Abstract: The paper is focused on the identification of limiting
environmental factors of individual industrial floors on which newly
developed polymer protection and repair systems with the use of
secondary raw materials will be used. These mainly include floors
with extreme stresses and special requirements for materials used. In
relation to the environment of a particular industrial floor, it is
necessary to ensure, for example, chemical stability, resistance to
higher temperatures, resistance to higher mechanical stress, etc. for
developed materials, which is reflected in the demands for the
developed material systems. The paper describes individual
environments and, in relation to them, also requirements for
individual components of the developed materials and for the
developed materials as a whole.
Abstract: Testability modeling is a commonly used method in
testability design and analysis of system. A dependency matrix will be
obtained from testability modeling, and we will give a quantitative
evaluation about fault detection and isolation.
Based on the dependency matrix, we can obtain the diagnosis tree.
The tree provides the procedures of the fault detection and isolation.
But the dependency matrix usually includes built-in test (BIT) and
manual test in fact. BIT runs the test automatically and is not limited
by the procedures. The method above cannot give a more efficient
diagnosis and use the advantages of the BIT.
A Comprehensive method of fault detection and isolation is
proposed. This method combines the advantages of the BIT and
Manual test by splitting the matrix. The result of the case study shows
that the method is effective.
Abstract: The quality and condition of perishable products
delivered to the market and their subsequent selling prices are
directly affected by the care taken during harvesting and handling.
Mechanical injury, in fact, occurs at all stages, from pre-harvest
operations through post-harvest handling, packing and transport to
the market. The main implications of this damage are the reduction of
the product’s quality and economical losses related to the shelf life
diminution. For most perishable products, the shelf life is relatively
short and it is typically dictated by microbial growth related to the
application of dynamic and static loads during transportation. This
paper presents the correlation between vibration levels and
microbiological growth on strawberries and woodland strawberries
and detects the presence of volatile organic compounds (VOC) in
order to develop an intelligent logistic unit capable of monitoring
VOCs using a specific sensor system. Fresh fruits were exposed to
vibrations by means of a vibrating table in a temperature-controlled
environment. Microbiological analyses were conducted on samples,
taken at different positions along the column of the crates. The values
obtained were compared with control samples not exposed to
vibrations and the results show that different positions along the
column influence the development of bacteria, yeasts and filamentous
fungi.
Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: The aim of this paper is to present the optimization
methodology developed in the frame of a Coastal Transport
Information System. The system will be used for the effective design
of coastal transportation lines and incorporates subsystems that
implement models, tools and techniques that may support the design
of improved networks. The role of the optimization and decision
subsystem is to provide the user with better and optimal scenarios
that will best fulfill any constrains, goals or requirements posed. The
complexity of the problem and the large number of parameters and
objectives involved led to the adoption of an evolutionary method
(Genetic Algorithms). The problem model and the subsystem
structure are presented in detail, and, its support for simulation is also
discussed.
Abstract: Flexible AC Transmission Systems (FACTS) is
granting a new group of advanced power electronic devices emerging
for enhancement of the power system performance. Unified Power
Flow Controller (UPFC) is a recent version of FACTS devices for
power system applications. The back-up energy supply system
incorporated with UPFC is providing a complete control of real and
reactive power at the same time and hence is competent to improve
the performance of an electrical power system. In this article, backup
energy supply unit such as superconducting magnetic energy storage
(SMES) is integrated with UPFC. In addition, comparative
exploration of UPFC–battery, UPFC–UC and UPFC–SMES
performance is evaluated through the vibrant simulation by using
MATLAB/Simulink software.
Abstract: After the internet explosion in the 90’s, technology
was immediately integrated into the school system. Technology
which symbolizes advancement in human knowledge was seen as a
setback by many educators. Efforts have been made to help stem this
erroneous believes and help educators realize the benefits of
technology and ways of implementing it in the classrooms especially
in the sciences. This advancement created a constantly expanding gap
between the pupil’s perception on the use of technology within the
learning atmosphere and the teacher’s perception and limitations
hence, the focus of this paper is on the need to refocus on the use of
Science and Technology in enhancing children’s potentials in
learning at school especially in Science for sustainable development
in Nigeria. The paper recommended measures for facilitating the
sustenance of science and technology in Nigerian schools so as to
enhance the potentials of our children in Science and Technology for
a better tomorrow.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: This paper describes the issues relating to the role of
the flash flood early warning system provided by the Malaysian
Government to the communities in Malaysia, specifically during the
flash flood disaster in the Cameron Highlands, Malaysia. Normally,
flash flood disasters can occur as a result of heavy rainfall in an area,
and that water may possibly cause flooding via streams or narrow
channels. The focus of this study is the flash flood disaster which
occurred on 23 October 2013 in the Cameron Highlands, and as a
result the Sungai Bertam overflowed after the release of water from
the Sultan Abu Bakar Dam. This release of water from the dam
caused flash flooding which led to damage to properties and also the
death of residents and livestock in the area. Therefore, the effort of
this study is to identify the perceptions of the flash flood victims on
the role of the flash flood early warning system. For the purposes of
this study, data were gathered through face-to-face interviews from
those flood victims who were willing to participate in this study. This
approach helped the researcher to glean in-depth information about
their feelings and perceptions of the role of the flash flood early
warning system offered by the government. The data were analysed
descriptively and the findings show that the respondents of 22 flood
victims believe strongly that the flash flood early warning system was
confusing and dysfunctional, and communities had failed to response
positively to it. Therefore, most of the communities were not well
prepared for the releasing of water from the dam which caused
property damage, and 3 people were killed in the Cameron Highland
flash flood disaster.
Abstract: In this study, polycaprolactone (PCL) was dissolved
in chloroform:ethanol solvent system at a concentration of 18 w/v %.
1, 2, 4, and 6 droplets of formic acid were added to the prepared 10ml
PCL-chloroform:ethanol solutions separately. Fibrous webs were
produced by electrospinning technique based on the horizontal
working principle. Morphology of the webs was investigated by
using scanning electron microscopy (SEM) whereas fiber diameters
were measured by Image J Software System. The effect of formic
acid addition to the mostly used chloroform solvent on fiber
morphology was examined.
Results indicate that there is a distinct fall in fiber diameter with
the addition of formic acid drops. The average fiber diameter was
measured as 2.22μm in PCL /chloroform:ethanol solution system. On
the other hand, 328nm and 256 nm average fiber diameters were
measured for the samples of 4 drops and 6 drops formic acid added.
This study offers alternative solvent systems to produce nanoscaled,
nontoxic PCL fibrous webs by electrospinning technique.
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: The flora of Bozdağ (Konya) and its surroundings
were investigated between 2003 and 2005 years; 700 herbarium
specimens belonging to 482 taxa, 257 genera and 57 families were
collected and identified from the area. The families which have the
most taxa in research area are Asteraceae 67 (14.0%), Fabaceae 60
(12.6%), Lamiaceae 57 (11.9%), Brassicaceae 34 (7.1%), Poaceae
30 (6.3%), Rosaceae 24 (5.0%), Caryophyllaceae 23 (4.8%),
Liliaceae 19 (4.0%), Boraginaceae 17 (3.6%), and Apiaceae 13
(2.7%).
The research area is in the district of Konya and is in the B4
square according to the Grid System. The phytogeographic elements
are represented in the study area as follows; Irano-Turanian 91
(18.9%), Mediterranean 72 (14.9%), Euro-Siberian 21 (4.3%). The
phytogeographic regions of 273 (56.6%) taxa are either multi-regional
or unknown. The number of endemic taxa is 79 (16.3%).
Abstract: In this paper, the exergy analysis of vapor absorption
refrigeration system using LiBr-H2O as working fluid is carried out
with the modified Gouy-Stodola approach rather than the classical
Gouy-Stodola equation and effect of varying input parameters is also
studied on the performance of the system. As the modified approach
uses the concept of effective temperature, the mathematical
expressions for effective temperature have been formulated and
calculated for each component of the system. Various constraints and
equations are used to develop program in EES to solve these
equations. The main aim of this analysis is to determine the
performance of the system and the components having major
irreversible loss. Results show that exergy destruction rate is
considerable in absorber and generator followed by evaporator and
condenser. There is an increase in exergy destruction in generator,
absorber and condenser and decrease in the evaporator by the
modified approach as compared to the conventional approach. The
value of exergy determined by the modified Gouy-Stodola equation
deviates maximum i.e. 26% in the generator as compared to the
exergy calculated by the classical Gouy-Stodola method.
Abstract: In this article we will study the elliptic curve defined
over the ring An and we define the mathematical operations of ECC,
which provides a high security and advantage for wireless
applications compared to other asymmetric key cryptosystem.
Abstract: An innovative concept called “Flexy-Energy” is developing at 2iE. This concept aims to produce electricity at lower cost by smartly mix different available energy sources in accordance to the load profile of the region. With a higher solar irradiation and due to the fact that Diesel generator are massively used in sub-Saharan rural areas, PV/Diesel hybrid systems could be a good application of this concept and a good solution to electrify this region, provided they are reliable, cost effective and economically attractive to investors. Presentation of the developed approach is the aims of this paper. The PV/Diesel hybrid system designed consists to produce electricity and/or heat from a coupling between Diesel Diesel generators and PV panels without batteries storage, while ensuring the substitution of gasoil by bio-fuels available in the area where the system will be installed. The optimal design of this system is based on his technical performances; the Life Cycle Cost (LCC) and Levelized Cost of Energy are developed and use as economic criteria. The Net Present Value (NPV), the internal rate of return (IRR) and the discounted payback (DPB) are also evaluated according to dual electricity pricing (in sunny and unsunny hours). The PV/Diesel hybrid system obtained is compared to the standalone Diesel Diesel generators. The approach carried out in this paper has been applied to Siby village in Mali (Latitude 12 ° 23'N 8 ° 20'W) with 295 kWh as daily demand.This approach provides optimal physical characteristics (size of the components, number of component) and dynamical characteristics in real time (number of Diesel generator on, their load rate, fuel specific consumptions, and PV penetration rate) of the system. The system obtained is slightly cost effective; but could be improved with optimized tariffing strategies.
Abstract: This paper attempts to define the validity domain of
LSDP (Loop Shaping Design Procedure) controller system, by
determining the suitable uncertainty region, so that linear system be
stable. Indeed the LSDP controller cannot provide stability for any
perturbed system. For this, we will use the gap metric tool that is
introduced into the control literature for studying robustness
properties of feedback systems with uncertainty. A 2nd order electric
linear system example is given to define the validity domain of LSDP
controller and effectiveness gap metric.
Abstract: Real bronchial tree is very complicated piping system.
Analysis of flow and pressure losses in this system is very difficult.
Due to the complex geometry and the very small size in the lower
generations is examination by CFD possible only in the central part
of bronchial tree. For specify the pressure losses of lower generations
is necessary to provide a mathematical equation. Determination of
mathematical formulas for calculation of pressure losses in the real
lungs is time consuming and inefficient process due to its complexity
and diversity. For these calculations is necessary to slightly simplify
the geometry of lungs (same cross-section over the length of
individual generation) or use one of the idealized models of lungs
(Horsfield, Weibel). The article compares the values of pressure
losses obtained from CFD simulation of air flow in the central part of
the real bronchial tree with the values calculated in a slightly
simplified real lungs by using a mathematical relationship derived
from the Bernoulli and continuity equations. The aim of the article is
to analyse the accuracy of the analytical method and its possibility of
use for the calculation of pressure losses in lower generations, which
is difficult to solve by numerical method due to the small geometry.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: In this paper, a new design of spherical robotic system
based on the concepts of gimbal structure and gyro dynamics is
presented. Robots equipped with multiple wheels and complex
steering mechanics may increase the weight and degrade the energy
transmission efficiency. In addition, the wheeled and legged robots are
relatively vulnerable to lateral impact and lack of lateral mobility.
Therefore, the proposed robotic design uses a spherical shell as the
main body for ground locomotion, instead of using wheel devices.
Three spherical shells are structured in a similar way to a gimbal
device and rotate like a gyro system. The design and mechanism of the
proposed robotic system is introduced. In addition, preliminary results
of the dynamic model based on the principles of planar rigid body
kinematics and Lagrangian equation are included. Simulation results
and rig construction are presented to verify the concepts.
Abstract: Innovation plays an important role in economic
growth and development. Evolutionary economics has entrepreneurs
at the centre of the innovation system, but includes all other
participants as contributors to the performance of the innovation
system. Education and training institutions, one of the participants in
the innovation system, contributes in different ways to human capital.
The gap in literature on the competence building as part of human
capital in the analysis of innovation systems is addressed in this
paper. The Mpumalanga Province of South Africa is used as a case
study. It was found that the absence of a university, the level of
education, the quality and performance in the education sector and
the condition of the education infrastructure have not been conducive
to learning.