which is attached to the
reference landmark for position and direction information the robot
gets. The Discrete Kalman Filter is used to estimate the robot position,
project the estimated current state ahead in time through time update
and adjust the projected estimated state by an actual measurement at
that time via the measurement update. The navigation test has been
performed and has been found to be robust.
Abstract: Scarcity of resources for biodiversity conservation gives rise to the need of strategic investment with priorities given to the cost of conservation. While the literature provides abundant methodological options for biodiversity conservation; estimating true cost of conservation remains abstract and simplistic, without recognising dynamic nature of the cost. Some recent works demonstrate the prominence of economic theory to inform biodiversity decisions, particularly on the costs and benefits of biodiversity however, the integration of the concept of true cost into biodiversity actions and planning are very slow to come by, and specially on a farm level. Conservation planning studies often use area as a proxy for costs neglecting different land values as well as protected areas. These literature consider only heterogeneous benefits while land costs are considered homogenous. Analysis with the assumption of cost homogeneity results in biased estimation; since not only it doesn’t address the true total cost of biodiversity actions and plans, but also it fails to screen out lands that are more (or less) expensive and/or difficult (or more suitable) for biodiversity conservation purposes, hindering validity and comparability of the results. Economies of scope” is one of the other most neglected aspects in conservation literature. The concept of economies of scope introduces the existence of cost complementarities within a multiple output production system and it suggests a lower cost during the concurrent production of multiple outputs by a given farm. If there are, indeed, economies of scope then simplistic representation of costs will tend to overestimate the true cost of conservation leading to suboptimal outcomes. The aim of this paper, therefore, is to provide first road review of the various theoretical ways in which economies of scope are likely to occur of how they might occur in conservation. Consequently, the paper addresses gaps that have to be filled in future analysis.
Abstract: This paper shows the advantages of the material failure process simulation by improve finite elements with embedded discontinuities, using a new definition of traction vector, dependent on the discontinuity length and the angle. Particularly, two families of this kind of elements are compared: kinematically optimal symmetric and statically and kinematically optimal non-symmetric. The constitutive model to describe the behavior of the material in the symmetric formulation is a traction-displacement jump relationship equipped with softening after reaching the failure surface.
To show the validity of this symmetric formulation, representative numerical examples illustrating the performance of the proposed formulation are presented. It is shown that the non-symmetric family may over or underestimate the energy required to create a discontinuity, as this effect is related with the total length of the discontinuity, fact that is not noticed when the discontinuity path is a straight line.
Abstract: In this paper, we proposed the robust mobile object
detection method for light effect in the night street image block based
updating reference background model using block state analysis.
Experiment image is acquired sequence color video from steady
camera. When suddenly appeared artificial illumination, reference
background model update this information such as street light, sign
light. Generally natural illumination is change by temporal, but
artificial illumination is suddenly appearance. So in this paper for
exactly detect artificial illumination have 2 state process. First process
is compare difference between current image and reference
background by block based, it can know changed blocks. Second
process is difference between current image-s edge map and reference
background image-s edge map, it possible to estimate illumination at
any block. This information is possible to exactly detect object,
artificial illumination and it was generating reference background
more clearly. Block is classified by block-state analysis. Block-state
has a 4 state (i.e. transient, stationary, background, artificial
illumination). Fig. 1 is show characteristic of block-state respectively
[1]. Experimental results show that the presented approach works well
in the presence of illumination variance.
Abstract: The nanotechnology based on epitaxial systems
includes single or arranged misfit dislocations. In general, whatever
is the type of dislocation or the geometry of the array formed by the
dislocations; it is important for experimental studies to know exactly
the stress distribution for which there is no analytical expression [1,
2]. This work, using a numerical analysis, deals with relaxation of
epitaxial layers having at their interface a periodic network of edge
misfit dislocations. The stress distribution is estimated by using
isotropic elasticity. The results show that the thickness of the two
sheets is a crucial parameter in the stress distributions and then in the
profile of the two sheets.
A comparative study between the case of single dislocation and
the case of parallel network shows that the layers relaxed better when
the interface is covered by a parallel arrangement of misfit.
Consequently, a single dislocation at the interface produces an
important stress field which can be reduced by inserting a parallel
network of dislocations with suitable periodicity.
Abstract: In order to consider the effects of the higher modes in
the pushover analysis, during the recent years several multi-modal
pushover procedures have been presented. In these methods the
response of the considered modes are combined by the square-rootof-
sum-of-squares (SRSS) rule while application of the elastic modal
combination rules in the inelastic phases is no longer valid. In this
research the feasibility of defining an efficient alternative
combination method is investigated. Two steel moment-frame
buildings denoted SAC-9 and SAC-20 under ten earthquake records
are considered. The nonlinear responses of the structures are
estimated by the directed algebraic combination of the weighted
responses of the separate modes. The weight of the each mode is
defined so that the resulted response of the combination has a
minimum error to the nonlinear time history analysis. The genetic
algorithm (GA) is used to minimize the error and optimize the weight
factors. The obtained optimal factors for each mode in different cases
are compared together to find unique appropriate weight factors for
each mode in all cases.
Abstract: This paper employs a the variable returns to scale DEA
model to take account of risky assets and estimate the operating
efficiencies for the 21 domestic listed securities firms during the
period 2005-2009. Evidence is found that on average the brokerage
securities firms- operating efficiencies are better than integrated
securities firms. Evidence is also found that the technical inefficiency
from inappropriate management constitutes the main source of the
operating inefficiency for both types of securities firms. Moreover, the
scale economies prevail in brokerage and integrated securities firms,
in other words, which exhibit the characteristic of increasing returns to
scale.
Abstract: The textile industry produces highly coloured
effluents containing polar and non-polar compounds. The textile mill
run by the Assam Polyester Co-operative Society Limited (APOL) is
situated at Rangia, about 55 km from Guwahati (26011' N, 91047' E)
in the northern bank of the river Brahmaputra, Assam (India). This
unit was commissioned in June 1988 and started commercial
production in November 1988. The installed capacity of the weaving
unit was 8000 m/day and that of the processing unit was 20,000
m/day. The mill has its own dyeing unit with a capacity of 1500-2000
kg/day. The western side of the mill consists of vast agricultural land
and the far northern and southern side of the mill has scattered human
population. The eastern side of the mill has a major road for
thoroughfare. The mill releases its effluents into the agricultural land
in the western side of the mill. The present study was undertaken to
assess the impact of the textile mill on surface soil quality in and
around the mill with particular reference to Cr, Mn, Ni and Zn.
Surface soil samples, collected along different directions at 200, 500
and 1000 m were digested and the metals were estimated with
Atomic Absorption Spectrophotometer. The metals were found in the
range of: Cr 50.9 – 105.0 mg kg-1, Mn 19.2- 78.6 mg kg-1, Ni 41.9 –
50.6 mg kg-1 and Zn 187.8 – 1095.8 mg kg-1. The study reveals
enrichment of Cr, Mn, Ni and Zn in the soil near the textile mill.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: Design for cost (DFC) is a method that reduces life
cycle cost (LCC) from the angle of designers. Multiple domain
features mapping (MDFM) methodology was given in DFC. Using
MDFM, we can use design features to estimate the LCC. From the
angle of DFC, the design features of family cars were obtained, such
as all dimensions, engine power and emission volume. At the
conceptual design stage, cars- LCC were estimated using back
propagation (BP) artificial neural networks (ANN) method and
case-based reasoning (CBR). Hamming space was used to measure the
similarity among cases in CBR method. Levenberg-Marquardt (LM)
algorithm and genetic algorithm (GA) were used in ANN. The
differences of LCC estimation model between CBR and artificial
neural networks (ANN) were provided. ANN and CBR separately
each method has its shortcomings. By combining ANN and CBR
improved results accuracy was obtained. Firstly, using ANN selected
some design features that affect LCC. Then using LCC estimation
results of ANN could raise the accuracy of LCC estimation in CBR
method. Thirdly, using ANN estimate LCC errors and correct errors in
CBR-s estimation results if the accuracy is not enough accurate.
Finally, economically family cars and sport utility vehicle (SUV) was
given as LCC estimation cases using this hybrid approach combining
ANN and CBR.
Abstract: In this paper, we propose the low-MAC FEC controller for practical implementation of JPEG2000 image transmission using IEEE 802.15.4. The proposed low-MAC FEC controller has very small HW size and spends little computation to estimate channel state. Because of this advantage, it is acceptable to apply IEEE 802.15.4 which has to operate more than 1 year with battery. For the image transmission, we integrate the low-MAC FEC controller and RCPC coder in sensor node of LR-WPAN. The modified sensor node has increase of 3% hardware size than conventional zigbee sensor node.