Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: In this paper a novel, simple and reliable digital firing
scheme has been implemented for speed control of three-phase
induction motor using ac voltage controller. The system consists of
three-phase supply connected to the three-phase induction motor via
three triacs and its control circuit. The ac voltage controller has three
modes of operation depending on the shape of supply current. The
performance of the induction motor differs in each mode where the
speed is directly proportional with firing angle in two modes and
inversely in the third one. So, the control system has to detect the
current mode of operation to choose the correct firing angle of triacs.
Three sensors are used to feed the line currents to control system to
detect the mode of operation. The control strategy is implemented
using a low cost Xilinx Spartan-3E field programmable gate array
(FPGA) device. Three PI-controllers are designed on FPGA to
control the system in the three-modes. Simulation of the system is
carried out using PSIM computer program. The simulation results
show stable operation for different loading conditions especially in
mode 2/3. The simulation results have been compared with the
experimental results from laboratory prototype.
Abstract: E-Learning systems are used by many learners and
teachers. The developer is developing the e-Learning system. However,
the developer cannot do system construction to satisfy all of
users- demands. We discuss a method of constructing e-Learning
systems where learners and teachers can design, try to use, and share
extending system functions that they want to use; which may be nally
added to the system by system managers.
Abstract: As the mobile Internet has become widespread in
recent years, communication based on mobile networks is increasing.
As a result, security threats have been posed with regard to the
abnormal traffic of mobile networks, but mobile security has been
handled with focus on threats posed by mobile malicious codes, and
researches on security threats to the mobile network itself have not
attracted much attention. In mobile networks, the IP address of the data
packet is a very important factor for billing purposes. If one mobile
terminal use an incorrect IP address that either does not exist or could
be assigned to another mobile terminal, billing policy will cause
problems. We monitor and analyze 3G mobile data networks traffics
for a period of time and finds some abnormal IP packets. In this paper,
we analyze the reason for abnormal IP packets on 3G Mobile Data
Networks. And we also propose an algorithm based on IP address table
that contains addresses currently in use within the mobile data network
to detect abnormal IP packets.
Abstract: Pyritisation halos are identified in weathering crusts and unconsolidated formations at five locations within large fault structure of the Urals’ eastern slope. Electron microscopy reveals the presence of inclusions and growths on pyrite faces – normally on cubic pyrite with striations, or combinations of cubes and other forms. Following neogenesis types are established: native elements and intermetallic compounds (including gold and silver), halogenides, sulphides, sulfosalts, tellurides, sulphotellurides,
selenides, tungstates, sulphates, phosphates, carbon-based substances. Direct relationship is noted between amount and diversity of such mineral phases, and proximity to and scale of ore-grade mineralization. Gold and silver, both in native form and within tellurides, presence of lead (galena, native lead), native tungsten, and, possibly, molybdenite and sulfosalts can indicate gold-bearing formations. First find of native tungsten in the Urals is for the first time – in crystallised and druse-like form. Link is suggested between unusual mineralization and “reducing” hydrothermal fluids from deep-seated faults at later stages of Urals’ reactivation.
Abstract: Coal tar is a liquid by-product of the process of coal
gasification and carbonation. This liquid oil mixture contains various
kinds of useful compounds such as phenol, o-cresol, and p-cresol.
These compounds are widely used as raw material for insecticides,
dyes, medicines, perfumes, coloring matters, and many others.
This research needed to be done that given the optimum conditions
for the separation of phenol, o-cresol, and p-cresol from the coal tar
by solvent extraction process. The aim of the present work was to
study the effect of two kinds of aqueous were used as solvents:
methanol and acetone solutions, the effect of temperature (298, 306,
and 313K) and mixing (30, 35, and 40rpm) for the separation of
phenol, o-cresol, and p-cresol from coal tar by solvent extraction.
Results indicated that phenol, o-cresol, and p-cresol in coal tar
were selectivity extracted into the solvent phase and these
components could be separated by solvent extraction. The aqueous
solution of methanol, mass ratio of solvent to feed, Eo/Ro=1,
extraction temperature 306K and mixing 35 rpm were the most
efficient for extraction of phenol, o-cresol, and p-cresol from coal tar.
Abstract: Natural gas usually includes H2S component which is
very toxic, hazardous and corrosive to environment, human being and
process equipments, respectively. Therefore, sweetening of the gas
(separation of H2S) is inevitable. To achieve this purpose, using
packed-bed columns with liquid absorbents such as MEA or DEA is
very common. Due to some problems of usual packed columns
especially high pressure drop of gas phase, a novel kind of them
called wetted-wire column (WWC) has been invented. The column
decreases the pressure drop significantly and improves the absorption
efficiency. The packings are very thin rods (like wire) and as long as
column. The column has 100 wires with a triangular arrangement and
counter current flows of gas and liquid phases. The observation
showed that at the same conditions, the absorption performance was
quite comparable to conventional packed-bed towers and a very low
pressure drop.
Abstract: Designing and implementing intelligent systems has become a crucial factor for the innovation and development of better products of space technologies. A neural network is a parallel system, capable of resolving paradigms that linear computing cannot. Field programmable gate array (FPGA) is a digital device that owns reprogrammable properties and robust flexibility. For the neural network based instrument prototype in real time application, conventional specific VLSI neural chip design suffers the limitation in time and cost. With low precision artificial neural network design, FPGAs have higher speed and smaller size for real time application than the VLSI and DSP chips. So, many researchers have made great efforts on the realization of neural network (NN) using FPGA technique. In this paper, an introduction of ANN and FPGA technique are briefly shown. Also, Hardware Description Language (VHDL) code has been proposed to implement ANNs as well as to present simulation results with floating point arithmetic. Synthesis results for ANN controller are developed using Precision RTL. Proposed VHDL implementation creates a flexible, fast method and high degree of parallelism for implementing ANN. The implementation of multi-layer NN using lookup table LUT reduces the resource utilization for implementation and time for execution.
Abstract: This study investigated the relationship between urban
and rural ozone concentrations and quantified the extent to which
ambient rural conditions and the concentrations of other pollutants
can be used to predict urban ozone concentrations. The study
describes the variations of ozone in weekday and weekends as well as
the daily maximum recorded at selected monitoring stations. The
results showed that Putrajaya station had the highest concentrations
of O3 on weekend due the titration of NO during the weekday.
Additionally, Jerantut had the lowest average concentration with a
reading value high on Wednesdays. The comparisons of average and
maximum concentrations of ozone for the three stations showed that
the strongest significant correlation is recorded in Jerantut station
with the value R2= 0.769. Ozone concentrations originating from a
neighbouring urban site form a better predictor to the urban ozone
concentrations than widespread rural ozone at some levels of
temporal averaging. It is found that in urban and rural of Malaysian
peninsular, the concentration of ozone depends on the concentration
of NOx and seasonal meteorological factors. The HYSPLIT Model
(the northeast monsoon) showed that the wind direction can also
influence the concentration of ozone in the atmosphere in the studied
areas.
Abstract: Social Business Process Management (SBPM)
promises to overcome limitations of traditional BPM by allowing
flexible process design and enactment through the involvement of
users from a social community. This paper proposes a meta-model
and architecture for socially driven business process management
systems. It discusses the main facets of the architecture such as goalbased
role assignment that combines social recommendations with
user profile, and process recommendation, through a real example of
a charity organization.
Abstract: This paper proposes a method which reduces power consumption in single-error correcting, double error-detecting checker circuits that perform memory error correction code. Power is minimized with little or no impact on area and delay, using the degrees of freedom in selecting the parity check matrix of the error correcting codes. The genetic algorithm is employed to solve the non linear power optimization problem. The method is applied to two commonly used SEC-DED codes: standard Hamming and odd column weight Hsiao codes. Experiments were performed to show the performance of the proposed method.
Abstract: The main aim of this paper was to investigate the
existing architecture in Cyprus, and thus identify and describe the
overall architectural rationale of the built environment. In Cyprus,
where individuals live in a society that reflects postmodern
paradigms rather than modern ones, the existing built environment
has many different reflections of the structure of its society.
Abstract: The main criteria of designing in the most hydraulic
constructions essentially are based on runoff or discharge of water. Two of those important criteria are runoff and return period. Mostly,
these measures are calculated or estimated by stochastic data.
Another feature in hydrological data is their impreciseness.
Therefore, in order to deal with uncertainty and impreciseness, based
on Buckley-s estimation method, a new fuzzy method of evaluating hydrological measures are developed. The method introduces
triangular shape fuzzy numbers for different measures in which both
of the uncertainty and impreciseness concepts are considered. Besides, since another important consideration in most of the
hydrological studies is comparison of a measure during different
months or years, a new fuzzy method which is consistent with special form of proposed fuzzy numbers, is also developed. Finally, to
illustrate the methods more explicitly, the two algorithms are tested on one simple example and a real case study.
Abstract: Functional gastrointestinal disorders affect millions of people spread all age regardless of race and sex. There are, however, rare diagnostic methods for the functional gastrointestinal disorders because functional disorders show no evidence of organic and physical causes. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Aim of this study is, therefore, to develop a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristic above related to the rigidity of the gastrointestinal tract well. Ultrasound system was designed. The system consisted of transmitter, ultrasonic transducer, receiver, TGC, and CPLD, and verified via a phantom test. For the phantom test, ten soft-tissue specimens were harvested from porcine. Five of them were then treated chemically to mimic a rigid condition of gastrointestinal tract well, which was induced by functional gastrointestinal disorders. Additionally, the specimens were tested mechanically to identify if the mimic was reasonable. The customized ultrasound system was finally verified through application to human subjects with/without functional gastrointestinal disorders (Normal and Patient Groups). It was identified from the mechanical test that the chemically treated specimens were more rigid than normal specimen. This finding was favorably compared with the result obtained from the phantom test. The phantom test also showed that ultrasound system well described the specimen geometric characteristics and detected an alteration in the specimens. The maximum amplitude of the ultrasonic reflective signal in the rigid specimens (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal specimens (0.1±0.0Vp-p). Clinical tests using our customized ultrasound system for human subject showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3Vp-p) were generally higher than those in normal group (0.1±0.2Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These results suggest that newly designed diagnostic system based on ultrasound technique may diagnose enough the functional gastrointestinal disorders.
Abstract: The design of chaos-based secure communication
via synchronized modified Chua-s systems is investigated in
this paper. A continuous control law is proposed to ensure
synchronization of the master and slave modified Chua-s
systems by using the variable structure control technique.
Particularly, the concept of extended systems is introduced
such that a continuous control input is obtained to avoid
chattering phenomenon. Then, it becomes possible to ensure
that the message signal embedded in the transmitter can be
recovered in the receiver.
Abstract: In the self-stabilizing algorithmic paradigm, each node has a local view of the system, in a finite amount of time the system converges to a global state with desired property. In a graph G =
(V, E), a subset S C V is a 2-packing if Vi c V: IN[i] n SI
Abstract: Since its independence in 1962, Algeria has struggled
to establish an educational system tailored to the needs of the
population it may address. Considering the historical connection with
France, Algeria has always looked at the French language as a
cultural imperative until late in the seventies. After the Arabization
policy of 1971 and the socioeconomic changes taking place
worldwide, the use of English as a communicating vehicle started to
gain more space within globalized Algeria. Consequently, disparities
in the use of French started to fade away at the cross-roads leaving
more space to the teaching of English as a second foreign language.
Moreover, the introduction of the Bologna Process and the
European Credit Transfer System in Higher Education has
necessitated some innovations in the design and development of new
curricula adapted to the socioeconomic market. In this paper, I will
try to highlight the important historical dimensions Algeria has taken
towards the implementation of an English language methodology and
to the status it acquired from second foreign language, to first foreign
language to “the language of knowledge and sciences". I will also
propose new pedagogical perspectives for a better treatment of the
English language in order to encourage independent and autonomous
learning.
Abstract: The Kansei engineering is a technology which
converts human feelings into quantitative terms and helps designers
develop new products that meet customers- expectation. Standard
Kansei engineering procedure involves finding relationships between
human feelings and design elements of which many researchers have
found forward and backward relationship through various soft
computing techniques. In this paper, we proposed the framework of
Kansei engineering linking relationship not only between human
feelings and design elements, but also the whole part of product, by
constructing association rules. In this experiment, we obtain input
from emotion score that subjects rate when they see the whole part of
the product by applying semantic differentials. Then, association
rules are constructed to discover the combination of design element
which affects the human feeling. The results of our experiment
suggest the pattern of relationship of design elements according to
human feelings which can be derived from the whole part of product.
Abstract: Iodine radionuclides in accident releases under severe
accident conditions at NPP with VVER are the most radiationimportant
with a view to population dose generation at the beginning
of the accident. To decrease radiation consequences of severe
accidents the technical solutions for severe accidents management
have been proposed in MIR.1200 project, with consideration of the
measures for suppression of volatile iodine forms generation in the
containment. Behavior dynamics of different iodine forms in the
containment under severe accident conditions has been analyzed for
the purpose of these technical solutions justification.
Abstract: Carbon fibers have specific characteristics in
comparison with industrial and structural materials used in different
applications. Special properties of carbon fibers make them attractive
for reinforcing and fabrication of composites. These fibers have been
utilized for composites of metals, ceramics and plastics. However,
it-s mainly used in different forms to reinforce lightweight polymer
materials such as epoxy resin, polyesters or polyamides. The
composites of carbon fiber are stronger than steel, stiffer than
titanium, and lighter than aluminum and nowadays they are used in a
variety of applications. This study explains applications of carbon
fibers in different fields such as space, aviation, transportation,
medical, construction, energy, sporting goods, electronics, and the
other commercial/industrial applications. The last findings of
composites with polymer, metal and ceramic matrices containing
carbon fibers and their applications in the world investigated.
Researches show that carbon fibers-reinforced composites due to
unique properties (including high specific strength and specific
modulus, low thermal expansion coefficient, high fatigue strength,
and high thermal stability) can be replaced with common industrial
and structural materials.