Abstract: In this paper, a novel Linear Feedback Shift Register
(LFSR) with Look Ahead Clock Gating (LACG) technique is
presented to reduce the power consumption in modern processors
and System-on-Chip. Clock gating is a predominant technique used
to reduce unwanted switching of clock signals. Several clock gating
techniques to reduce the dynamic power have been developed, of
which LACG is predominant. LACG computes the clock enabling
signals of each flip-flop (FF) one cycle ahead of time, based on the
present cycle data of the flip-flops on which it depends. It overcomes
the timing problems in the existing clock gating methods like datadriven
clock gating and Auto-Gated flip-flops (AGFF) by allotting a
full clock cycle for the determination of the clock enabling signals.
Further to reduce the power consumption in LACG technique, FFs
can be grouped so that they share a common clock enabling signal.
Simulation results show that the novel grouped LFSR with LACG
achieves 15.03% power savings than conventional LFSR with LACG
and 44.87% than data-driven clock gating.
Abstract: The objective of this study was to synthesize and
characterize the poly(alkenoic acid)s with different molecular
structures, use these polymers to formulate a dental cement
restorative, and study the effect of molecular structures on reaction
kinetics, viscosity, and mechanical strengths of the formed polymers
and cement restoratives. In this study, poly(alkenoic acid)s with
different molecular structures were synthesized. The purified
polymers were formulated with commercial Fuji II LC glass fillers to
form the experimental cement restoratives. The reaction kinetics was
studied via 1HNMR spectroscopy. The formed restoratives were
evaluated using compressive strength, diametral tensile strength,
flexural strength, hardness and wear-resistance tests. Specimens were
conditioned in distilled water at 37oC for 24 h prior to testing. Fuji II
LC restorative was used as control. The results show that the higher
the arm number and initiator concentration, the faster the reaction
was. It was also found that the higher the arm number and branching
that the polymer had, the lower the viscosity of the polymer in water
and the lower the mechanical strengths of the formed restorative. The
experimental restoratives were 31-53% in compressive strength, 37-
55% in compressive modulus, 80-126% in diametral tensile strength,
76-94% in flexural strength, 4-21% in fracture toughness and 53-96%
in hardness higher than Fuji II LC. For wear test, the experimental
restoratives were only 5.4-13% of abrasive and 6.4-12% of attritional
wear depths of Fuji II LC in each wear cycle. The aging study also
showed that all the experimental restoratives increased their strength
continuously during 30 days, unlike Fuji II LC. It is concluded that
polymer molecular structures have significant and positive impact on
mechanical properties of dental cement restoratives.
Abstract: Increasingly complex modern power systems require
stability, especially for transient and small disturbances. Transient
stability plays a major role in stability during fault and large
disturbance. This paper compares a power system stabilizer (PSS)
and static Var compensator (SVC) to improve damping oscillation
and enhance transient stability. The effectiveness of a PSS connected
to the exciter and/or governor in damping electromechanical
oscillations of isolated synchronous generator was tested. The SVC
device is a member of the shunt FACTS (flexible alternating current
transmission system) family, utilized in power transmission systems.
The designed model was tested with a multi-machine system
consisting of four machines six bus, using MATLAB/SIMULINK
software. The results obtained indicate that SVC solutions are better
than PSS.
Abstract: In this paper, a novel fuzzy approach is developed
while solving the Dynamic Routing and Wavelength Assignment
(DRWA) problem in optical networks with Wavelength Division
Multiplexing (WDM). In this work, the effect of nonlinear and linear
impairments such as Four Wave Mixing (FWM) and amplifier
spontaneous emission (ASE) noise are incorporated respectively. The
novel algorithm incorporates fuzzy logic controller (FLC) to reduce
the effect of FWM noise and ASE noise on a requested lightpath
referred in this work as FWM aware fuzzy dynamic routing and
wavelength assignment algorithm. The FWM crosstalk products and
the static FWM noise power per link are pre computed in order to
reduce the set up time of a requested lightpath, and stored in an
offline database. These are retrieved during the setting up of a
lightpath and evaluated online taking the dynamic parameters like
cost of the links into consideration.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Background: To improve the delivery of paediatric
healthcare in low resource settings, Community Health Workers
(CHW) have been provided with a paper-based set of protocols
known as Community Case Management (CCM). Yet research has
shown that CHW adherence to CCM guidelines is poor, ultimately
impacting health service delivery. Digitising the CCM guidelines via
mobile technology is argued in extant literature to improve CHW
adherence. However, little research exist which outlines how (a) this
process can be digitised and (b) adherence could be improved as a
result. Aim: To explore how an electronic mobile version of CCM
(eCCM) can overcome issues associated with the paper-based CCM
protocol (inadequate adherence to guidelines) vis-à-vis service
blueprinting. This service blueprint will outline how (a) the CCM
process can be digitised using mobile Clinical Decision Support
Systems software to support clinical decision-making and (b)
adherence can be improved as a result. Method: Development of a
single service blueprint for a standalone application which visually
depicts the service processes (eCCM) when supporting the CHWs,
using an application known as Supporting LIFE (SL eCCM app) as
an exemplar. Results: A service blueprint is developed which
illustrates how the SL eCCM app can be utilised by CHWs to assist
with the delivery of healthcare services to children. Leveraging
smartphone technologies can (a) provide CHWs with just-in-time
data to assist with their decision making at the point-of-care and (b)
improve CHW adherence to CCM guidelines. Conclusions: The
development of the eCCM opens up opportunities for the CHWs to
leverage the inherent benefit of mobile devices to assist them with
health service delivery in rural settings. To ensure that benefits are
achieved, it is imperative to comprehend the functionality and form
of the eCCM service process. By creating such a service blueprint for
an eCCM approach, CHWs are provided with a clear picture
regarding the role of the eCCM solution, often resulting in buy-in
from the end-users.
Abstract: Lateral torsional buckling is a global buckling mode
which should be considered in design of slender structural members
under flexure about their strong axis. It is possible to compute the
load which causes lateral torsional buckling of a beam by finite
element analysis, however, closed form equations are needed in
engineering practice for calculation ease which can be obtained by
using energy method. In lateral torsional buckling applications of
energy method, a proper function for the critical lateral torsional
buckling mode should be chosen which can be thought as the
variation of twisting angle along the buckled beam. Accuracy of the
results depends on how close is the chosen function to the exact
mode. Since critical lateral torsional buckling mode of the cantilever
I-beams varies due to material properties, section properties and
loading case, the hardest step is to determine a proper mode function
in application of energy method. This paper presents an approximate function for critical lateral
torsional buckling mode of doubly symmetric cantilever I-beams.
Coefficient matrices are calculated for concentrated load at free end,
uniformly distributed load and constant moment along the beam
cases. Critical lateral torsional buckling modes obtained by presented
function and exact solutions are compared. It is found that the modes
obtained by presented function coincide with differential equation
solutions for considered loading cases.
Abstract: In this study, a general approach to the reliability
based limit analysis of laterally loaded piles is presented. In
engineering practice the uncertainties play a very important role. The
aim of this study is to evaluate the lateral load capacity of free-head
and fixed-head long pile when plastic limit analysis is considered. In
addition to the plastic limit analysis to control the plastic behaviour
of the structure, uncertain bound on the complementary strain energy
of the residual forces is also applied. This bound has significant effect
for the load parameter. The solution to reliability-based problems is
obtained by a computer program which is governed by the reliability
index calculation.
Abstract: Temperature regulating system by gaseous nitrogen is
of importance to the space environment simulator, which keeps the
shrouds in the temperature range from -150°C to +150°C. Liquid
nitrogen spray equipment is one of the most critical parts in the
temperature regulating system by gaseous nitrogen. Y type jet
atomizer and internal mixing atomizer of the liquid nitrogen spray
equipment are studied in this paper, 2D/3D atomizer model was
established and grid division was conducted respectively by the
software of Catia and ICEM. Based on the above preparation,
numerical simulation on the spraying process of the atomizer by
FLUENT is performed. Using air and water as the medium,
comparison between the tests and numerical simulation was conducted
and the results of two ways match well. Hence, it can be conclude that
this atomizer model can be applied in the numerical simulation of
liquid nitrogen spray equipment.
Abstract: Cancer is still one of the serious diseases threatening
the lives of human beings. How to have an early diagnosis and
effective treatment for tumors is a very important issue. The animal
carcinoma model can provide a simulation tool for the studies of
pathogenesis, biological characteristics, and therapeutic effects.
Recently, drug delivery systems have been rapidly developed to
effectively improve the therapeutic effects. Liposome plays an
increasingly important role in clinical diagnosis and therapy for
delivering a pharmaceutic or contrast agent to the targeted sites.
Liposome can be absorbed and excreted by the human body, and is
well known that no harm to the human body. This study aimed to
compare the therapeutic effects between encapsulated (doxorubicin
liposomal, Lipodox) and un-encapsulated (doxorubicin, Dox)
anti-tumor drugs using magnetic resonance imaging (MRI).
Twenty-four New Zealand rabbits implanted with VX2 carcinoma at
left thighs were classified into three groups: control group (untreated),
Dox-treated group, and LipoDox-treated group, 8 rabbits for each
group. MRI scans were performed three days after tumor implantation.
A 1.5T GE Signa HDxt whole body MRI scanner with a high
resolution knee coil was used in this study. After a 3-plane localizer
scan was performed, three-dimensional (3D) fast spin echo (FSE)
T2-weighted Images (T2WI) was used for tumor volumetric
quantification. Afterwards, two-dimensional (2D) spoiled gradient
recalled echo (SPGR) dynamic contrast-enhanced (DCE) MRI was
used for tumor perfusion evaluation. DCE-MRI was designed to
acquire four baseline images, followed by contrast agent Gd-DOTA
injection through the ear vein of rabbit. A series of 32 images were
acquired to observe the signals change over time in the tumor and
muscle. The MRI scanning was scheduled on a weekly basis for a
period of four weeks to observe the tumor progression longitudinally.
The Dox and LipoDox treatments were prescribed 3 times in the first
week immediately after the first MRI scan; i.e. 3 days after VX2 tumor
implantation. ImageJ was used to quantitate tumor volume and time
course signal enhancement on DCE images. The changes of tumor size
showed that the growth of VX2 tumors was effectively inhibited for
both LipoDox-treated and Dox-treated groups. Furthermore, the tumor
volume of LipoDox-treated group was significantly lower than that of
Dox-treated group, which implies that LipoDox has better therapeutic effect than Dox. The signal intensity of LipoDox-treated group is
significantly lower than that of the other two groups, which implies
that targeted therapeutic drug remained in the tumor tissue. This study
provides a radiation-free and non-invasive MRI method for
therapeutic monitoring of targeted liposome on an animal tumor
model.
Abstract: A growing demand is felt today for realistic 3D
models enabling the cognition and popularization of historical-artistic
heritage. Evaluation and preservation of Cultural Heritage is
inextricably connected with the innovative processes of gaining,
managing, and using knowledge. The development and perfecting of
techniques for acquiring and elaborating photorealistic 3D models,
made them pivotal elements for popularizing information of objects
on the scale of architectonic structures.
Abstract: Underwater acoustic networks have attracted great
attention in the last few years because of its numerous applications.
High data rate can be achieved by efficiently modeling the physical
layer in the network protocol stack. In Acoustic medium,
propagation speed of the acoustic waves is dependent on many
parameters such as temperature, salinity, density, and depth.
Acoustic propagation speed cannot be modeled using standard
empirical formulas such as Urick and Thorp descriptions. In this
paper, we have modeled the acoustic channel using real time data of
temperature, salinity, and speed of Bay of Bengal (Indian Coastal
Region). We have modeled the acoustic channel by using Mackenzie
speed equation and real time data obtained from National Institute of
Oceanography and Technology. It is found that acoustic propagation
speed varies between 1503 m/s to 1544 m/s as temperature and
depth differs. The simulation results show that temperature, salinity,
depth plays major role in acoustic propagation and data rate
increases with appropriate data sets substituted in the simulated
model.
Abstract: This paper presents the design and implementation
details of a complete unmanned aerial system (UAS) based
on commercial-off-the-shelf (COTS) components, focusing on
safety, security, search and rescue scenarios in GPS-denied
environments. In particular, The aerial platform is capable
of semi-autonomously navigating through extremely low-light,
GPS-denied indoor environments based on onboard sensors only,
including a downward-facing optical flow camera. Besides, an
additional low-cost payload camera system is developed to stream
both infra-red video and visible light video to a ground station in
real-time, for the purpose of detecting sign of life and hidden humans.
The total cost of the complete system is estimated to be $1150,
and the effectiveness of the system has been tested and validated
in practical scenarios.
Abstract: In this paper a very simple and effective user
administration view of computing clusters systems is implemented in
order of friendly provide the configuration and monitoring of
distributed application executions. The user view, the administrator
view, and an internal control module create an illusionary
management environment for better system usability. The
architecture, properties, performance, and the comparison with others
software for cluster management are briefly commented.
Abstract: The garment manufacturing industry involves
sequential processes that are subjected to uncontrollable variations.
The industry depends on the skill of labour in handling the varieties
of fabrics and accessories, machines, as well as complicated sewing
operation. Due to these reasons, garment manufacturers have created
systems to monitor and to control the quality of the products on a
regular basis by conducting quality approaches to minimize variation.
With that, the aim of this research has been to ascertain the quality
approaches deployed by Malaysian garment manufacturers in three
key areas - quality systems and tools; quality control and types of
inspection; as well as sampling procedures chosen for garment
inspection. Besides, the focus of this research was to distinguish the
quality approaches adopted by companies that supplied finished
garments to both domestic and international markets. Feedback from
each company representative has been obtained via online survey,
which comprised of five sections and 44 questions on the
organizational profile and the quality approaches employed in the
garment industry. As a result, the response rate was 31%. The results
revealed that almost all companies have established their own
mechanism of process control by conducting a series of quality
inspections for daily production, either it was formally set up or
otherwise. In addition, quality inspection has been the predominant
quality control activity in the garment manufacturing, while the level
of complexity of these activities was substantially dictated by the
customers. Moreover, AQL-based sampling was utilized by
companies dealing with exports, whilst almost all the companies that
only concentrated on the domestic market were comfortable using
their own sampling procedures for garment inspection. Hence, this
research has provided insights into the implementation of a number
of quality approaches that were perceived as important and useful in
the garment manufacturing sector, which is truly labour-intensive.
Abstract: South Africa is in its post-industrial era moving from
the primary and secondary sector to the tertiary sector. The study
investigated the impact of the disaggregated energy consumption
(coal, oil, and electricity) on the primary, secondary and tertiary
sectors of the economy between 1980 and 2012 in South Africa.
Using vector error correction model, it was established that South
Africa is an energy dependent economy, and that energy (especially
electricity and oil) is a limiting factor of growth. This implies that
implementation of energy conservation policies may hamper
economic growth. Output growth is significantly outpacing energy
supply, which has necessitated load shedding. To meet up the excess
energy demand, there is a need to increase the generating capacity
which will necessitate increased investment in the electricity sector as
well as strategic steps to increase oil production. There is also need to
explore more renewable energy sources, in order to meet the growing
energy demand without compromising growth and environmental
sustainability. Policy makers should also pursue energy efficiency
policies especially at sectoral level of the economy.
Abstract: Hypertension is a common condition causing cardio
and cerebrovascular complications. Portugal has one of the highest
mortality rates from stroke and a high prevalence of hypertension.
Systolic Blood Pressure (SBP) is an important risk factor for
cardiovascular events (myocardial infarction and stroke) and
premature mortality, particularly in the elderly population. The
present study aims to estimate the prevalence of hypertension in a
Portuguese population living in a coastal city and to identify some of
its determinants (namely gender, age, the body mass index and
physical activity frequency). A total of 91 adults who attended three pharmacies of a coastal
city in the center of Portugal, between May and August of 2013 were
evaluated. Attendants who reported to have diabetes or taking
antihypertensive drugs in the 2 previous weeks were excluded from
the study. Sociodemographic factors, BMI, habits of exercise and BP
were assessed. Hypertension was defined as blood pressure ≥140/90
mmHg. The majority of the studied population was constituted by women
(75.8%), with a mean age of 54.2±1.6 years old, married or living in
civil union and that had completed secondary school or had higher
education (40%). They presented a mean BMI of 26.2±4.76 Kg/m2.,
and were sedentary. The mean BP was 127.0±17.77mmHg- 74.69 ±
9.53. In this population we found 4.3% of people with hypertension
and 16.1% with normal high blood pressure. Men exhibit a tendency to present higher systolic blood pressure
values than women. Of all the factors considered, SBP values also
tended to be higher with age and higher BMI values.
Despite the fact that the mean values of SBP did not present values
higher than 140 mmHg we must be concerned because the studied
population is undiagnosed for hypertension. Although this is a preliminary study, it might be a prelude to the
upcoming research about the underlying factors responsible for the
occurrence of SBP.
Abstract: The aim of this study is to empirically investigate the
mediating impact of export performance (EP) between technological
advancement capabilities and business performance (BP) of
Malaysian manufacturing micro, small and medium sized enterprises
(MSME’s). Firm’s technological advancement resources are
hypothesized as a platform to enhance both exports and BP of
manufacturing MSMEs in Malaysia. This study is twofold, primary it
has investigated that technological advancement capabilities helps to
appreciates main performance measures noted in terms of EP and
Secondly, it investigates that how efficiently and effectively
technological advancement capabilities can contribute in overall
Malaysian MSME’s BP. Smart PLS-3 statistical software is used to
know the association between technological advancement
capabilities, MSME’s EP and BP. In this study, the data was
composed from Malaysian manufacturing MSME’s in east coast
industrial zones known as the manufacturing hub of MSMEs. Seven
hundred and fifty (750) questionnaires were distributed, but only 148
usable questionnaires are returned. The finding of this study indicated
that technological advancement capabilities helps to strengthen the
export in term of time and cost efficient and it plays a significant role
in appreciating their BP. This study is helpful for small and medium
enterprise owners who intend to expand their business overseas and
though smart technological advancement resources they can achieve
their business competitiveness and excellence both at local and
international markets.
Abstract: Hydraulic fracturing is one of the most important
stimulation techniques available to the petroleum engineer to extract
hydrocarbons in tight gas sandstones. It allows more oil and gas
production in tight reservoirs as compared to conventional means.
The main aim of the study is to optimize the hydraulic fracturing as
technique and for this purpose three multi-zones layer formation is
considered and fractured contemporaneously. The three zones are
named as Zone1 (upper zone), Zone2 (middle zone) and Zone3
(lower zone) respectively and they all occur in shale rock. Simulation was performed with Mfrac integrated software which
gives a variety of 3D fracture options. This simulation process
yielded an average fracture efficiency of 93.8%for the three
respective zones and an increase of the average permeability of the
rock system. An average fracture length of 909 ft with net height
(propped height) of 210 ft (average) was achieved. Optimum
fracturing results was also achieved with maximum fracture width of
0.379 inches at an injection rate of 13.01 bpm with 17995 Mscf of
gas production.
Abstract: In this work, repaired crack in 6061- T6 aluminum
plate with composite patches presented, firstly we determine the
displacement, strain and stress, also the first six mode shape of the
plate, secondly we took the same model adding central crack
initiation, which is located in the center of the plate, its seize vary
from 20 mm to 60 mm and we compare the first results with second.
Thirdly we repair various cracks with composite patch (carbon/
epoxy) and for (2 layers, 4 layers). Finally the comparison of stress,
strain, displacement and six first natural frequencies between un-cracked
specimen, crack propagation and composite patch repair.