Abstract: The porous silicon (PS), formed from the anodization
of a p+ type substrate silicon, consists of a network organized in a
pseudo-column as structure of multiple side ramifications. Structural
micro-topology can be interpreted as the fraction of the interconnected
solid phase contributing to thermal transport. The
reduction of dimensions of silicon of each nanocristallite during the
oxidation induced a reduction in thermal conductivity. Integration of
thermal sensors in the Microsystems silicon requires an effective
insulation of the sensor element. Indeed, the low thermal conductivity
of PS consists in a very promising way in the fabrication of integrated
thermal Microsystems.In this work we are interesting in the
measurements of thermal conductivity (on the surface and in depth)
of PS by the micro-Raman spectroscopy. The thermal conductivity is
studied according to the parameters of anodization (initial doping and
current density. We also, determine porosity of samples by
spectroellipsometry.
Abstract: In the present study the efficiency of Big Bang-Big
Crunch (BB-BC) algorithm is investigated in discrete structural
design optimization. It is shown that a standard version of the BB-BC
algorithm is sometimes unable to produce reasonable solutions to
problems from discrete structural design optimization. Two
reformulations of the algorithm, which are referred to as modified
BB-BC (MBB-BC) and exponential BB-BC (EBB-BC), are
introduced to enhance the capability of the standard algorithm in
locating good solutions for steel truss and frame type structures,
respectively. The performances of the proposed algorithms are
experimented and compared to its standard version as well as some
other algorithms over several practical design examples. In these
examples, steel structures are sized for minimum weight subject to
stress, stability and displacement limitations according to the
provisions of AISC-ASD.
Abstract: Particle damping is a technique to reduce the
structural vibrations by means of placing small metallic particles
inside a cavity that is attached to the structure at location of high
vibration amplitudes. In this paper, we have presented an analytical
model to simulate the particle damping of two dimensional transient
vibrations in structure operating under high centrifugal loads. The
simulation results show that this technique remains effective as long
as the ratio of the dynamic acceleration of the structure to the applied
centrifugal load is more than 0.1. Particle damping increases with the
increase of particle to structure mass ratio. However, unlike to the
case of particle damping in the absence of centrifugal loads where
the damping efficiency strongly depends upon the size of the cavity,
here this dependence becomes very weak. Despite the simplicity of
the model, the simulation results are considerably in good agreement
with the very scarce experimental data available in the literature for
particle damping under centrifugal loads.
Abstract: We investigate sonic cues for binaural sound localization within classrooms and present a structural model for the same. Two of the primary cues for localization, interaural time difference (ITD) and interaural level difference (ILD) created between the two ears by sounds from a particular point in space, are used. Although these cues do not lend any information about the elevation of a sound source, the torso, head, and outer ear carry out elevation dependent spectral filtering of sounds before they reach the inner ear. This effect is commonly captured in head related transfer function (HRTF) which aids in resolving the ambiguity from the ITDs and ILDs alone and helps localize sounds in free space. The proposed structural model of HRTF produces well controlled horizontal as well as vertical effects. The implemented HRTF is a signal processing model which tries to mimic the physical effects of the sounds interacting with different parts of the body. The effectiveness of the method is tested by synthesizing spatial audio, in MATLAB, for use in listening tests with human subjects and is found to yield satisfactory results in comparison with existing models.
Abstract: The purpose of the study is to determine secondary prospective mathematics teachers- views related to using flash animations in mathematics lessons and to reveal how the sample presentations towards different mathematical concepts altered their views. This is a case study involving three secondary prospective mathematics teachers from a state university in Turkey. The data gathered from two semi-structural interviews. Findings revealed that these animations help understand mathematics meaningfully, relate mathematics and real world, visualization, and comprehend the importance of mathematics. The analysis of the data indicated that the sample presentations enhanced participants- views about using flash animations in mathematics lessons.
Abstract: The objective of this work was to examine the
changes in the microstructure and macro physical properties caused
by the carbonation of normalised CEM II mortar. Samples were
prepared and subjected to accelerated carbonation at 20°C, 65%
relative humidity and 20% CO2 concentration. On the microstructure
scale, the evolutions of the cumulative pore volume, pore size
distribution, and specific surface area during carbonation were
calculated from the adsorption desorption isotherms of nitrogen. We
also examined the evolution of macro physical properties such as the
porosity accessible to water, the gas permeability, and thermal
conductivity. The conflict between the results of nitrogen porosity
and water porosity indicated that the porous domains explored using
these two techniques are different and help to complementarily
evaluate the effects of carbonation. This is a multi-scale study where
results on microstructural changes can help to explain the evolution
of macro physical properties.
Abstract: The purpose of this paper is to examine the inter
relationships among various leadership branding constructs of
entrepreneurs in small and medium sized enterprises (SMEs). We
employ a quantitative structural equation modeling through a new
leadership branding engagement model comprises constructs of
leader-s or entrepreneur-s personality, branding practice and
customer engagement. The results confirm that there are significant
relationships between the three constructs and the major fit indices
indicate that the data fits the proposed model. The findings provide
insights and fill in the literature gaps on statistically validated
representation of leadership branding for SMEs across new economic
regions of Malaysia that may implicate other economic zones with
similar situations. This study extends the establishment of a
leadership branding engagement model with a new mechanism of
using leaders- personality as a predictor to branding practice and
customer engagement performance.
Abstract: As the advancement of technology, online shopping channel develops rapidly in recent years. According to the report of Taiwan Network Information Center, there are almost eighty percents of internet population shopping in online channel. Synthesizing insights from the previous research, this study develops the conceptual model to integrate Theory of Perceived Risk (TPR) and Technology Acceptance Model (TAM) to apply in online shopping. Using data collected from 637 respondents from online survey website, we use structural equation modeling to test measurement and structural models. The results suggest the need for consideration of perceived risk as an antecedent in the Technology Acceptance Model. The limitations and implications are discussed.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: Pure phase gallosilicate nitrite sodalite has been synthesized in a single step by low temperature (373 oK) hydrothermal technique. The product obtained was characterized using a combination of techniques including X-ray powder diffraction, IR, Raman spectroscopy, SEM, MAS NMR spectroscopy as well as thermogravimetry. Sodalite with an ideal composition was obtained after synthesis at 3730K and seven days duration using alkaline medium. The structural features of the Na8[GaSiO4]6(NO2)2 sodalite were investigated by IR, MAS NMR spectroscopy of 29Si and 23Na nuclei and by Reitveld refinement of X-ray powder diffraction data. The crystal structure of this sodalite has been refined in the space group P 4 3n; with a cell parameter 8.98386Å, V= 726.9 Å, (Rwp= 0.077 and Rp=0.0537) and Si-O-Ga angle is found to be 132.920 . MAS NMR study confirms complete ordering of Si and Ga in the gallosilicate framework. The surface area of single entity with stoichiometry Na8[GaSiO4]6(NO2)2 was found to be 8.083 x10-15 cm2/g.
Abstract: The presence of a vertical edge-crack within a web
plate subjected to pure bending induces local compressive stresses
about the crack which may cause tension buckling. Approximate
theoretical expressions were derived for the critical far-field tensile
stress and bending moment capacity of an edge-cracked web plate
associated with tension buckling. These expressions were validated
with finite element analyses and used to investigate the possibility of
tension buckling in web-cracked trial girders. It was found that
tension buckling is an unlikely occurrence unless the web is relatively
thin or the crack is very long.
Abstract: Turbulence of the incoming wind field is of paramount
importance to the dynamic response of civil engineering structures. Hence reliable stochastic models of the turbulence should be available from which time series can be generated for dynamic response and
structural safety analysis. In the paper an empirical cross spectral
density function for the along-wind turbulence component over the wind field area is taken as the starting point. The spectrum is spatially
discretized in terms of a Hermitian cross-spectral density matrix for the turbulence state vector which turns out not to be positive
definite. Since the succeeding state space and ARMA modelling of
the turbulence rely on the positive definiteness of the cross-spectral
density matrix, the problem with the non-positive definiteness of such
matrices is at first addressed and suitable treatments regarding it are proposed. From the adjusted positive definite cross-spectral density
matrix a frequency response matrix is constructed which determines the turbulence vector as a linear filtration of Gaussian white noise.
Finally, an accurate state space modelling method is proposed which allows selection of an appropriate model order, and estimation of a state space model for the vector turbulence process incorporating its phase spectrum in one stage, and its results are compared with a conventional ARMA modelling method.
Abstract: Integrins are a large family of multidomain α/β cell
signaling receptors. Some integrins contain an additional inserted I
domain, whose earliest expression appears to be with the chordates,
since they are observed in the urochordates Ciona intestinalis (vase
tunicate) and Halocynthia roretzi (sea pineapple), but not in integrins
of earlier diverging species. The domain-s presence is viewed as a
hallmark of integrins of higher metazoans, however in vertebrates,
there are clearly three structurally-different classes: integrins without
I domains, and two groups of integrins with I domains but separable
by the presence or absence of an additional αC helix. For example,
the αI domains in collagen-binding integrins from Osteichthyes
(bony fish) and all higher vertebrates contain the specific αC helix,
whereas the αI domains in non-collagen binding integrins from
vertebrates and the αI domains from earlier diverging urochordate
integrins, i.e. tunicates, do not. Unfortunately, within the early
chordates, there is an evolutionary gap due to extinctions between the
tunicates and cartilaginous fish. This, coupled with a knowledge gap
due to the lack of complete genomic data from surviving species,
means that the origin of collagen-binding αC-containing αI domains
remains unknown. Here, we analyzed two available genomes from
Callorhinchus milii (ghost shark/elephant shark; Chondrichthyes –
cartilaginous fish) and Petromyzon marinus (sea lamprey;
Agnathostomata), and several available Expression Sequence Tags
from two Chondrichthyes species: Raja erinacea (little skate) and
Squalus acanthias (dogfish shark); and Eptatretus burgeri (inshore
hagfish; Agnathostomata), which evolutionary reside between the
urochordates and osteichthyes. In P. marinus, we observed several
fragments coding for the αC-containing αI domain, allowing us to
shed more light on the evolution of the collagen-binding integrins.
Abstract: When dealing with safety in structures, the connections between structural components play an important role. Robustness of a structure as a whole depends both on the load- bearing capacity of the structural component and on the structures capacity to resist total failure, even though a local failure occurs in a component or a connection between components. To avoid progressive collapse it is necessary to be able to carry out a design for connections. A connection may be executed with anchors to withstand local failure of the connection in structures built with prefabricated components. For the design of these anchors, a model is developed for connections in structures performed in prefabricated autoclaved aerated concrete components. The design model takes into account the effect of anchors placed close to the edge, which may result in splitting failure. Further the model is developed to consider the effect of reinforcement diameter and anchor depth. The model is analytical and theoretically derived assuming a static equilibrium stress distribution along the anchor. The theory is compared to laboratory test, including the relevant parameters and the model is refined and theoretically argued analyzing the observed test results. The method presented can be used to improve safety in structures or even optimize the design of the connections
Abstract: Polypropylene blended with natural oil and pigment additives has been studied. Different formulations for each compound were made into polybag used for cultivation of oil palm seedlings for strength and mechanical properties studies. One group of sample was exposed under normal sunlight to initiate degradation and another group of sample was placed under shaded area for five months. All samples were tested for tensile strength to determine the degradation effects. The tensile strength of directly exposed sunlight samples and shaded area showed up to 50% and 25% degradation respectively. However, similar reduction of Young’s modulus for all samples was found for both exposures. Structural investigations were done using FTIR to detect deformation. The natural additives that were used in the studies were all natural and environmental friendly
Abstract: Despite the fact that Knowledge Sharing (KS) is very important, we found only little discussion about the reasons why people have the willingness to share knowledge at such platform even though there is no immediate benefit to the persons who contribute knowledge in it. The aim of this study is to develop an integrative understanding of the factors that support or inhibit individuals- knowledge sharing intentions in virtual communities and to find whether habit would generate people-s willingness to be involved. We apply Social Capital Theory (SCT), and we also add two dimensions for discussion: member incentive and habitual domain (HD). This research assembles the questionnaire from individuals who have experienced knowledge sharing in virtual communities, and applies survey and Structural Equation Model (SEM) to analyze the results from the questionnaires. Finally, results confirm that individuals are willing to share knowledge in virtual communities: (1) if they consider reciprocity, centrality, and have longer tenure in their field, and enjoy helping. (2) if they have the habit of sharing knowledge. This study is useful for the developers of virtual communities to insight into knowledge sharing in cyberspace.
Abstract: In this work we report the recent progresses that have been achieved by our group in the last half decade on the field of computational proteomics. Specifically, we discuss the application of Molecular Dynamics Simulations and Electronic Structure Calculations in drug design, in the clarification of the structural and dynamic properties of proteins and enzymes and in the understanding of the catalytic and inhibition mechanism of cancer-related enzymes. A set of examples illustrate the concepts and help to introduce the reader into this important and fast moving field.
Abstract: In this paper we present a substantiation of a new
Laguerre-s type iterative method for solving of a nonlinear
polynomial equations systems with real coefficients. The problems of
its implementation, including relating to the structural choice of
initial approximations, were considered. Test examples demonstrate
the effectiveness of the method at the solving of many practical
problems solving.
Abstract: In this paper, the shape design process is briefly discussed emphasizing the use of topology optimization in the conceptual design stage. The basic idea is to view feasible domains for sensitivity region concepts. In this method, the main process consists of two steps: as the design moves further inside the feasible domain using Taguchi method, and thus becoming more successful topology optimization, the sensitivity region becomes larger. In designing a double-eccentric butterfly valve, related to hydrodynamic performance and disc structure, are discussed where the use of topology optimization has proven to dramatically improve an existing design and significantly decrease the development time of a shape design. Computational Fluid Dynamics (CFD) analysis results demonstrate the validity of this approach.
Abstract: Severe acute respiratory syndrome (SARS) is a respiratory disease in humans which is caused by the SARS coronavirus. The treatment of coronavirus-associated SARS has been evolving and so far there is no consensus on an optimal regimen. The mainstream therapeutic interventions for SARS involve broad-spectrum antibiotics and supportive care, as well as antiviral agents and immunomodulatory therapy. The Protein- Ligand interaction plays a significant role in structural based drug designing. In the present work we have taken the receptor Angiotensin converting enzyme 2 and identified the drugs that are commonly used against SARS. They are Lopinavir, Ritonavir, Ribavirin, and Oseltamivir. The receptor Angiotensin converting enzyme 2 (ACE-2) was docked with above said drugs and the energy value obtained are as follows, Lopinavir (-292.3), Ritonavir (-325.6), Oseltamivir (- 229.1), Ribavirin (-208.8). Depending on the least energy value we have chosen the best two drugs out of the four conventional drugs. We tried to improve the binding efficiency and steric compatibility of the two drugs namely Ritonavir and Lopinavir. Several modifications were made to the probable functional groups (phenylic, ketonic groups in case of Ritonavir and carboxylic groups in case of Lopinavir respectively) which were interacting with the receptor molecule. Analogs were prepared by Marvin Sketch software and were docked using HEX docking software. Lopinavir analog 8 and Ritonavir analog 11 were detected with significant energy values and are probable lead molecule. It infers that some of the modified drugs are better than the original drugs. Further work can be carried out to improve the steric compatibility of the drug based upon the work done above for a more energy efficient binding of the drugs to the receptor.