Abstract: This entry concerned with dense silica bricks
microstructure was produced as a part of a project within the
Technology Agency of the Czech Republic which is being
implemented in cooperation of the biggest producer of refractories
the P-D Refractories CZ company with the research organisation
Brno University of Technology. The paper is focused on the
influence of mixture homogenisation and the influence of grain size
of the mineraliser on the resulting utility properties of the material as
well as its microstructure. It has a decisive influence on the durability
of the material in a building structure. This paper is a continuation of
a previously published study dealing with the suitability of various
types of mineralising agents in terms of density, strength and mineral
composition of silica brick.
The entry describes the influence of the method of mixture
homogenisation and the influence of granulometry of the applied Femineralising
agent on the resulting silica microstructure. Porosity,
density, phase composition and microstructure of the experimentally
prepared silica bricks samples were examined and the results were
discussed in context with the technology of homogenisation and
firing temperature used. The properties of silica bricks samples were
compared to the sample without any Fe-mineraliser.
Abstract: Heating, cooling and lighting appliances in buildings
account for more than one third of the world’s primary energy
demand. Therefore, main components of the building heating systems
play an essential role in terms of energy consumption. In this context,
efficient energy and exergy utilization in HVAC-R systems has been
very essential, especially in developing energy policies towards
increasing efficiencies. The main objective of the present study is to
assess the performance of a family house with a volume of 326.7 m3
and a net floor area of 121 m2, located in the city of Izmir, Turkey in
terms of energetic, exergetic and sustainability aspects. The indoor
and exterior air temperatures are taken as 20°C and 1°C, respectively.
In the analysis and assessment, various metrics (indices or indicators)
such as exergetic efficiency, exergy flexibility ratio and sustainability
index are utilized. Two heating options (Case 1: condensing boiler
and Case 2: air heat pump) are considered for comparison purposes.
The total heat loss rate of the family house is determined to be
3770.72 W. The overall energy efficiencies of the studied cases are
calculated to be 49.4% for Case 1 and 54.7% for Case 2. The overall
exergy efficiencies, the flexibility factor and the sustainability index
of Cases 1 and 2 are computed to be around 3.3%, 0.17 and 1.034,
respectively.
Abstract: Application of hulls processing technologies, based on high-concentrated energy sources (laser and plasma technologies), allow improve shipbuilding production. It is typical for high-speed vessels construction using steel and aluminum alloys with high precision hulls required. Report describes high-performance technologies for plasma welding (using direct current of reversed polarity), laser, and hybrid laser-arc welding of hulls structures developed by JSC “SSTC”
Abstract: Disasters are quite experienced in our days. They are
caused by floods, landslides, and building fires that is the main
objective of this study. To cope with these unexpected events,
precautions must be taken to protect human lives. The emphasis on
disposal work focuses on the resolution of the evacuation problem in
case of no-notice disaster. The problem of evacuation is listed as a
dynamic network flow problem. Particularly, we model the
evacuation problem as an earliest arrival flow problem with load
dependent transit time. This problem is classified as NP-Hard. Our
challenge here is to propose a metaheuristic solution for solving the
evacuation problem. We define our objective as the maximization of
evacuees during earliest periods of a time horizon T. The objective
provides the evacuation of persons as soon as possible. We
performed an experimental study on emergency evacuation from the
tunisian children’s hospital. This work prompts us to look for
evacuation plans corresponding to several situations where the
network dynamically changes.
Abstract: Construction in Finland is focusing increasingly on
renovation instead of conventional new construction, and this trend
will continue to grow in the coming years and decades. Renovation of
the large number of suburban residential apartment buildings built in
the 1960s and 1970s poses a particular challenge. However,
renovation projects are demanding for the residents of these
buildings, since they usually are uninitiated in construction issues. On
the other hand, renovation projects generally apply the operating
models of new construction.
Nevertheless, the residents of an existing residential apartment
building are some of the best experts on the site. Thus, in this
research project we applied a relational model in developing and
testing at case sites a planning process that employs interactive
planning methods. Current residents, housing company managers, the
city zoning manager, the contractor’s and prefab element supplier’s
representatives, professional designers and researchers all took part in
the planning. The entire interactive planning process progressed
phase by phase as the participants’ and designers’ concerted
discussion and ideation process, so that the end result was a
renovation plan desired by the residents.
Abstract: There is an essential need for obtaining the mathematical representation of fish body undulations, which can be used for designing and building new innovative types of marine propulsion systems with less environmental impact. This research work presents a case study to derive the mathematical model for fish body movement. Observation and capturing image methods were used in this study in order to obtain a mathematical representation of Clariasbatrachus fish (catfish). An experiment was conducted by using an aquarium with dimension 0.609 m x 0.304 m x 0.304 m, and a 0.5 m ruler was attached at the base of the aquarium. Progressive Scan Monochrome Camera was positioned at 1.8 m above the base of the aquarium to provide swimming sequences. Seven points were marked on the fish body using white marker to indicate the fish movement and measuring the amplitude of undulation. Images from video recordings (20 frames/s) were analyzed frame by frame using local coordinate system, with time interval 0.05 s. The amplitudes of undulations were obtained for image analysis from each point that has been marked on fish body. A graph of amplitude of undulations versus time was plotted by using computer to derive a mathematical fit. The function for the graph is polynomial with nine orders.
Abstract: The use of low quality concrete has been identified as one of the main causes of the incessant collapse of buildings in Nigeria. Emphasis has been on the use of poor quality aggregates, poor workmanship and the use of lean concrete mix with low cement quantity as the reasons for the low quality of concrete used for building construction in Nigeria. Surveys conducted revealed that in the construction of most privately owned buildings where concrete trial mixes and concrete compressive strength quality assurance tests are not conducted, concretes used for building constructions are produced using the 1:2:4 mix ratio irrespective of the cement grade/strength class. In this paper, the possible role of the use of inappropriate cement grade/strength class as a cause of the incessant collapse of building in Nigeria is investigated. Investigation revealed that the compressive strengths of concrete cubes produced with Portland-limestone cement grade 32.5 using 1:2:4 and 1:1.5:3 mix ratios are less than the 25MPa and 30MPa cube strengths generally recommended for building superstructures and foundations respectively. Conversely, the compressive strengths of concrete cubes produced with Portland-limestone cement grade 42.5 using 1:2:4 and 1:1.5:3 mix ratios exceed the 25MPa and 30MPa generally recommended for building superstructures and foundations respectively. Thus, it can be concluded that the use of inappropriate cement grade (Portland-limestone cement grade 32.5), particularly for the construction of building foundations is a potential cause of the incessant collapse of buildings in Nigeria. It is recommended that the Standards Organisation of Nigeria should embark on creating awareness for Nigerians, particularly, the home owners and the roadside craftsmen that Portland-limestone cement grade 32.5 should not be used for the construction of building load-carrying members, particularly, building foundations in order to reduce the incessant incidence of collapsed building.
Abstract: The objectives of the research are to study patterns of fire location distribution and develop techniques of Geographic Information System application in fire risk assessment for fire planning and management. Fire risk assessment was based on two factors: the vulnerability factor such as building material types, building height, building density and capacity for mitigation factor such as accessibility by road, distance to fire station, distance to hydrants and it was obtained from four groups of stakeholders including firemen, city planners, local government officers and local residents. Factors obtained from all stakeholders were converted into Raster data of GIS and then were superimposed on the data in order to prepare fire risk map of the area showing level of fire risk ranging from high to low. The level of fire risk was obtained from weighted mean of each factor based on the stakeholders. Weighted mean for each factor was obtained by Analytical Hierarchy Analysis.
Abstract: The paper gives basic information on application of
rotation bending for manufacturing ship hull parts from steel plates
and on MGPS machines, employed for this purpose.
Abstract: Sustainable tall buildings that provide comfortable,
healthy and efficient indoor environments are clearly desirable as the
densification of living and working space for the world’s increasing
population proceeds. For environmental concerns, these buildings
must also be energy efficient. One component of these tasks is the
provision of indoor air quality and thermal comfort, which can be
enhanced with natural ventilation by the supply of fresh air. Working
spaces can only be naturally ventilated with connections to the
outdoors utilizing operable windows, double facades, ventilation
stacks, balconies, patios, terraces and skygardens. Large amounts of
fresh air can be provided to the indoor spaces without mechanical
air-conditioning systems, which are widely employed in
contemporary tall buildings.
This paper tends to present the concept of natural ventilation for
sustainable tall office buildings in order to achieve healthy and
comfortable working spaces, as well as energy efficient
environments. Initially the historical evolution of ventilation
strategies for tall buildings is presented, beginning with natural
ventilation and continuing with the introduction of mechanical airconditioning
systems. Then the emergence of natural ventilation due
to the health and environmental concerns in tall buildings is handled,
and the strategies for implementing this strategy are revealed. In the
next section, a number of case studies that utilize this strategy are
investigated. Finally, how tall office buildings can benefit from this
strategy is discussed.
Abstract: Sustainability, being the urgent issue of our time, is
closely related with the innovations in technology. Nanotechnology
(NT), although not a new science, can be regarded relatively a new
science for buildings with brand new materials and applications. This
paper tends to give a research review of current and near future
applications of nanotechnology (NT) for achieving high-performance
and healthy buildings for a sustainable future. In the introduction, the
driving forces for the sustainability of construction industry are
explained. Then, the term NT is defined, and significance of
innovations in NT for a sustainable construction industry is revealed.
After presenting the application areas of NT and nanomaterials for
buildings with a number of cases, challenges in the adoption of this
technology are put forward, and finally the impacts of nanoparticles
and nanomaterials on human health and environment are discussed.
Abstract: This paper deals with a proposal of a new
methodology for durability assessment of solidification product for
its safe further use. The new methodology is based on a review of the
current state of assessment of treated waste in Czech Republic and
abroad. The aim of the paper is to propose an optimal evaluation
methodology for verifying properties of solidification product to
ensure its safe further use in building industry.
Abstract: Tsunami early detection and warning systems have proved to be of ultimate importance, especially after the destructive tsunami that hit Japan in March 2012. Such systems are crucial to inform the authorities of any risk of a tsunami and of the degree of its danger in order to make the right decision and notify the public of the actions they need to take to save their lives. The purpose of this research is to enhance existing tsunami detection and warning systems. We first propose an automated and miniaturized model of an early tsunami detection and warning system. The model for the operation of a tsunami warning system is simulated using the data acquisition toolbox of Matlab and measurements acquired from specified internet pages due to the lack of the required real-life sensors, both seismic and hydrologic, and building a graphical user interface for the system. In the second phase of this work, we implement various satellite image filtering schemes to enhance the acquired synthetic aperture radar images of the tsunami affected region that are masked by speckle noise. This enables us to conduct a post-tsunami damage extent study and calculate the percentage damage. We conclude by proposing improvements to the existing telecommunication infrastructure of existing warning tsunami systems using a migration to IP-based networks and fiber optics links.
Abstract: In order to respond the human needs, all regional, social, and economical factors are available to gain residents’ comfort and ideal architecture. There is no doubt the thermal comfort has to satisfy people not only for daily and physical activities but also creating pleasant area for mental activities and relaxing. It costs energy and increases greenhouse gas emissions.
Reducing energy use in buildings is a critical component of meeting carbon reduction commitments. Hence housing design represents a major opportunity to cut energy use and CO2 emissions.
In terms of energy efficiency, it is vital to propose and research modern design methods for buildings however vernacular architecture techniques are proven empirical existing practices which have to be considered. This research tries to compare two architectural solution were proposed by Persian vernacular architecture, to achieve energy efficiency in hot areas.
The aim of this research is to analyze two forms of traditional Persian architecture in different locations in order to develop a systematic research and sustainable technologies on adaptation to contemporary living standards.
Abstract: Both knowledge economy and sustainable development are considered key dimensions in the policy action lines of many developed and developing countries. In this context, universities and other higher education institutes have a vital role in developing and sustaining wellbeing communities.
In this paper, the authors’ aim is to address the links between the concepts of innovation and entrepreneurial capacity and knowledge economy, and to utilize the approach of intellectual capital development in building a sustainable knowledge economy.
The paper will contribute to two discourses:
Developing a common understanding of the intersection aspects between the three concepts: Knowledge economy, Innovation and entrepreneurial system, and sustainable development.
Paving the road towards developing an integrated multidimensional framework for sustainable knowledge economy.
Abstract: Farmers are in need of regular and relevant information relating to new technologies. Production of extension materials has been found to be useful in facilitating the process. Extension materials help to provide information to reach large numbers of farmers quickly and economically. However, as good as extension materials are, previous materials produced are not used by farmers. The reasons for this include lack of involvement of farmers in the production of the extension materials, most of the extension materials are not relevant to the farmers’ environments, the agricultural extension agents lack capacity to prepare the materials, and many extension agents lack commitment. These problems led to this innovative capacity building of extension agents. This innovative approach involves five stages. The first stage is the diagnostic survey of farmers’ environment to collect useful information. The second stage is the development and production of draft extension materials. The third stage is the field testing and evaluation of draft materials by the same famers that were involved at the diagnostic stage. The fourth stage is the revision of the draft extension materials by incorporating suggestions from farmers. The fifth stage is the action plans. This process improves the capacity of agricultural extension agents in the preparation of extension materials and also promotes engagement of farmers and beneficiaries in the process. The process also makes farmers assume some level of ownership of the exercise and the extension materials.
Abstract: Outrigger-braced wall systems are commonly used to provide high rise buildings with the required lateral stiffness for wind and earthquake resistance. The existence of outriggers adds to the stiffness and strength of walls as reported by several studies. The effects of different parameters on the elasto-plastic dynamic behavior of outrigger-braced wall systems to earthquakes are investigated in this study. Parameters investigated include outrigger stiffness, concrete strength, and reinforcement arrangement as the main design parameters in wall design. In addition to being significantly affect the wall behavior, such parameters may lead to the change of failure mode and the delay of crack propagation and consequently failure as the wall is excited by earthquakes. Bi-linear stress-strain relation for concrete with limited tensile strength and truss members with bi-linear stress-strain relation for reinforcement were used in the finite element analysis of the problem. The famous earthquake record, El-Centro, 1940 is used in the study. Emphasize was given to the lateral drift, normal stresses and crack pattern as behavior controlling determinants. Results indicated significant effect of the studied parameters such that stiffer outrigger, higher grade concrete and concentrating the reinforcement at wall edges enhance the behavior of the system. Concrete stresses and cracking behavior are too much enhanced while less drift improvements are observed.
Abstract: This study analyzes the crisis management and image repair strategies during the crisis of Mahidol Wittayanusorn School (MWIT) library burning. The library of this school was burned by a 16-year-old-male student on June 6th, 2010. This student blamed the school that the lesson was difficult, and other students were selfish. Although no one was in the building during the fire, it had caused damage to the building, books and electronic supplies around 130 million bahts (4.4 million USD). This event aroused many discourses arguing about the education system and morality. The strategies which were used during crisis were denial, shift the blame, bolstering, minimization, and uncertainty reduction. The results of using these strategies appeared after the crisis. That was the numbers of new students, who registered for the examination to get into this school in the later years, have remained the same.
Abstract: In this paper, we propose an optimization technique
that can be used to optimize the placements of reference nodes and
improve the location determination performance for the multi-floor
building. The proposed technique is based on Simulated Annealing
algorithm (SA) and is called MSMR-M. The performance study in
this work is based on simulation. We compare other node-placement
techniques found in the literature with the optimal node-placement
solutions obtained from our optimization. The results show that using
the optimal node-placement obtained by our proposed technique can
improve the positioning error distances up to 20% better than those of
the other techniques. The proposed technique can provide an average
error distance within 1.42 meters.
Abstract: In recent years, the introduction of Pre Engineered Building (PEB) concept in the design of structures has helped in optimizing design. The adoptability of PEB in the place of Conventional Steel Building (CSB) design concept resulted in many advantages, including economy and easier fabrication. In this study, an industrial structure (Ware House) is analyzed and designed according to the Indian standards, IS 800-1984, IS 800-2007 and also by referring MBMA-96 and AISC-89. In this study, a structure with length 187m,width 40m,with clear height 8m and having R-Slope 1:10,isconsidered to carry out analysis& design for 2D frames (End frame, frame without crane and frame with 3 module cranes). The economy of the structure is discussed in terms of its weight comparison, between Indian codes (IS800-1984, IS800-2007) & American code (MBMA-96), & between Indian codes (IS800-1984, IS800-2007).