Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: In this paper we used data mining techniques to
identify outlier patients who are using large amount of drugs over a
long period of time. Any healthcare or health insurance system
should deal with the quantities of drugs utilized by chronic diseases
patients. In Kingdom of Bahrain, about 20% of health budget is spent
on medications. For the managers of healthcare systems, there is no
enough information about the ways of drug utilization by chronic
diseases patients, is there any misuse or is there outliers patients. In
this work, which has been done in cooperation with information
department in the Bahrain Defence Force hospital; we select the data
for Cardiac patients in the period starting from 1/1/2008 to
December 31/12/2008 to be the data for the model in this paper. We
used three techniques for finding the drug utilization for cardiac
patients. First we applied a clustering technique, followed by
measuring of clustering validity, and finally we applied a decision
tree as classification algorithm. The clustering results is divided into
three clusters according to the drug utilization, for 1603 patients, who
received 15,806 prescriptions during this period can be partitioned
into three groups, where 23 patients (2.59%) who received 1316
prescriptions (8.32%) are classified to be outliers. The classification
algorithm shows that the use of average drug utilization and the age,
and the gender of the patient can be considered to be the main
predictive factors in the induced model.
Abstract: This paper presents a wrap-around view system with 4
smart cameras module and remote motion mobile robot control equipped with smart camera module system. The two-level scheme for
remote motion control with smart-pad(IPAD) is introduced on this
paper. In the low-level, the wrap-around view system is controlled or operated to keep the reference points lying around top view image
plane. On the higher level, a robot image based motion controller is utilized to drive the mobile platform to reach the desired position or
track the desired motion planning through image feature feedback. The
design wrap-around view system equipped on presents such advantages as follows: 1) a satisfactory solution for the FOV and affine
problem; 2) free of any complex and constraint with robot pose. The performance of the wrap-around view equipped on mobile robot
remote control is proven by experimental results.
Abstract: This paper presents the decoder design for the single error correcting and double error detecting code proposed by the authors in an earlier paper. The speed of error detection and correction of a code is largely dependent upon the associated encoder and decoder circuits. The complexity and the speed of such circuits are determined by the number of 1?s in the parity check matrix (PCM). The number of 1?s in the parity check matrix for the code proposed by the authors are fewer than in any currently known single error correcting/double error detecting code. This results in simplified encoding and decoding circuitry for error detection and correction.
Abstract: This paper attempts to establish the fact that Multi
State Network Classification is essential for performance
enhancement of Transport protocols over Satellite based Networks. A
model to classify Multi State network condition taking into
consideration both congestion and channel error is evolved. In order
to arrive at such a model an analysis of the impact of congestion and
channel error on RTT values has been carried out using ns2. The
analysis results are also reported in the paper. The inference drawn
from this analysis is used to develop a novel statistical RTT based
model for multi state network classification.
An Adaptive Multi State Proactive Transport Protocol consisting
of Proactive Slow Start, State based Error Recovery, Timeout Action
and Proactive Reduction is proposed which uses the multi state
network state classification model. This paper also confirms through
detail simulation and analysis that a prior knowledge about the
overall characteristics of the network helps in enhancing the
performance of the protocol over satellite channel which is
significantly affected due to channel noise and congestion.
The necessary augmentation of ns2 simulator is done for
simulating the multi state network classification logic. This
simulation has been used in detail evaluation of the protocol under
varied levels of congestion and channel noise. The performance
enhancement of this protocol with reference to established protocols
namely TCP SACK and Vegas has been discussed. The results as
discussed in this paper clearly reveal that the proposed protocol
always outperforms its peers and show a significant improvement in
very high error conditions as envisaged in the design of the protocol.
Abstract: A mathematical model of the respiratory system is
introduced in this study. Geometrical dimensions of the respiratory
system were used to compute the acoustic properties of the
respiratory system using the electro-acoustic analogy. The effect of
the geometrical proportions of the respiratory system is observed in
the paper.
Abstract: An appropriate method for fault identification and classification on extra high voltage transmission line using discrete wavelet transform is proposed in this paper. The sharp variations of the generated short circuit transient signals which are recorded at the sending end of the transmission line are adopted to identify the fault. The threshold values involve fault classification and these are done on the basis of the multiresolution analysis. A comparative study of the performance is also presented for Discrete Fourier Transform (DFT) based Artificial Neural Network (ANN) and Discrete Wavelet Transform (DWT). The results prove that the proposed method is an effective and efficient one in obtaining the accurate result within short duration of time by using Daubechies 4 and 9. Simulation of the power system is done using MATLAB.
Abstract: A virtual collaborative classroom was created at East Carolina University, using videoconference technology via regular internet to bring students from 18 different countries, 2 at a time, to the ECU classroom in real time to learn about each other-s culture. Students from two countries are partnered one on one, they meet for 4-5 weeks, and submit a joint paper. Then the same process is repeated for two other countries. Lectures and student discussions are managed with pre-determined topics and questions. Classes are conducted in English and reading assignments are placed on the website. Administratively all partners are independent, students pay fees and get credits at their home institution. Familiarity with technology, knowledge in cultural understanding and attitude change were assessed, only attitude changes are reported in this paper. After taking this course, all students stated their comfort level in working with, and their desire to interact with, culturally different others grew stronger and their xenophobia and isolationist attitudes decreased.
Abstract: Images of human iris contain specular highlights due
to the reflective properties of the cornea. This corneal reflection
causes many errors not only in iris and pupil center estimation but
also to locate iris and pupil boundaries especially for methods that
use active contour. Each iris recognition system has four steps:
Segmentation, Normalization, Encoding and Matching. In order to
address the corneal reflection, a novel reflection removal method is
proposed in this paper. Comparative experiments of two existing
methods for reflection removal method are evaluated on CASIA iris
image databases V3. The experimental results reveal that the
proposed algorithm provides higher performance in reflection
removal.
Abstract: An efficient architecture for low jitter All Digital
Phase Locked Loop (ADPLL) suitable for high speed SoC
applications is presented in this paper. The ADPLL is designed using
standard cells and described by Hardware Description Language
(HDL). The ADPLL implemented in a 90 nm CMOS process can
operate from 10 to 200 MHz and achieve worst case frequency
acquisition in 14 reference clock cycles. The simulation result shows
that PLL has cycle to cycle jitter of 164 ps and period jitter of 100 ps
at 100MHz. Since the digitally controlled oscillator (DCO) can
achieve both high resolution and wide frequency range, it can meet
the demands of system-level integration. The proposed ADPLL can
easily be ported to different processes in a short time. Thus, it can
reduce the design time and design complexity of the ADPLL, making
it very suitable for System-on-Chip (SoC) applications.
Abstract: In order to study pressed pile test and ultimate bearing
capacity character of large-diameter steel pipe pile, based on two high-piled wharfs of Zhanjiang Port, pressed pile test and numerical simulation of three large-diameter steel pipe piles are analyzed in this
paper. Anchored pile method is used to pressed pile test, and the
curves of Q-s and ultimate bearing capacity are attained. Then the three piles are numerically simulated by ABAQUS, and results of numerical simulation and those of field test are comparatively analyzed. The results show that settlement value of numerical
simulation is larger than that of field test in the process of loading, the difference value is widening with the increasing of load, and the
ultimate difference value of settlement is 20% to 30%.
Abstract: In this paper, a new technique of signal detection has been proposed for detecting the orthogonal frequency-division multiplexing (OFDM) signal in the presence of nonlinear distortion.There are several advantages of OFDM communications system.However, one of the existing problems is remain considered as the nonlinear distortion generated by high-power-amplifier at the transmitter end due to the large dynamic range of an OFDM signal. The proposed method is the maximum likelihood detection with the symbol estimation. When the training data are available, the neural network has been used to learn the characteristic of received signal and to estimate the new positions of the transmitted symbol which are provided to the maximum likelihood detector. Resulting in the system performance, the nonlinear distortions of a traveling wave tube amplifier with OFDM signal are considered in this paper.Simulation results of the bit-error-rate performance are obtained with 16-QAM OFDM systems.
Abstract: This paper presents a system overview of Mobile to Server Face Recognition, which is a face recognition application developed specifically for mobile phones. Images taken from mobile phone cameras lack of quality due to the low resolution of the cameras. Thus, a prototype is developed to experiment the chosen method. However, this paper shows a result of system backbone without the face recognition functionality. The result demonstrated in this paper indicates that the interaction between mobile phones and server is successfully working. The result shown before the database is completely ready. The system testing is currently going on using real images and a mock-up database to test the functionality of the face recognition algorithm used in this system. An overview of the whole system including screenshots and system flow-chart are presented in this paper. This paper also presents the inspiration or motivation and the justification in developing this system.
Abstract: There are three approaches to complete Bayesian
Network (BN) model construction: total expert-centred, total datacentred,
and semi data-centred. These three approaches constitute the
basis of the empirical investigation undertaken and reported in this
paper. The objective is to determine, amongst these three
approaches, which is the optimal approach for the construction of a
BN-based model for the performance assessment of students-
laboratory work in a virtual electronic laboratory environment. BN
models were constructed using all three approaches, with respect to
the focus domain, and compared using a set of optimality criteria. In
addition, the impact of the size and source of the training, on the
performance of total data-centred and semi data-centred models was
investigated. The results of the investigation provide additional
insight for BN model constructors and contribute to literature
providing supportive evidence for the conceptual feasibility and
efficiency of structure and parameter learning from data. In addition,
the results highlight other interesting themes.
Abstract: In view of their importance and usefulness in reliability theory and probability distributions, several generalizations of the inverse Gaussian distribution and the Krtzel function are investigated in recent years. This has motivated the authors to introduce and study a new generalization of the inverse Gaussian distribution and the Krtzel function associated with a product of a Bessel function of the third kind )(zKQ and a Z - Fox-Wright generalized hyper geometric function introduced in this paper. The introduced function turns out to be a unified gamma-type function. Its incomplete forms are also discussed. Several properties of this gamma-type function are obtained. By means of this generalized function, we introduce a generalization of inverse Gaussian distribution, which is useful in reliability analysis, diffusion processes, and radio techniques etc. The inverse Gaussian distribution thus introduced also provides a generalization of the Krtzel function. Some basic statistical functions associated with this probability density function, such as moments, the Mellin transform, the moment generating function, the hazard rate function, and the mean residue life function are also obtained.KeywordsFox-Wright function, Inverse Gaussian distribution, Krtzel function & Bessel function of the third kind.
Abstract: Property investment in the real estate industry has a
high risk due to the uncertainty factors that will affect the decisions
made and high cost. Analytic hierarchy process has existed for some
time in which referred to an expert-s opinion to measure the
uncertainty of the risk factors for the risk analysis. Therefore,
different level of experts- experiences will create different opinion
and lead to the conflict among the experts in the field. The objective
of this paper is to propose a new technique to measure the uncertainty
of the risk factors based on multidimensional data model and data
mining techniques as deterministic approach. The propose technique
consist of a basic framework which includes four modules: user,
technology, end-user access tools and applications. The property
investment risk analysis defines as a micro level analysis as the
features of the property will be considered in the analysis in this
paper.
Abstract: The damage tolerance behavior of integrally and
conventional stiffened panel is investigated based on the fracture
mechanics and finite element analysis. The load bearing capability
and crack growth characteristic of both types of the stiffened panels
having same configuration subjected to distributed tensile load is
examined in this paper. A fourteen-stringer stiffened panel is
analyzed for a central skin crack propagating towards the adjacent
stringers. Stress intensity factors and fatigue crack propagation rates
of both types of the stiffened panels are then compared. The analysis
results show that integral stiffening causes higher stress intensity
factor than conventional stiffened panel as the crack tip passes
through the stringer and the integrally stiffened panel has less load
bearing capability than the riveted stiffened panel.
Abstract: Structural behavior of ring stiffened thick walled
cylinders made of functionally graded materials (FGMs) is
investigated in this paper. Functionally graded materials are inhomogeneous composites which are usually made from a mixture
of metal and ceramic. The gradient compositional variation of the
constituents from one surface to the other provides an elegant solution to the problem of high transverse shear stresses that are
induced when two dissimilar materials with large differences in material properties are bonded. FGM formation of the cylinder is
modeled by power-law exponent and the variation of characteristics is supposed to be in radial direction.
A finite element formulation is derived for the analysis. According to the property variation of the constituent materials in the radial
direction of the wall, it is not convenient to use conventional elements to model and analyze the structure of the stiffened FGM
cylinders. In this paper a new cylindrical super-element is used to model the finite element formulation and analyze the static and
modal behavior of stiffened FGM thick walled cylinders. By using
this super-element the number of elements, which are needed for
modeling, will reduce significantly and the process time is less in comparison with conventional finite element formulations. Results for static and modal analysis are evaluated and verified by
comparison to finite element formulation with conventional
elements. Comparison indicates a good conformity between results.
Abstract: A general stochastic spatial MIMO channel model is
proposed for evaluating various MIMO techniques in this paper. It can
generate MIMO channels complying with various MIMO
configurations such as smart antenna, spatial diversity and spatial
multiplexing. The modeling method produces the stochastic fading
involving delay spread, Doppler spread, DOA (direction of arrival),
AS (angle spread), PAS (power azimuth Spectrum) of the scatterers,
antenna spacing and the wavelength. It can be applied in various
MIMO technique researches flexibly with low computing complexity.